Видео

You did a good clear job of explaining timing adjustment. I always say hook point to neeldle clearance is no light between them without them touching each other. I think it would be good if next you would have explained adjusting the needle guard. With these tight tolerances, any side needle deflection and good bye hook point. Just for added thought, most of these machines are old. Cup screws get worn as well as other parts and normally they have been worked on by many people of different skill levels. If you've owned a machine a long time then you know its condition. If you've recently acquired it, best to go through it. These are tools for doing real work. Don't want any downtime.

Hello there guys! I have a direct drive motor on my Juki 8700H heavy duty model it’s 1000watt eBay direct drive I installed myself overpowered for that machine I’m sure. I would like to put that motor on my Juki 1541s but the Juki 1541 shaft is bigger and I would need the proper shaft collar for the 1541 not sure what size that shaft is or what that shaft collar is called or how to order one I could use some pro advice for that. Also they claim those motors are for light duty machines and maybe medium duty it is 1000watt though would you say that would work for the application I want to use it for? Main reason is I would like to get rid of belt altogether I have a regular 750 watt servo on it now. Thank you for any advice you could help me with and sorry if I rambled lol

Thank you so much for this video super informative

Question, at the end about the walking foot…I’m wanting to raise the rear foot a little when it’s in the down position. It dents the leather as I feed it through and I think if I can raise that rear foot it’ll resolve that issue. How do I raise that?

My new 0303 D machine stitch length was on 5. However, the dile - knob was very tight. I didn't use forse, instead, I unscrewed the knob mechanism which apeared fine. Problem is the stitch length is stuck on a long stitch about 7mm long no matter what number I set the dile-knob on. Can you help please?

Thank you so much!!! I really appreciate your detailed explanation and close up video! You’ve saved me loads of time and repair bills!

Hi there, thank you so much for the video, I just purchased a ikonix KS 335A which looks just like yours. I'm running Nylon 69 as this was recommended, but the thread keeps on unraveling and birdnesting on the bottom, any help would be greatly appreciated. Thank you 😊

Cómo montar artillería máquina triple arrastre singer 211

كم الثمن يود شحن الاسكندريه

Great job what I was looking for. Ty

Hi thank you for your video, very useful. My stitch button isn’t entering the groove of the eccentric mechanism.. the mechanism seams to be off a little to the right. How can I fix that? Thank you in advance

Great video!!! Very helpful, thank you.

Outstanding! I wish this had been available ten years ago, when I bought my LU563. I haven't used it for a while, and it was not being very cooperative. Thanks to your video, I think she's purrin', again.

Where can one find the coils of that machine, thank you

Do you have a parts list to convert a 562 to a 563?

Great video, it's been a big help. I didn't notice you mentioning anything about the oil level in the reservoir for the hook assembly at all though. And isn't there any way to oil the mainsheet bushing by the hand wheel?

Great video. Thanks for sharing your knowledge with us. I just bought a used Juki LU562, and I hope to use these techniques to make my machine sew as it should.

You might be able to help. Ive tried to remove the bobbin carrier. I've removed the 3 screws but the bobbin won't lift out. I think there might be thread caught between it and it wont rotate.

Absolutely amazing thank you

Hello neil. Could you please do a video on how to set the stitch width and do a trouble shooting video. The amount of movement for my widest stitch and narrowest stitch is only 1/16” wheel movement. And it doesn’t seem right. There’s way too much room that’s not being used at all. It’s a singer 221u566a also. If I hold the button down and turn the wheel, it doesn’t have very much adjustment that’s usable. And my stitch should be able to go much wider. Thank you in advance.

Do you know where i can find a tutorial to change out the presser foot bar on the juki Lu-562

Sir , I have a Paff 335, very recently I had a problem of tagging . When I pull down the tagging bar feeddog is not moving reverse. Please help me to solve that problem. Thank you in advance.

You just taught me things I didn't know I needed to know :) Very informative video, thank you sir!

Thanks for the helpful video! I bought a "non working" 111W155 to do my own upholstery on a car restoration project. About 6 hours ago I did not have a clue how these worked. I will keep the story short by getting to the punch line, which is there are two sliding cover plates on each side of the needle/foot area, which at first glance look identical, but turns out they are not. I am sure you are chuckling right now because you know what the important difference is. The upside is I needed to get familiar with the machine anyway and made all the little adjustments in your video, and after 6 hours of frustration it made me laugh too, when I realized that all I needed to do was switch those two plates around because one of them has a recess in the bottom of it so the thread can pass over the top of the bobbin case.

You mention at the end, lining the plunger up top with the button on the bottom up. Mine appear to be off now, what do you do to line them up? I was trying to increase my stick length for the first time and I think I goofed it.

Just what I needed. Thanks!

Why does my machine cut thread when it goes through takeup spring?

Could you please make a separate video on just the bobbin release finger? how to time and adjust the finger itself would be amazing.

You are The Man Neil. Thanks

Hey Good Morning! I hope you will be fine, Kindly make a descriptive video on Juki DNU-241. It should all setting of machine included. Thanks

Thank you sir. Great video .

Fantastic video. Can I ask how I slow the machine down. Minimal petal press and it takes off full speed. I have slacked the belt and taken the take up on the clutch lever and pitman arm to the petal like you showed in the video. The machine runs too fast

Hi! I have the same sewing machine just different brand but exactly the same set up. I am having problem with the thread coming out of the take up spring all the time (that spring after the tension before looping to the lever) when I try to stitch on fabric. Have you experience something like that and if so, how do you fix it? I Would greatly appreciate any help. Thanks in advance.

hi how i can delay the needle bar in my 211u165 because is arriving before the presser foot?please thanks

Ty for onother tutorial, i see alot of parts in in difrent machine is the same, where do you find good quality parts if you have to replace something. Do you buy chinise parts or you buy original when you fix it.

Ty for video, where do you buy your parts?

Great informative video! Thanks for taking the time to make it! I have a Juki LU-562 and it vibrates at higher speeds. Is this normal? The counter balance looks like it is in the correct orientation with respect to the needle. Cheers!

Thank you, Neil. This is very helpful. I also have a mercury m 111 h sewing machine with the foot on the plate and I cannot figure out how to raise it. As you can see it is an older machine that my wife REALLY likes. Your wisdom and guidance would be greatly appreciated. I realize it is an old machine and you are pretty young so either way Thank you.

Pfaff kl-1471-751/11

I pushed the stitch length button to release my clutch from a jam, now the reverse lever moves when I try to sew. What is going on? Can you help me?

i have a singer 491 and just got it adjusted however I noticed the reverse works up to 6-8spi but literally nothing after 10 or more. Makes locking stitches a pain because it cause a ball of thread in the material unless it does it automatically 🤷‍♂️

What is the big spring screwed on the base of the sewing machine ?

Thank you so much for this instructional Video. I just purchased a machine similar to this and I am looking for a cording attachment that would be compatible with this machine. any help would be greatly appreciated

I have a juki lu 562 and i can not regulate the upper thread tension. It is so tight the thread frays at the needle. Any suggestions?

I'm a complete newbie to this and recently purchased a second hand industrial sewing machine for my projects and signed up for a course in upholstery. I purchased the singer 411 u967aa second hand but can not find any videos on it anywhere. Is there a machine that is very similar to this sewing machine? Thanks ☺️

Again awesome video, how do I set dlt to be in the correct position, I moved the letters before and I want to set the letters again in the correct position.

Thanks for your expert experience!! Nice to have a little direction to preserve and maintain a hobby machine.

Thank you for the video. Super helpful too .

Thank you it’s a big learning curve for me. I’m really enjoying reading and studying.

what is that small clear plastic container mounted on back of machine? no one has ever bothered to mention it!