Видео

@hoosierbuddyadventures thank you for watching. Scale accessories, there are a few websites I go to to look at, amain and rc4wd are 2. From there, I'll go to our local hobbyshop and see if they have what I am looking for or if they can order it for me. For mounting them, some will come with screws and if not, I'll ziptie them or hot glue. The driver figure, I just found a 7 inch one on Amazon. These could be at Walmart or Target, not sure of that. I think a figure from 7 to 8 inch would fit petty well. For the one I have, I just put velcro on his bottom, and it worked pretty well.

Thank you for watching. The LED flasher is the Utility flasher from MyTrickRC. You can go to their website mytrickrc.com.

@MaxxPainII Thank You for Watching. I didn't change anything but I might have stiffened the springs a little. The shocks did leak a little but once cleaned I rebuilt them and used 50wt shock oil. It may sit a little higher but the links front and back are just about parallel with the ground. I liked the shocks alot and once rebuilt there're still smooth 😀

Thank You for Watching. I am hoping we get snow this year so I can get this Plow Truck out to do some work. Last year we pretty much got wet snow and could not do anything worth videoing.

@@henrysrcgarage5210 crazy how the weather has changed over the years. When I was a kid it would snow for weeks. Hope to see some more good videos. Maybe you can make a lawnmower?🤔🤔

@AADABOSS42 I've thought about a lawn mower and even a street sweeper 😆. Yeah with you on when I was a kit we had snow typically end of October till April. We got feet upon feet of snow. Not so anymore...

@travelinwithTODD thank you for watching. The LED light bar is from Vanquish Products. It is 6" and part # is VPS06751. These have been out of stock on their website for a while, and I'm not sure when they will be back. That does not mean there isn't one available at a local hobbyshop.

@@henrysrcgarage5210 thank you for the info. i am trying tp upgrade my CJ7.

​@henrysrcgarage5210 do you happen to have a normal speed video of taking off the front part to drill the holes. I must be dumb. I can't seem to get that part off

@@travelinwithTODD I looked at the video and I did it via time lapse. Sometimes I do not do that but I guess I did with this one. There are 2 screws holding the bumper in the chassis rail. One screw is part of the Panhard mount with a flathead. The other one is a button head. On the backside of the bumper there are 2 buttonhead screws as well. sorry I do not have a normal speed video but hoping what I said above helps.

@@travelinwithTODD here is the link to the CJ7 Manual. There are exploded views and on page 53 should help you a little. www.axialadventure.com/on/demandware.static/-/Sites-horizon-master/default/dw2ea94ae3/Manuals/AXI03008_Manual_EN.pdf

Thank you for watching. Yeah right there with you. Someone mentioned tome recently that I should make it into a street sweeper. 😀

Thank You for Watching. The Garage can be purchased from rcgarages.com/. If I recall I bought the 60"x30" Warehouse 1/10th scale. I really love my Jeep CJ7. I recently took it to Axialfest Badlands 2024 and it performed really well with all the upgrades I did to it. You won't be disappointed with your pick and happy tiny trucking..

@@henrysrcgarage5210 Thank you!

@Fullthorttleexcavation the plow made by Rick Perry. You should be able to look him up in the CEN Racing Facebook pages. He has posted alot on the plows in the past.

@@henrysrcgarage5210 ok thanks

@@Fullthorttleexcavation the utility flasher is from MyTrickRC.

@SCRedneckRC_2024 Thank You for Watching. Yeah it was the 1st part we went too once we got dropped off. It was a cool to do.

That looked fun , some great trail set ups

@ironmover5800 thank You for Watching! Yea there was awesome trails again this year. Even though it was in the 90s, it was still lots of fun.

@philadelphiacollins2460 Thank You for Watching. The foam is Proline's 2 stage foams, part number PRO617400.

Thank you for Watching..

Thank You for Watching. No that I am aware. I do know he is in the CEN Racing Facebook groups. You should be able to find a post for him on these plows.

Thank You for Watching.

Thank You for Watching. I will typically set my end points to zero and work from there till I get the engagement needed. Then I'll leave it in one position and monitor if the servo starts to heat up. Then flip to the opposite and monitor for heat. This is pretty much my process.

Can you do a video showing how to set the end points on the Mt12.

Thank you for watching. I an happy this video helped.

Thank You for Watching. I was at the hobbyshop near me on Friday and they sold the last few they had I believe. It's a popular RTR for sure. The body I think is what we all are really wanting, 😁

Thank You for Watching. Yeah I agree. It is fun...

Thank You for Watching. Yeah, I hear you. It's seems like sometimes these tiny trucks feel like a 1:1 price tag when you start to add things up, LOL.

Thank You for Watching and Subscribing. You are welcome for the info and hoping it helps you in your build.

Thank You for Watching. Not sure what the issue could be if you have the 4 in 1 version. I have heard/read a while back in the FB pages where if you have the ELRS version you need to do something in the radio to get other channels to work.

Same I have the 4in1 just like his and have exact setting but on channel 3 and it won’t work

@Paintscustomcrawlers thank you for watching. Are you using a winch with an built in controller like the Reefs Rc 422hd winch for example? Make sure the rx connector for it is installed correctly, ground to ground, power to power and signal to signal in the rx ch port. If you are using a rc4wd warn winch, you need the controller to work the winch. Did you happen to setup the winch exactly like I have it except for ch 3? Did you also happen to have the 2 switches installed on the base of the TX? This is how I'm activating and deactivating it. If so, in the special functions, try unchecking the check box and click return. The winch should work without a switch to activate it.

@@henrysrcgarage5210 I’m using it on a reefs 99 micro winch I had it set up without the switch’s at first and just had it set to t3 but wouldn’t work so I changed to the f2 switch and still nothing. But my controller also won’t let me switch the trim switch’s to 3position switch’s

@Paintscustomcrawlers odd you cannot get T3 to work. As far as I know and experienced on mine is any of my T switches once I changed them in drive mode zero from colon zero to dash dash it deactivated them from working as trims. Once I programed mixes on channel 5 to T1+ to positive 100 and T1- to negative 100 it worked as a momentary 3 position switch. I know on the Reefs servos you need to ensure the gray wire on the servo plug goes to the signal side of the rx. I have flipped it a time or two without realizing and wondered why it was not working. I am also wondering is if I'm on a newer version of the firmware right out of the box. I have heard some of the earlier ones were on an older version then what I have. I'm on firmware version 2.10 if I recall.

Thank You for Watching. I got the plow from a Rick Perry in the CEN Racing Facebook Page.

@@henrysrcgarage5210 alright thanks!! I loved the video btw

Thank You for Watching. In this truck along with my 6x6 snowblower, I put in some lead weights I had spare from my rc pulling trucks. The weights seem to help give me some weight to get grip.

@@henrysrcgarage5210 awesome looks great

Thank You for Watching and thank you.

Thank You for Watching. Sometimes I do surprise myself in what I'll know in a short time. Hopefully this has help you out.

If you are referring to the Fine Lazer Designs clipless body mount. Yes they do, link below. I have other mounts and they all work great. www.etsy.com/listing/1367578627/axial-scx103-early-bronco-clipless-body?click_key=95bd0c26b20a558beb11b4928459b29379bd60db%3A1367578627&click_sum=76772d0c&ref=shop_home_active_6&crt=1&sts=1

Thank You for watching. With the weather getting better and the ground drying up, I'm hoping to get the CJ7 out for a run. I know it will perform better since lowering it a bit with the 90 mil shocks.

I like the VS4-10 Pro. It performed great in the stock form and at the moment not seeing where I need to improve it any but time will tell if I need too.

Thank You for Watching. You are welcome and can agree with you on reading through post after post to get a feel of what you are looking. Sometimes it could be hours before you know it.

Thank You for Watching and the support the M12 content.

Thank you for watching. The utility led bar and plow leds are from MyTrickRC at mytrickrc.com. The other leds are from 110rodshop.com.

Thank you for watching. Yeah this is fun in the snow. 2023/2024 was limited on snow for us this year so everything sat idol but hoping we get some next season.

Thank you for watching. This plow is setup on my Spektrum DX6R radio.

@henrysrcgarage5210 thank you that is such a cool rig love the vids

Thank you for watching. Yes you can get one from RC Garages at rcgarages.com/. There are several configurations to pick from.

Thank you for watching. I've had these for a while now. I got them from AMain. SSD RC Locking Hub Installation Tool Part#: SSD00008 www.amainhobbies.com/ssd-rc-locking-hub-installation-tool-ssd00008/p498695 SSD RC Scale Locking Hubs (Red) Part#: SSD00011 www.amainhobbies.com/ssd-rc-scale-locking-hubs-red-2-ssd00011/p498698 SSD RC Scale Rear Hubs (Black) Part#: SSD00178 www.amainhobbies.com/ssd-rc-scale-rear-hubs-black-2-ssd00178/p671638

Thank you for watching. Yeah this is one my nice looking rigs.

Thank you for watching. I installed the 6 inch Vanquish light bar. It is 152.4 mm.

@@henrysrcgarage5210 👌

Thank you for watching! It is much appreciated. For the traxxas pro winch, I do not own one of these at this time so not sure after watching a few videos on people installing them if they can be setup like the RC4WD winches using the wired controller. I do currently use RC4WD Warn or Reefs RC servo winches and do hook those up to the receiver to control them from the transmitter. The traxxas light kit will have its own module to regulate the power and will only connect to the receiver power/battery port. It's been a while since I installed one of those and mine are on all the time when I plug in the battery. Think if you want to control the lights with the mt12, maybe look at the MyTrickRC light kit for the trx4 version you have. I know it's probably not what you're looking for, but I do hope it helps you a little in maybe in different options.

Thank you for taking the time to watch. Yes, trying to make is as scale as I can, 😀

Thank You for Watching. When I first got the MT12, I realized Trim 3 and 4, when I was trying to program the overdrive servo on my Phoenix Portal, were momentary and if i did a sticky they were 2 postion. For my overdrive, it gives me a free wheel option and only goes rear wheel drive if I want to with the 3 position trim option.

Thank You for Watching! It is much appreciated.

Thank You for Watching. The cost for the setup I have in my videos is not cheap and is around $1200 or so which included what I already had in hand. I started collecting parts about 6 to 8 months ahead of time but already had some parts in the spare parts bin, the 4 servos, sound box, esc + motor combo, light bar for example I already had from the spares I had from previous projects. I am sure just getting the CEN Racing F450 Dually and a plow maybe enough and cheaper by about 600 bucks but really need better tires to get some traction. Thank you for asking.

You did a magnificent job with this truck. Would love to have one of my own um. Just to give to the kids, so they'll clean the driveway. If you know what I mean , l o l l o , l , it'll be my twice , but I'll let them use as long as they do not destroy it

Thank You for Watching, it is very much appreciated. 🙂

Thank You for Watching. Yes it is awesome but unfortunately 2023/2024 has fail to give snow, 😢. Hopefully 2024/2025 will bring some, 🙂

Thank You for watching! I put in the Castle Copperhead ESC when I removed the Spektrum 2 in 1 brushed smart esc. You can watch my earlier video of what i replaced the stock electronics with here: ruclips.net/video/qMeH4ss1F6g/видео.htmlsi=j74cT4fg_cHP7LF9

Thank you for watching. Yea I hear you. We only got a few inches of snow this year and it was really wet. I like having the rc plows and snowblower to remove snow. It keeps me out of mischief, 😆.

Thank you for watching. Yes it is. I cannot stop looking at it 😍