Видео

Your video is very clear and Thank you for showing us how to replace the fog light bulbs.

Thanks a lot. May God bless you and your family

"Could you please tell me the size and name of the screwdriver required to remove the four screws? Thank you very much."

Great video, straight to the point and thorough. Thanks

Thanks for this vid

So i dont need a resistor then?

What if when replaced it still doesnt not work

Thank you sir. Very clear. I also need to replace the fog light housing as it is cracked. Can this be done from the backside as you've shown when just replacing the bulb?

Thank you

How about the turn signal bulb? Tough to get to

Thanks

You can pull the bumper and grill off in like 10 min then you have full access to the lights. I’ve done it a few times and it’s a lot easier

precise, succinct, and easy to follow...no crappy effects, blaring music - this guy is peak efficiency. Thank you!

I got a pair of cheap fog like housing on amazon and replaced the original because of that damn shield. Now my fog lights are super bright without that light shield inside. Just make sure to point the LED bulbs down so you dont bling people👍🏼

Thanks. This was a big help.

Thank you for the video. It was spot on how to change the bulbs. Even the tools was helpful.

GOOD

Sensor part number for 2016 Tahoe 5.3 engine TX89 at O'Rielley's about 15.00. That's what I paid. May fit a year range of 2014 to 2017 at least and may be compatible for those year models of GM Yukon's, Sierras, and Silverado with same engines. Check and verify to be sure though.

My follow up to sensor replacement. Author of the video is correct in tools needed, Just completed my sensor replacement 6 Apr 24. Be sure to d/c the battery as it clears the computer memory from kicking the fans on to full blast. My part for 2016 Tahoe LTZ 4x4 was 15.00 bucks at O'Rielleys. A screw driver and needle nose pliers work best 4 my unlocking sensor clip. Finger on sensor hole is a must. System is under pressure. Be sure engine is COLD!! and place wrag around sensor base. I used index finger tip pressure to finalize seating the new sensor. Make sure lock tabs face front of engine before connecting the wiring connection. Secure all components and engine area is clear of tools and battery negative cable is tight before starting engine. Start engine and check for leaks and monitor temp Gauge. You might notice a slight change in where it was sitting before sensor replacement. That's an indication that it received the electrical current to operate. Good Luck.... this Video was a great help to myself and should be to you also. Good Luck.

Really not a complicated repair for DIY and the money saved is probably HUGE.

Thank you for the information. A bit confused. My temperature gauge is showing a minimum reading and runs a bit rough. The fan is also on a full speed. Are you saying it is certainly the sensor?

This video was perfect, thank you 🙏🏽

thank you

Thank you for taking the time to do step by step video, very helpful amd appreciated.

The most complete step by step video instructions ever in the world, this is best reference of how to change heaflight bulbs. Thank You so much from a Tahoe owner.

Was looking for the torque screwdriver size

Excellent Video…comments below..You’re right 👍🏽

What do I do if my 2019 Suburban driver side high beam dust cover doesn’t budge?

So what happens if you dont do that 🤔

Thank you for such a straightforward and detailed video. Made it easy for me to do it myself!

I so impressed with explanation, wonderful video congratulations guys thank you so much

What are the repercussions if I broke the tab when pulling wire connector off. It won’t click back into place anymore

very helpful

This video was perfect and the best explanation I found online for performing this simple change. Thank you!

Thank you for this video! I changed my headlights by myself.... following your video it was a breeze!

Love it, explain it like no others .,.! Thank you a bunch amigo 🫶

Great step by step ty

Very informative. Did you remove the air valance from the front? Any notice in gas mileage?

This video helped tremendously. Still took me about 1 1/2 hours, but I am very far removed from a professional. Thank you again for posting!

This was excellent! Instructions were clear and easy to follow. I really appreciate it!!

Thank you for sharing this!

Thank you for posting this! My check engine light just came on. My gauge shows the minimum of 160 degrees and the fan continues to run. I had a feeling it was the sensor.

Thank you! I am not handy at all and I was able to follow along with success!

Very helpful, thank you!!

Great video! I do have a question I did install LED lights but now the remote start is not working, would this be because to the lights?

A huge help!! Thank you😊

Thank you sir.

Thank you for getting right to the points and not over explaining things like so many do. Your voice is like the Mr Rogers of auto tutorials good job sir

This by far is the best video.

This is not an LED bulb. That's a standard halogen bulb. Title is misleading.