Видео

Why not just change the springs in the door?

Great video...I just ordered mine 2 days ago for my 2013 Silverado. I have a plastic bedliner and woke up in a semi-panic this am thinking Im going to have to cut slots for all the brackets but I see you didnt cut anything.

Link is not available :/

Great video! What are you doing next?!

I would've came off the battery and straight into a on & off marine switch next to the plug. That way If ever sell the truck it doesn't become an issue. I would not buy a truck that the electrical was played with. Any thoughts?

Morimoto seem to light up the sides a lot less thank the stock… idk if that’s good upgrade or not

Please give me the information on the sliding screen door!

how many man hours you have in this ?

sorry but can you explain how this will NOT run down the battery if left on?

Did you find out where the leak started from??? Mine started with a leaking in the roof that went into the garage floor then the door soaked it up like a sponge... It's amazing how much they charge for these and the craftsmanship is pure sh**...

The video ended too early

How well does the 12v plug stay in while bouncing down the road?

Just asking how hard is to remove the door and the door hinges has tension. I’m planning to remove my from my stealth toy hauler

Just purchased the same Rapture trailer and I’m already pre planning to do mine. I’m glad to see your video because I had no idea how it’s constructed. Thanks for sharing!

Just booked our trip to Dubrovnik yesterday. Going for 8 nights in October. Can't wait. Great video from you to showcase the place.

What size wire did you run up to the bus bars?

This is super helpful. I have this trailer and this exact problem. How did you get the springs at the bottom of the door back in place? Did you have to hold them down while you put the door in place? Thank you for the video. It really helps!

If you are replacing stock OEM LED headlights on a 2020 Raptor what plug on the LED light harness do you connect to the Fuse Tap Harness?

Looks great

Get video, but your link to the 12v is really for the wire.

Saving for our 29RKP side patio rebuild. Thank you thank you for this great video!

Would you recommend these over the morimoto 4banger lights?

I’ve seen a couple mount a small winch with a release cable to lower/raise the door. Saw one in action that works well. Mounted center top

Incredibly helpful. Just grabbed a 2019 myself.

Hey nicely done. You definitely need an air filter extension kit though. Otherwise it will suck in dust and even water if you go through a river crossing while the air compressor is hot. Will kill the compressor pretty easy. ARB sell the extension kit but it's basically a bit of hose and you can clamp a cheap little fuel tank filter or whatever to the end of it. Zip tie it up somewhere high. Thanks for the video

Just got myself a 2019 raptor, forsure ordering a pair of these, great video

I have the same problem that you had. Mine is a fuzmion. I bought the loctite Max premium but it is too thick to get out with the calking gun. I called the factory and they said it is supposed to be a thick paste. Did you have trouble spreading it?

Only complaints I have with mine is fuse tap. There are times after I get out lock the doors. It takes up to five minutes for the DLR‘s to shut off, needs to be a better circuit that shuts off immediately after you lock your doors.

Just curious what’s the other connection above where you mounted the power? Thanks great video

Are you telling me there was no wood or aluminum tubing in the middle of the door? Only around the outside?

Why didnt you silicone the bolt holes? All the rest looks awesome

Im having an issue with a repair shop right neo thay did this to my ramp, but the work is horrible! There was half inch gap around the entire inside frame i could stick my fingers in. I have pics but cant load to coments.. they filled the gaps with thick globs of silicon.. and they destroyed the ramp floors grip tape, and replaced it with 4 squares of chrome dyno plate.. it is really ugly and wood is exposed..and the WEIGHT ON IT!!!! NO WAY YOU OR I COULD OPEN OR CLOSE IT WITH ONE HAND.. IT IS BEYOND HEAVY,and they added 2 springs to the door... still increadibly heavy

Where did you get the part that goes on the door to hook the winch cable?

Can’t believe these only have a thin sheet of wood and foam inside. Need to redo mine I don’t have the fiberglass outer piece. Just empty frame. Was thinking 2 1/4 thick sheets of plywood and 1 inch of foam to save weight but that don’t seem like it would even be strong enough to walk on. Thought about 2x10s or thicker ply wood but that would end up pretty heavy.

Any ideas on how to remove the from off the door, I see it took you awhile, mines seem to be welded on, I have a 2016 Jayco Octane

What type of weather seal did you end up using

My lumber yard has marine grade ply. Getting ready to do my 2008 raptor. My uncle said to use recycled aluminum bleacher seating... he did that on his open trailer deck. Probably just what the new aluminum trailers use nowadays. Thoughts? Not very insulated if I use aluminum seating. I think they are too think though.

Job well done!! Great documenting it will help. Two questions is did you notice any tongue weight difference towing because of the additional weight on the tail? What's the estimated weight difference between the two doors, if you had to guess? thanks again.

i am blown away by how little there was to the original door

Great job..Just noticed my 2018 wolfpack 24 has some softness on the bottom of the door..I'm gonna try to take off the door and pop off the trim..We shall see..

I’m not sure but I think my 2011 work and play has aluminum framing inside the door.Blows my mind yours only had foam board.And 3k lb rated,wow.Got a 17 Nitro XLR now.Gona check the doors sealant now pronto !Hell of a good job man!

Great job. I have the same problem with the door on the side patio of my trailer. Any suggestion on where I could take mine to have this done? I don't have the space or the tools to complete such a job. I would take it to the dealer but they just want to sell me a new side door. I don't even want to know how much that would cost. My trailer is only 2 years old and the patio door is already rotting out like yours did so why would I want to replace it with the same type of door that's just going to rot out again in a couple years. the only thing I would do that you didn't would be to seal both sides and edges of the plywood with marine epoxy to prevent the wood from rotting. I have tried sealing every seam to prevent water from getting in but it still seems to be getting in somewhere because the floor has gotten progressively worse.

Thanks so much for sharing your solution!Well done!

What did you use to hook the winch to at the door? I cant see it well in the video. Do you hold it closed with the winch? Ours doesn't close tight at top so i mainly want the winch for that.

Nice video, would it be worth drilling a pattern of 2 or 3 inch holes in the plywood before assembly to lighten the door?

Any ideas on where your leak was coming from? My door has just barely started to show signs of water damage on the inside along the bottom inch. Mostly in the center. I'm not sure where that much water could be getting in from?

Thank God I saw your video. It's exactly what I've been wanting to do but wasn't sure if it could work. How has the winch held up? Any problems or issues you could share with me before I attempt to do this? Thank you!!

In the process now, great video. Is it super heavy to lift up ?

Will be using your video as a reference to redo the side patio on my Grand Design 399TH.

great job!