Yanes’ Garage
Yanes’ Garage
  • Видео 17
  • Просмотров 38 688
Mercedes problema en suspension de aire
Este mercedes Benz tiene un problema en la suspension de aire , causado por falla en módulos o computadoras, el problema se genero a causa de filtración de agua dentro del vehículo causando un corta y corrosión en el cableado y módulos del vehículo, si el video te sirvió y gusto, suscríbete a mi canal pronto estaremos compartiendo mas problemas eléctricos y diagnósticos
Просмотров: 14 144

Видео

Nissan versa spark plugs replacement
Просмотров 45Год назад
Spark plugs replacement on a nissan versa 2013, any questions leave a comment , I’ll be posting more vides, like and subscribe for more content!!
Bmw x1 problema electrico
Просмотров 1 тыс.Год назад
Estaremos diagnosticando una falla electrica en este bmw , problemas con la ventiladora y el main fuse .
Electric hydraulic hole puncher
Просмотров 350Год назад
Using this electric hydraulic hole puncher on a beam for a building structure , this way is more faster and accurate, around 80 holes were punched in less then 15 minutes.
Jeep wrangler hub bearing
Просмотров 58Год назад
Jeep wrangle jk 2007-2017 front wheel hub assembly replacement procedure.
Dodge charger power steering leak- fixed
Просмотров 3,6 тыс.Год назад
2014 dodge charger- electric power steering was leaking at the reservoir O’ring, this is a common leak, make sure before you replace it that this is your problem, if you gonna replace the second O’ring at the base of the power steering pump, remove it from the car that gonna save you a lot of time and it’s easier to put it back together, make sure you use the right power steering fluid for this...
Land rover LR3 thermostat housing replacement .
Просмотров 4,7 тыс.Год назад
2007 land rover LR3 4.4 thermostat housing replacement. same process for 2005-2009 ranger rover sport.
Algo esta cayendo aqui- piano tutorial(intro)
Просмотров 37Год назад
Algo esta cayendo aqui- piano tutorial(intro)
Intro tutorial "y vino tu presencia Eben Ezer"
Просмотров 10 тыс.8 лет назад
Intro tutorial "y vino tu presencia Eben Ezer"

Комментарии

  • @HectorMartinez-m2d
    @HectorMartinez-m2d 12 дней назад

    Cómo arreglaste o cambiaste la placa

  • @CarswithNash
    @CarswithNash 3 месяца назад

    There's no need to take the intake manifold off, just pull the throttle body off the front of it. I hate to think how many people have removed all that just because of this video...

    • @computerwiz4
      @computerwiz4 3 месяца назад

      I can see why they went the intake manifold removal route though. I did the throttle body removal, but it requires a lot of patience, small fingers, and a bendy socket because of the very tight access to two bolts on the right of the throttle body.

    • @computerwiz4
      @computerwiz4 3 месяца назад

      A tip for anyone else tackling this job without removing the intake manifold: some used chewing gum also helps to hold the bolt in the 8mm socket when trying to guide the bottom right bolt back into place with the bendy socket.

    • @CarswithNash
      @CarswithNash 3 месяца назад

      @computerwiz4 It's not hard at all! My 15 yr old son with limited mechanical experience, did it on mine, he had no issues. In fact, we have been doing a bunch of work to this vehicle and have both been remarking on how easy it is to work on.

  • @adrianolivaresl.929
    @adrianolivaresl.929 3 месяца назад

    Cuento con una mercedes benz gl 500 2009, Después de las lluvias , Al día siguiente la maneje y la suspensión trasera estaba en altura normal, y la delantera en lo mas alto , Como si fuera a despegar como (avion), Al siguiente dia estaba completamente sin aire , y sin corriente en los botones, completamente apagados, Le conectaron scanner , Y la información es que no existe comunicación entre los elementos, Se checaron los fusibles y no tienen corriente en ambas partes

  • @adrianolivaresl.929
    @adrianolivaresl.929 3 месяца назад

    Buen dia , excelente trabajo

  • @angelesparza904
    @angelesparza904 3 месяца назад

    Excelente trabajo lastima que no se pudo terminar el trabajo gracias por tu porma de buscar la falla

  • @josejavieralbentosaconejer8915
    @josejavieralbentosaconejer8915 4 месяца назад

    Primer video que veo pero no lo he podido terminar de ver, la música es insoportable. Saludos.

  • @boxingclubterrassa
    @boxingclubterrassa 5 месяцев назад

    Impresionante el trabajo Enhorabuena

  • @edwinbecerra6982
    @edwinbecerra6982 9 месяцев назад

    Excelente trabajo. Felicidades y éxitos en sus funciones. Saludos desde República de Panamá 🇵🇦👍💯👏

  • @999kaheem
    @999kaheem 9 месяцев назад

    what is the cover called for power steering pump and fluid did you use

  • @eg4941
    @eg4941 9 месяцев назад

    Gracias por el video

  • @livestreamspinningchile6683
    @livestreamspinningchile6683 11 месяцев назад

    Hola estimado, tengo un Gls 350 y estyá indicando (avería) el scanner arrojó fuga del sistema de aire comprimido

  • @alfonsotorreshuizar5199
    @alfonsotorreshuizar5199 11 месяцев назад

    Es un problema tener una Land Rover creo que mejor la aviento al kilo dé metal cuanto trabajo para arreglar éso

  • @leroyking3058
    @leroyking3058 Год назад

    How did those gaskets work out for you. I got the same ones from ebay they are the same size ..I was told one gaskets is a little bit bigger...not sure should I use the ones I got...and you don't have to remove the bracket?

  • @mvivanc
    @mvivanc Год назад

    Me pasó una vez igual con mi x1 nunca me había sucedido. No se si tenía que ver que ese día pasé por un charco muy grande. De pronto vi el mensaje de temperatura de motor elevada. Me orille me estacione y vi que no prendía el ventilador. Solo apague el coche, lo volví a encender y ya funcionó. Pero me quedé preocupado 😢

  • @metromotel
    @metromotel Год назад

    I just had my replaced due to very small leak from the housing. Was thinking to try stop leak liquid but after thinking twice i took it to mechanic. They charged me for 3.1 hours. I asked for the old part, took it home and opened to see out of curiosity. The rubber seal has already kind of melted (main reason for the leak). A plastic round plastic part inside the housing which is touching the spring was also broken.

  • @joseortiz-mq6ku
    @joseortiz-mq6ku Год назад

    Buenas tardes porque mi Mercedes-Benz gl450 no esta cargando la suscripción de aire y me aparece malfunction

  • @mateo006
    @mateo006 Год назад

    ¿De dónde sacaste las fotos del desmontaje del coche? había dos fotos

  • @joseignacioortizcervantes5537

    Hola, me paso lo mismo con mi camioneta, se le cambio gateway modulo central y el amplificador no lo pude cambiar por que no lo encuentro. Pero ahora dice en el tablero averia en suspensión y me dice el mecánico que es la bolsa de suspension delantera derecha, pero viendo tu video ya tengo mis dudas que el modula haya sido del mismo. Te encuentras en México?

    • @Yanesgarage
      @Yanesgarage Год назад

      Tendria que revisar por que el mensaje de suspensión, puede ser muchas cosas todo depende del problema, todas las bolsas de la suspensión estan sin aire?

  • @pudrete1470
    @pudrete1470 Год назад

    Tengo la misma falla, mismo motor misma x1 , pero el arnés es diferente

  • @alealfa496
    @alealfa496 Год назад

    Excelente video

  • @bunniie5754
    @bunniie5754 Год назад

    How would I know if I need to change the whole electric pump ?

    • @Yanesgarage
      @Yanesgarage Год назад

      What is your problem? No power steering at all?

    • @bunniie5754
      @bunniie5754 Год назад

      I bought the res and orings and replaced it and it’s still leaking from under the res And says service still it is has power steering but was low when I started it all due to it leaking from the res part

    • @bunniie5754
      @bunniie5754 Год назад

      Im not sure at what point I’d know when it might just need the electric pump it’s not leaking from the back part of the electric pump just the reservoir

  • @srad2999
    @srad2999 Год назад

    I don’t need to take off the injectors line right?

    • @Yanesgarage
      @Yanesgarage Год назад

      U don’t have too, U can just remove the bolts by using a swivel, but I just rather take it off to make it more easier and clean

  • @srad2999
    @srad2999 Год назад

    Perfect you video thanks so much ill make this job tomorrow on my disco3 4.4

  • @tyurzak
    @tyurzak Год назад

    Loving the camera placement on some of these shots. Super helpful stuff man. Thank you.

  • @Connoisseur617
    @Connoisseur617 Год назад

    You could of just took the front part off of the intake instead of doing all of that I’m confused

    • @Yanesgarage
      @Yanesgarage Год назад

      I replaced some injector too, and while I was there I took the whole intake to clean it too and engine bay as well, make it more it easier and do some inspections around👌🏻

  • @3amoorzi
    @3amoorzi Год назад

    Do you turn the wheel left and right 10 times with cap off or on?

  • @pepev606
    @pepev606 Год назад

    Amigo buen día saludándote de Monterrey NL México. Pregunta se me reventó una bolsa suspensión trasera se puede rodar así para llegar a un taller?

  • @fabianvargas-mc1zx
    @fabianvargas-mc1zx Год назад

    hola... muy bueno el video.... mira, a mi me ocurre lo mismo con una GL 350 diesel, año 2011..... la tuve guardada un año y medio, al encenderla la suspension no funciona. aca en donde yo vivo ningun mecanico quiere revisarla... esa es mi falla...ojala me puedas ayudar...gracias...saludos de arica-Chile...

    • @Yanesgarage
      @Yanesgarage Год назад

      Saludos, que tal ? De casualidad tienes otro problema que notes ademas de la suspensión?

  • @kennyacosta6477
    @kennyacosta6477 Год назад

    Cómo anda pri con todos los poderes

  • @carolinaramoscardona8259
    @carolinaramoscardona8259 Год назад

    Guau!!! Que pasada!! Gracias por estos vídeos.

  • @MelvinRodriguezxTNGx
    @MelvinRodriguezxTNGx Год назад

    🔥🔥🔥🔥🔥

  • @Yanesgarage
    @Yanesgarage Год назад

    ruclips.net/video/68vlhCu_t7E/видео.html

  • @Yanesgarage
    @Yanesgarage Год назад

    ruclips.net/video/68vlhCu_t7E/видео.html

  • @northtexasbullysquad6986
    @northtexasbullysquad6986 Год назад

    That's when you look for one thats close enough 😂

  • @kelseyilarraza2718
    @kelseyilarraza2718 Год назад

    👏👏👏

  • @brithanydupring4168
    @brithanydupring4168 8 лет назад

    Kevin porfa..me falta la partr que dice hoy tu espiritu es todo en todo xq tu toque cambio todo en todos

  • @brithanydupring4168
    @brithanydupring4168 8 лет назад

    Y que paso con el resto de la cancion ya todos nos ssbemos la intro el resto xfavor..sino es mucho pedir

    • @Yanesgarage
      @Yanesgarage 8 лет назад

      ehh ok, dentro de pronto lo subire vale.

  • @willycortes7884
    @willycortes7884 8 лет назад

    alguien puede darme las notas de este canto,por favor...gracias Dios le bendiga..

  • @ivanenriquelopez1491
    @ivanenriquelopez1491 8 лет назад

    Muchas gracias hermano me has sido de mucho ayuda bendiciones

    • @Yanesgarage
      @Yanesgarage 8 лет назад

      no hay de que😊 bendiciones!

  • @ivanenriquelopez1491
    @ivanenriquelopez1491 8 лет назад

    Tu video es muy bueno y ya pude sacar este canto solo me falta el intro estoy confundido bendiciones y que mi padre te siga utilizando

  • @ivanenriquelopez1491
    @ivanenriquelopez1491 8 лет назад

    Disculpa hermano otra vez yo lo que pasa es que estoy con fundido en el acompañamiento del intro uso LaM, F#m, ReM y MiM no pero no estoy seguro que acompañamiento usas tu?

    • @Yanesgarage
      @Yanesgarage 8 лет назад

      oh mira en la intro yo hago los acordes Fa#m-Re-la-Mi

  • @ivanenriquelopez1491
    @ivanenriquelopez1491 8 лет назад

    Disculpa me podrás decir que tono es el canto?bendiciones!!!

    • @Yanesgarage
      @Yanesgarage 8 лет назад

      hola, bendiciones yo lo saco por F#m

  • @johaanandujar9588
    @johaanandujar9588 8 лет назад

    muy bueno