Видео

Seems ypur phone died during the one bit I needed. How tight was the bolt on the static pulley? I'm wondering if left hand thread or something? Mine seems very very tight. Allen key about to bend/break if I pull any harder...

What kind of tape is that??? It sounds like you are saying "battilly tape".

which size butyl tape?

what a useless video

It's the grommet. Not the door that leaks in F10. People thinks it's the door because it gathers around the back.

I need to solve my leak and understand what you are doing but surely any water should drain away first; how come enough water is building up within the door?

How much tape is required per door?

Thx , solve my problem

Old ass motor mounts on the first one

where can i buy this white/ black product too pick it on the door ?

Hey guys, I do have a same issue on backside left on my BMW F11 ,2012. My question is ,will Bmw give any compensation for this issue?

hey! im painting my car with b09 color. how bad do you think the results will be if the primer is grey instead of black?

Thanks

Elles est abandonné depuis combien de temps

I've just done the rear nearside door on my 2014 F10 530d. Your video, and the similar one by David Wade, were invaluable. Thank you! Wouldn't have attempted it otherwise. Couldn't believe how much force was required to get the door card off, especially the first trim clip or two.

I've just done the rear nearside door on my 2014 F10 530d. Your video, and the similar one by David Wade, were invaluable. Thank you! Wouldn't have attempted it otherwise. Couldn't believe how much force was required to get the door card off, especially the first trim clip or two.

Primer is black?

I fixed leak on my 528i. After adding the tape i used hair dryer, which helped. After removing the door panel a metal clip fell off. It's a U shaped thin metal flat retainer. I spent hours thinking where it might go and got no clue. Does anyone know where it should go?

What point does it make to show a video at super speed so that no one can see what you are doing.

Now try it on a 1.9 TDI

Impressive how you can operate such a condition to letting it start. 👌 Great job, congratulations on your skills!

What adesiv you use please? Give me a link to buy

Man... not on the wet and dirty floor! Do a clean job. Appart of that thx for the video

Yea they found the worst BMW to test it with in the first one lol

Hey man , how much paint did you use ? Can’t figure out how much i need for my e34 ..

How to kill mercedes vans

do you remember size of vbelt, see diffirent sizes everywhere

Hey, do you realign the crankshaft marks until you can put a bolt through them?

Where can I order the Tape?

How did you built that wheel holder? Looks cool

my rear door does leak but only to the outside when you open the door, i can see that it leaks from the door card but this is below the lip of the car body so only pours out when you open the door. do you think this is because its only recent and eventually it will get worse and overflow into the car interior, cheers derek

Epic video thanks!

Looks good! How many liters of paint do you needed for the job?

My car has failed to start

Looks great !

Ай нот андерстенд, найс джоб мэн

Hi Arnold, I went across your e34 525i vids and really enjoyed it. What's up with your head crack issue now? I like the color you painted the BMW a lot and would like to see how it's getting rebuild. I would give this head to some engine rebuilder to get it welded.

do the front doors also leak and will you be resealing them also?

great job. what's last polishing wheel name?

WHY did you trust the same sticky tape for the repair? The original failed. wouldnt some good quality adhesive all temperature glue have been better?

I went to resurface my M50B25TU head and a shop told me they saw a crack in cylinder 3 where the valve seats are but it was hidden from all the carbon that was on it. So I’ve been working on a junk head wasting my time and money on it. Still had to pay the guy even though the head was junk at that point. So I had to search for a clean head. And found a nice fully restored one for $880 but I had to drive 2 hours for it. Where I live, finding a 1738400 vanos head is like looking for a pot of gold at the end of a rainbow. A shame how such a tiny hairline crack compromises the whole head itself. Head gaskets are a expensive job and having a cracked head just doubles the cost. But having a cracked iron block? Man, I’d just throw the car in the garbage bin at that point. Even though it’s easier to get the lower block where I live, just the whole process of dealing with replacing the iron block is a nightmare itself.

Where is the compressor relay on this model 525i. The AC buttons do not light up and so no cold air. Have tried everything else. Thanks for your help. Puzzled me in BC.

That sucks! did the engine overheat?

Pist įlipo per vieną pusę per kitą pusę atėjo 😅😂😂👌

great job, i love when someone is trying and learning, keep it up!

надо её воостановить

Engine M50B20.

How do you dry or drain the water under the carpet? Is there a plug can be used to drain or drill a hole?

Haha really big service timing belt in the service changeable item