Видео

Thanks for explaining while the manual is very vague.

Sir, please tell me why my left drive handle lags ~4 inches behind the right handle while trying to mow straight. There are no loose linkages, bolts, nuts and ball joints. Very much appreciated...

I have a new DK 4720 with 70 hours, yet to have 1st service, my region came on and startled me, internet stated "red" shut off immediately. What is reagen? btw, all ive done is mow the pasture, no ruff stuff. Thoughts?

Thanks!!! Any videos on how to align the handles. Tightening or loosening the spring bolt does nothing. One handle is on forward of the other by 1.5 inches. ( Using adjustable knob handles) Thank you!!!

This fixed my zt avenger, required two turns per side

On avenger i have no creeping but resistance on control arms are really stiff, hard to know exactly where neutral position is while mowing also. Couple hours on the machine. Can this be adjusted also? Or does it need to be greased or shit gas struts causing this? Ill bring back to dealer if needed but it's a all day event which i prefer to avoid...

If you use 20w-50 try to use a brand with high zinc content !! Kawasaki 20w-50 , Castrol GTX Classic etc. Anything with high-zinc will make them operate smoother & just about double their life !!

Would this 10 -12 psi apply to the Bad Boy AOSD 7200 with 10 ply skid steer tires in the rear?

10-12 for any and all tires? My 60 inch ztr has a max pressure of 22lbs. So half that?

THANK YOU!

The diagram for the hydro pump belt for my 48” 2019 revolt is incorrect. Put a new belt on and ran the belt the way it should be. 59” belt. Can you tell me what the belt length should be?

Great advice, thanks! More informative than the BB Channel.

If it comes with 20 W 50 way not put 20 W 50 back in it?

I have been searching for almost 2 hours of how to adjust the push rods to straighten out the tracking on my bad boy. You are the first one to actually show how to do it. Thank you so very much. I will continue to follow your videos from now on.

What about atf if it’s the best you got

Bad Boy does not manufacture oil, they just put their name on it and charge you more money for less quality.

If you expect Scag or Exmark cut quality then buy one of those mowers. Bad Boy is made simple and cheap with a big open deck to cut grass and get it out the discharge as quick as possible. Scag decks are made to "groom" the grass with the design of the baffles but it also costs more. Cheap and dull blades are the main reason the cut sucks. Use Oregon high lift or Gator blades and keep them sharp, you won't have a problem. If you still do and the deck is noisy, the cheap ass sealed spindle bearings are the problem. A Bad Boy is the Chevy of mowers, not the Cadillac.

Bad boy has a quality cut problem if they didn't they wouldn't be making this video to cover their butts.

The pictures in the manual are so close I cant tell where theyre talking about.

I have a kioti this does not work.

como se regenera en un kioti rx 8030 ya que no tiene boton de regenaracion

getting ready to put a new trans axle in the right side on my maverick. are the brackets that the tranny slides int and sits in supposed to be a little loose or should they be tightend up?

Very not helpful!

USLESS VIDEO!!!

You try to give the video more brightness it will be great if you do

Not helpful at all

Très beau tracteur Doit être très agréable à conduire. En êtes vous satisfait ? Combien avez vous d'heures de travail avec ?

That was helpful . NOT ! !

could you make the deck belt pulley grease fitting easier to get? you have to raise the mower high as heck to get to the fitting. especially if the fitting won't take grease. my mower is brand new not easy for an old guy like me. the dealer greased the two drive arm fittings but not the pump belt and drive arm. i want to do that before using it.

Not very helpful but still better than nothing :) Catch an upvote!

How you get off the tractor without it turning off?

NO ONe shows how to grease the pump belt tensioner fitting! The Manual shows where it is. Other than that, it is useless. I have never found a video covering it either.

The one for the hydro gear drive belt on my 2011 ZT 60 has that same decal and it doesn't match the reality of what is under the mower. for that belt And there's almost no info online on the procedure for changing the belt. Mine was missing half of the inner portion of the belt. I ordered a new belt and now I'm having all the "fun" of trying put the new one on figuring it out one step at a time. It's been one heck of a mower for me, but at times when I'm having to work on it, I'm about half a mind to just drive it off into the pond.

The diagram for the hydro gear drive belt is incorrect . Need to send out a bulletin.

Seriously? This video has been up since 2017 and nobody (esp.@corporate) thought to put the URL in the description? (Oh yes, it's at the bottom of the screen, but most people look for links below the author's name. I heard that ball drop all the way up here in Maine. If I had a company and anyone dropped the ball that badly, I'd be looking for a Maine person to pick it up and run with it. Good luck Badboys! (I just bought my first Badboy and hope it won't be the last, but also hope I won't need to upgrade for some time!

Got it.

Thanks for nothing.

I have owned this tractor for a year now. Almost 100 hours on it. So far it has been great. Very capable for its size.

Bad boy movers are horribal

This video was not informational at all

Great mowers... the best I’ve owned

Welp, that's 69 seconds of my life I won't get back...

*_This is a real robot,>>>_**_t.co/308znbEVKp_**_ Once you lay down the wire, After a couple days you'll notice that the lawn is fine_*

great mower well worth the money

Hi Jordan I was reading on your channel that you are kioti dealer I seen your video of the fork lift on your kioti and I need one for my 2011 kioti DS3510 plz comment back I'll appreciate it or call me at 2096880514 my name's mele I'm using my wife RUclips account thanks for your time

Can somebody please do a video on backhoe attachment removal for the TYM 394