Видео

Sounds ace👌🏼 Power and torque?

Is it possible for one of these to be built like a torque converter where it has a set of stators and rotors, with one forcing the fluid through the other for a more positive lockup effect?

Hey man thanks. I bought my teen son a 2004 Impreza Outback 5-speed, 156,000 miles. AWD of course. We didn't notice a whine noise, but it just started clicking or tapping around curves and acceleration. I can feel the tapping in the gear shift handle. And it seems it sometimes loses AWD grip when it taps. So I think the center diff is binding the output shafts sometimes. I found new ones with 2 yesr warranty for $185 on ebay, or OEM from Subaru for $600+ 6 or 12 month warranty. Any suggestions?

18 dec 2023 5:27 am est ( utc - 5 ) : thanks . just-now i finish-seeing this movie for 2-nd-time . i forgot date-time during i see this movie for 1-st-time .

Hey where to buy fluid and how to know what fluid for a specific vehicle that says (non rebuildavle, even though they are dismantleable) Vehicule is a 2004 suzuki aerio. Thanks

These all rely on a mixothixotropic fluid that changes viscosity (thickens) under load.

Woot!, embarrassed that Mustang an he was on tire! Awesome job. Just read thru your build thread on HT. Don't go there much anymore, but damn, you show how to build AWD from scratch, lots of trial and error in there, way to go!

If the oil is low will it cause it to go bad or act like it’s bad?

Can you advise me on what viscosity silicone oil to put in a Honda viscous LSD? I want to rebuild/refresh it before putting my transmission back together. The fluids I see range from 30k to 150k. I read that Honda viscous couplers came with 30k but I can't find info on what the LSD came with.

boundary layer, Tesla turbine tech cool

Great video, exactly the answer to the question ”how viscous couplers work” that I had!

dsm had half the weight and the same if not more power. SMH we knew this would happen.

Hi, I'm in the UK and run a landrover freelander, my VC is solid! I removed it from the vehicle and you can put a large pipe wrench on either side of it, in other words one on each propshaft and it is solid! would a rebuild work on this do you think? Luckily I caught it before it damaged the transmission.

Is there anything you can do to upgrade them to work better/handle more hp......besides chsnging the fluild......and if you were to change the fluid is there something just flatout better?

Interesting.. So it acts exactly like a clutch--- accept its not a direct friction connection--- so the fluid still allows it to slip so that there is no binding from front to rear... Very cool.

Ben, What do you charge for a rebuild?

can you change the oil in couple that are sealed ? (subaru g3x ) ?

Hey buddy im looking to have my bmw e30 325ix VC coupler done how do I get ahold of you?

how much power did it make that the arp head studs didn't hold

We need more videos of this car and setup

Thanks for sharing. Very informative !

Why the fuck did you put a non VTEC head on a VTEC block

What vehicle does this coupler come from?

Theoretically, shouldn't you be able to tune the amount of lockup and when, by varying the thickness of the viscous fluid?

Can I get a sub back? I'm working on my rb25

Sweet have you seen the new speed factory trans upgrades forks n shims for the gsr gear set for the crv trans...also is your engine bay bed liner though of doing that for mine

B Series Transfer Case from Drag Cartel got first blood!!!! Killer Honda Build 4sure!

Where you able to find the tolerance specs?

Fuel cell in the trunk?

What power did you had here?

Post a video of the Milwaukee breaking loose that tack welded shift selector bolt

WRD FTW

Great information can I ask what was the max you pushed the crv rear diff to power wise?

Very informative. Content I would like to see: Floor it 😍

SHO needs the Livernois tune

slip details??

i have the same setup bro . how much power did u make?

help me

hey I have the duratrax raze as well .. I need help with the setup .. I have a 10th scale motor with a 8th scale conversion pinion and made a custom motor mount . please help ASAP

hey I have the duratrax raze as well .. I need help with the setup .. I have a 10th scale motor with a 8th scale conversion pinion and made a custom motor mount . please help ASAP

how much power

It is ok. The wheels are cast and the assembly is balanced after it is assembled.

Typical Honda owner at the end. Just because he lost the sound off to a SRT-4 he had to gas on it leaving. #ToMuchRice

Hi there,,,,I am about to do the same conversion! Are you still happy with yours?

I raced a stock slash with the titian 21

Are you ever in MD at the drag strips? I usually go to Cecil or Capital. I almost never see other DAs at the track. And what are you tuning with, Hondata? That sounds like you programmed you 2-step with ignition cut, I'm on Crome and it's much slower(fuelcut)

*Honda S2000 joins...Everyone wets themselves, then they all go home embarrassed.

4 gear ls trans

yo ben, youre cute

@76plymouthscamp To be honest, your better off getting a cheap brushless setup. Like EZRUN or a feigao motor and Mamba max pro.