- Видео 31
- Просмотров 362 097
MileMarker116
Добавлен 3 фев 2012
This is an official channel for CornfieldCraziness.
Видео
Cruising Through Amish Country In The Dodge Ram
Просмотров 48012 лет назад
Started out as a test drive but ended up being a tour through amish country in the Dodge Ram 1500.
Replacing the rearview mirror in the Dodge Ram
Просмотров 22 тыс.12 лет назад
This is how I replace a rearview mirror after the hot sun causes it to fall off.
Putting the bed back on the Dodge Ram
Просмотров 57 тыс.12 лет назад
Putting the bed back on the Dodge Ram after replacing the fuel pump module.
Replacing the Fuel Pump Module on the Dodge Ram
Просмотров 55 тыс.12 лет назад
Replacing the fuel pump module on the Dodge Ram.
Transfer Case Maintenance on the Dodge Ram
Просмотров 1,5 тыс.12 лет назад
Doing some routing maintenance and not so routine maintenance on the transfer case of the Dodge truck.
Dodge Ram Drive Test - Fuel Pump and Brakes
Просмотров 22112 лет назад
This video unfortunately got out of order but should have been after the videos of the fuel pump module r&r. After replacing the fuel pump module this was the test drive and wrap up video.
Doing an Electric System Test on Dodge Ram
Просмотров 21412 лет назад
Checking out the electrical system on the Dodge truck. Everything seems to be fine now.
Truck Restoration - Interior
Просмотров 2,2 тыс.12 лет назад
Doing some project work on the 1948 Ford F-5 Truck.
Truck Restoration - Fiberglass Floor Patch
Просмотров 15 тыс.12 лет назад
Doing some project work on the 1948 Ford F-5 Truck.
Truck Restoration - Doing the Shuffle
Просмотров 7812 лет назад
Doing some project work on the 1948 Ford F-5 Truck.
Truck Restoration - Instrument Panel and Floor Sections
Просмотров 38712 лет назад
Doing some project work on the 1948 Ford F-5 Truck.
Truck Restoration - Wiper Motor Pt. 2
Просмотров 2,4 тыс.12 лет назад
Doing some project work on the 1948 Ford F-5 Truck.
Truck Restoration - Wiper Motor Pt. 1
Просмотров 9 тыс.12 лет назад
Doing some project work on the 1948 Ford F-5 Truck.
Truck Restoration - Seat
Просмотров 19312 лет назад
Doing some project work on the 1948 Ford F-5 Truck.
Plowing snow with the garden tractor
Просмотров 3,3 тыс.12 лет назад
Plowing snow with the garden tractor
Mounting a Western Uni Mount Snowplow
Просмотров 102 тыс.12 лет назад
Mounting a Western Uni Mount Snowplow
Getting ready to assemble the swing bike
Просмотров 3312 лет назад
Getting ready to assemble the swing bike
You should put your camera where you are not blocking what you are doing
Was this a half Ton or 3/4
When you raise what up and down?
Thank you very helpful
Thanks a lot. My dad Left me his 97 s10 pickup truck up with a uni mount western snow plow. He never let me operated his snow plow all those years. I didn’t know How to hookup his plow until this video.
They forgot to but something to stop rust first
Where does the vacuum hose attach on the engine?
Interesting video...............................looking at the back of his coat.
Well Done
i like these better than the flimsy new mounts they bend way to easy when you hit debris plowing in country reminds me of the old northman plows
11 years later, is that saw stihl working?
P I.p.o popluup008p)l))))))))))))))))))))))))))0
You people that make vedios holding your camera shouldn't,,,only idiots keep watching
what did you hook the straps to, to lift it? the loops bolted to the corners? I'm going to have to pull my bed to change the fuel pump, and I want to use something like your block, and my tractor FEL to take if off and put back on
Uni mount is trash compared to ultra mount.
THANK YOU...A BIG HELP...AS I WANNA SWAP OUT MY PINS FOR MORE USER FRIENDLY ONES....
Where can I get this swing bike from
When I was serving my time I was taught to cut out sections and punch holes before cutting the perimeter
Crap job you did no good it all
Wat was the problem that you had too change it??? And do u have to remove the number?? Just wondering
I just bought this setup mounted on a used truck. I have read many complaints on what a pain these r to hook up and unhook. Its not, as your video shows. Mine came with the chain to tight which left no adjustment for up and down, and the top pin missing for the foot
Please use better lighting. Thanks
I guess his dad was a glass maker
Very nice
Chain brake position?
Thanks for the video. I can't believe you didn't sand blast and paint the frame before reinstalling the bed. That's one of the main reasons I want to remove mine. That and to remove the spring shackles and install a flip kit. and possibly a dump kit. We definitely need some good rust protection for PA winters.
So many things wrong with this video. I presume you didn't post what really occurred over the next few days? You have a primary head gasket below the valve plate that you didn't even check, much less remove and replace - that's the one that was blown. You needn't drain the system to do this unless your check valve is shot/leaking, or you do a ring/piston job on it, hence, leaving the loud draining air throughout the video was unnecessarily annoying. Odds are high, the cylinder surface or head or both, are warped. Very common on these models and painfully expensive to repair vs a new pump.
No idea what your torque might be?
Did u ever find out?
Thanks for the tips. We are about to remove a bed and install a Flat bed.
I really enjoyed Roy's videos. Thanks for letting us know. I loved his video on ground cherries.
5:00 You want anti-seize on those bed bolts, not thread locker, and use new ones, if possible. Sounds like someone may have told you to do that, and you questioned your memory. They're like exhaust bolts, they'll rust and be a bitch to get apart next time. Thread locker is completely unnecessary, but at least it's not going to make things worse than if you hadn't used it at all.
Amigo buen video pero quería saber qué número de parte es la bomba esa
keep the fucking camera still
hi
What is the part number to that controller
Hate the unimount plows. Thank god western came out with the ultramount. Unimount is a pain and takes forever! Worst plow hookups I have ever seen. its a disaster
Go look at a snowdogg lol
Waaaah
Sorry Dude, but you flat out suck. No way around it. You're slow and inefficient.
thanks, saved some headache!!!
I wonder why every body shop is telling me that this will not work. I told him I saw it on RUclips and they said that's why it won't hold up.
They tell you it won't work because you can do this yourself (as long as you remove all the rust and clean with a degreaser first). Most people can't form and weld new floor pans from metal. They are just trying to preserve their paychecks. I have seen this done to vehicles in the 1980's and the jobs hold up to this day.
Where did you get that fuel tank? It looks brand new!
Alex Klejka eBay
The store lol
great
get out of the fucking way dip shit
Thumbs down for not getting close shots of the work.
Super helpful. Thanks!
this was very helpful...thank you!
Just the video I was looking for. Thanks :)
Thanks for the help... my plow came with my truck and didnt have the jack stand. Makes things a lot more difficult
You make it look easy. Takes me about 1 hour to mount my snow plow.
I appreciate the video! I always forget how to start, and the video helps!
All I see is your leg and and back..horrible filming