- Видео 27
- Просмотров 66 582
CelesElements
Южная Корея
Добавлен 28 авг 2019
This channel is created for RC related stuff.
Especially 3D RC helis, fixed wing, FPV and RC electronics.
I hope to share my experience with you.
Thanks.
Especially 3D RC helis, fixed wing, FPV and RC electronics.
I hope to share my experience with you.
Thanks.
fail, fail, SUCCESS!! ZOHD AlphaStrike 620mm 136mph HD footage
airframe : ZOHD Alpha Strike 620mm
Motor : Brotherhobby Avenger 2808/1500Kv
ESC : Hobbywing Xrotor micro 40A(discontinued) // Lumenier 51A for telemetry
Prop : Schulze luftschrauben Super-S speed line 6*6(6.5*6.5 is better than that)
Servo : Blue Bird BMS-125WV // KST MS325
FC : matek F411-wse + INAV 7.1.0
Battery : 6S 1800mAh or 2200mAh
Motor : Brotherhobby Avenger 2808/1500Kv
ESC : Hobbywing Xrotor micro 40A(discontinued) // Lumenier 51A for telemetry
Prop : Schulze luftschrauben Super-S speed line 6*6(6.5*6.5 is better than that)
Servo : Blue Bird BMS-125WV // KST MS325
FC : matek F411-wse + INAV 7.1.0
Battery : 6S 1800mAh or 2200mAh
Просмотров: 206
Видео
AtomRC Dolphin 188MPH 303km/h 12S 50.4V setup
Просмотров 6 тыс.28 дней назад
airframe : AtomRC Dolphin 845mm Motor : BrotherHobby Special Edition V4 32.5-12 580Kv ESC : Flycolor X-CROSS HV3 80A Prop : Schulze luftschrauben Super-S speed line 8x6 Servo : Blue Bird BMS-125WV FC : matek F411-WSE INAV 7.1.0 Battery : 2 of Tattu R-Line 6S 1400mAh The motor and batteries are a little bit heavy. For saving the weight, I'll replace motor, prop and battery in below. - motor : am...
THEER wing Speed Run. Re-released by AtomRC
Просмотров 855Месяц назад
airframe : Skyzone THEER discontinued, but newly rebranded & released by AtomRC Motor : Xnova 2208/1500Kv ESC : Hobbywing Xrotor micro 40A(discontinued) Prop : Schulze luftschrauben Super-S speed line 6*6 Servo : Emax ES09MD FC : matek F411-WSE INAV 7.1.0 Battery : 6S 1800mAh 150g weight was addded for C.G..
RC FPV Green bottle BOMBER
Просмотров 2,2 тыс.Месяц назад
Airframe : XUAV Skysurfer Motor : Brotherhobby 2806.5 / 870Kv Prop : MasterAirscrew RS 6*4.5 ESC : 6S 40A generic Servo : KST DS113MG for elevator, Emax ES9052MD for ailerons FC : Matek F411WTE INAV 7.1.0 GPS : RushFPV M10 VTX : RUSH Ultimate Runcam DVR Camera : Runcam Pheonix, Foxeer 1200TVL Razer nano for bottom view Battery : 8S 5000mAh(EB-BG908ABY cell) 4.4V/cell, max 35.2V RC link : ELRS@2...
ZOHD AlphaStrike, atomRC Dolphin, THEER Foam Wing day
Просмотров 1 тыс.Месяц назад
ZOHD Alpha Strike 620mm : max 254km/h Motor : Brotherhobby Avenger 2808/1500Kv ESC : Hobbywing Xrotor micro 40A(discontinued) Prop : Schulze luftschrauben Super-S speed line 6.5*6.5 Servo : Blue Bird BMS-125WV FC : matek F411-wse INAV 7.1.0 Battery : 6S 1800mAh AtomRC Dolphin 845mm : max 272km/h Motor : Brotherhobby Avenger 2808/1500Kv ESC : Racerstar tattoo 52A(discontinued) : It has been repl...
VBar NEO + ELRS Gemini + EdgeTX, FBL heli setup
Просмотров 1432 месяца назад
Model file is here : github.com/DongkwanYi/VBarNEO-ELRS-EdgeTX
RC MotherShip inspired by Virgin Galactic
Просмотров 7012 месяца назад
Sir Richard Charles Nicholas Branson, Elbert Leander "Burt" Rutan, Burt Rutan! Go Virgin Galactic! Airframe : XUAV Skysurfer Motor : Brotherhobby 2806.5 / 870Kv Prop : MasterAirscrew RS 6*4.5 ESC : Hobbywing micro 40A Servo : KST DS113MG for elevators, Emax ES9052MD for ailerons FC : Matek F411WSE INAV 7.0.1 GPS : RushFPV M10 VTX : AKK Ultimate 2W runcam DVR Camera : Runcam, Hawkeye DVR Battery...
Improve Tactile Feeling Radiomaster BOXER
Просмотров 6222 месяца назад
Improve Tactile Feeling Radiomaster BOXER
Building battery pack for FPV wing using phone battery
Просмотров 3902 месяца назад
The batteries below is recommended for long range flights. Support 45W charging batteries EB-BN972ABU (for Samsung Note10 , 4200mAh) EB-BG988ABY (for Samsung S20Ultra, 5000mAh) EB-BG998ABY (for Samsung S21Ultra, 5000mAh)* EB-BS908ABY (for Samsung S22Ultra, 5000mAh)* EB-BS918ABY (for Samsung S23Ultra, 5000mAh) : marked "*" are recommended. Consider lifecycle of cell phones. Support 25W charging ...
OLED mod for Radiomaster BOXER follow-up
Просмотров 5 тыс.2 месяца назад
*firmware&info : github.com/DongkwanYi/OLEDBOXER *parts list OLED : 2.42", 128*64, SSD1309 compatible driver, SPI interface cable adapter : 0.5mm pitch, 12pins flat cable : 0.5mm pitch, 12pins, same side contact, 50mm length *parts links OLED : www.aliexpress.com/item/32950307344.html?channel=twinner cable adapter : www.aliexpress.com/item/1005004411740279.html?channel=twinner flat cable : www....
Two concept designs for Radiomaster POCKET
Просмотров 8 тыс.8 месяцев назад
Conceptual design, not intended for real use.
OLED mod for Radiomaster Pocket
Просмотров 7 тыс.9 месяцев назад
Firmware and all info for mod : github.com/DongkwanYi/OLEDBOXER 1.54" OLED : www.aliexpress.com/item/32971511348.html?spm=a2g0o.order_list.order_list_main.49.54711802A8Afsy Adapter board : 0.5mm pitch, 12pin. www.aliexpress.com/item/1005004411740279.html?spm=a2g0o.order_list.order_list_main.31.54711802A8Afsy film cable : 0.5mm pitch, 5cm length, 12pin, same side contact. www.aliexpress.com/item...
OLED mod for Radiomaster BOXER
Просмотров 12 тыс.9 месяцев назад
All info for mod is here : github.com/DongkwanYi/OLEDBOXER
Baby AR Wing PRO 682mm, 117km distance setup!
Просмотров 5 тыс.11 месяцев назад
Baby AR Wing PRO 682mm, 117km distance setup!
SHIZUOKA HOBBY SHOW 2023 : AIR RC related
Просмотров 415Год назад
SHIZUOKA HOBBY SHOW 2023 : AIR RC related
Supper kumpel. Einfach gute arbeit. Leider kann ich kein englisch aber versuche durch deine videos die detailiert gemacht werden es zu verstehen. ❤
(google translate) Vielen Dank, und ich hoffe, es hilft Ihnen. Wenn Sie sich die Datei auf dem Link in der Beschreibung anschauen, können Sie sie einfach benutzen und ich denke, es wird hilfreich sein. Mein Neffe lebt in den Niederlanden, und es ist sehr schön, so einen Deutschen zu schreiben. Ich weiß, dass Deutschland und die Niederlande Geschichte und Sprache nahe stehen. Es gibt sowieso nicht viele europäische Kommentare, vielen Dank für die Mitteilung! Wenn es ein Missverständnis gibt, bitte verstehen Sie die sprachlichen Unterschiede! Thank you very much, and I hope it helps you. If you look at the file on the link in the description, you will be able to use it easily and I think it will be helpful. My nephew lives in the Netherlands, and it's very nice to have a German write like this. I know that Germany and the Netherlands are close to history and language. There aren't many European comments anyway, thank you for the communication! If there is any misunderstanding, please understand the linguistic differences!
is a nice video, please remove the orrible music...
Oh, I'm sorry about that. It is late to remove the music, next time, I will choose a good music.
Hi, What is the autonomy?
Please refer the description. airframe : Flite Test Bloody Baron 737mm motor : Xnova 2204/2350Kv prop : HQ 7*4.5 battery : Sanyo NCR18650GA 3500mAh 2S1P PV cells : claim to sunpower maxeon C60 1/3 in serial blocking diode : TI SM74611 FC : matek F405WMN + INAV 6.1.0 radio : Boxer + ELRS(betaFPV SuperD)
Just a personal preference here. I’d rather get my hand cut by the prop vs my head cut or eye taken out doing an over head throw.
You cannot see the real GPS speed while diving, there is not much advantage in doing 12s. It is possible to reach these speeds with 6s and a high pitch propeller and a high kv motor . good flights
Thank you. Honestly I have a fantasy about high voltage. I think 12S seem to have an advantage in maintaining voltage(less Vsag).
I prefer concept 1
Thank you for comment! I like concept 1, too!
and in general this esc definitely has telemetry. and I'm not sure but it seems to have a current sensor, so in the settings this can be configured if you connect the TX esc to the flight controller
Thank you! I'll check it!
Friend, according to my calculations, this configuration has reached its limit, why don't you try tmotor 3115 1050kv-900kv with 6inch propeller 12s 900kv - 6 inch prop 12s 1050kv - 5.5 inch prop
Thank you for advice! At initial setup, I refer the performance FBL helis, it run 12S and around 500Kv motor. I'm testing it by increasing the motor Kv little by little. In my opinion, the 3115 motor is a little bit heavy for my configuration, I want it to be less than 100g.
@@celeselements then it makes sense to consider RCINPOWER AOS Supernova 2807, as they say this is one of the best engines, but it has 1400kv so it will have to be used with 8s
Silicone 30awg is fine? Worrying about this lol. I also dont get why detaching the panel at 2:50 is necessary? Cant I solder on the wires with it still on or will there be alignment issues? Mine has headers on the side
I think AWG30 is fine for this purpose. The reason for detaching the panel is to align it with TX's front case. The pin header need to remove for dimensional interference.
You can change the fan with a better one, I reccomend GDStime 4007 5V
Wow, Thank you! That's what I was looking for!
Launching overhead like that is human error. When you hold it vertically flight controller will try to level the plane and it will overshoot the correction after you release it. The right method is to throw horizontally into the wind or slightly nose up.
I'm happy for laughing at my video! My auto launch angle is 45 degree, I can't meet the degree. I think your last sentence is golden rule of launching. I need to practice overhead launching because sometimes the airframe is built very heavy for long range flights
did you try to throw it from the tip of the wing?. I think is easy and safe. Try from the left wing with your right hand to compensate for the torque of the motor
I think sling shot is hard for this shape of plane. This is because the heavy parts - battery, motor - are dispersed far from the CG and long plane length.
Can I use a 1.3" or 1.4" OLED screen? Can OLED screens with built-in I2C be used? The mod code can be used for ELRS and CC2500 versions, right?
Check the OLED driver. The OLED should be compatible with SSD1309 and SPI interface. I2C is not supported. The display is independent of RF system.
Hi could this work with radiomaster ER8G? Thanks
Yes, ER8G is good enough to use on helis. But it didn't support gemini mode.
@@celeselementsthank you
Just droping the charger like this and the end It´s like saying F*** P**** of S*** go F*** your self a thousand times LOL
Thanks for watching!
And the speed is not count as a dive, u only take the real speed when the plane is level and running a full throttle for 300/600m
Yes, right. I think a dive is cheating for a number. I'll try for 200mph at level run!
" I try again" You sir are a true hero
Thank you! I get energy from someone like you!!
Flies while EW is not there
Can you show in a video how the Bottle is attached to aircraft?
Analog video is dead
Yes, but I'm still happy with it.
XD
Nice work. Not any easy plane to make fast but you did. Try the heewing F01 next.
F01 seems to be a speed machine, I'll think about it.
i mean cool the setup at 12s, but whats the point on going 12s to only get to 188mph? a goblin will do better than that at 6s (2814 2000kv 6.5x6.5)
12S have better voltage sustaining under load than 6S. Strix Goblin is also cool!
Why do you care what someone else does with their time
Thumbs up
Thank you!
Very cool video. Your current measurement seems to be very low; 0.6A?
It’s because he’s running the esc straight from the battery so the fc can’t measure current draw from esc
Hello, I like the idea, a question, how do you use this engine with 12s, if the manufacturer says for 6s. It doesn't heat up, what consumption does it have
I didn't check the current. Typical performance FBL RC helis run on 12S and around 500Kv motor, I referred to it.
Its not 6s when u combine 2 6s together, only thing will be added is the total mah oh the battery,
Hello, yes now, 6s is parallel, not series. Thank you
Tape ?
Tape to prevent hatch drop at high speed.
Cool, what is that software, is it on github, did you use to map your telemetry and speed from I assume edgetx SD logs?
Thank you! Set SD log on your TX(special function) and get telemetry file, And drag and drop on otxui( maxbl4.github.io/otx/index.html ). Check the keyword "otxui".
Where is the code?
Please check the description! github.com/DongkwanYi/OLEDBOXER
Why is your OSD flickering? Grounding issue?
My camera was the cause. After replacing camera, flickering is gone.
It looks like it gets some airframe flutter at higher speeds, have you thought about coating the wing with fiber reinforced packing tape under the outer film? More stiffness can't hurt!
Thank you for advice! Several methods are being considered for reinforcement.
Amazing!
Thank you!
Sweet!!!
Thank you!!!!
Dropping water balloons might be fun. Adding streamers could make dropped items more visible.
Cool idea! The drop scene isn't shown well.
@radiomaster Should hear this improvement 😁
Thank you!
Fantastic video!
Glad you liked it!
I do kinda the same thing, parachute taped to bottle😅 Kids love it, cheers from N.Y😊 very cool release set up.
Thank you! Parachuted bottle is COOL!
Your autolaunch idle throttle seems low and your launch throttle high. Going from almost no torque to huge torque. Getting the two closer might eliminate your crazy launches.
Yes, my idle throttle is 1200, I'll try more idle throttle at next time for your advice.
Do you think it is possible to change the internal module from 4in1 to elrs… I purchased a 4in1 boxer by mistake and now I can no longer return it. I'm thinking of getting INTERNAL RF ELRS from the radiomaster site, it seems to be simple and possible to reverse them
I'm sorry to hear that. I sometimes make order mistakes, too. It is not possible to convert the 4in1 into ELRS. You can find many tutorial youtube vid of exchange module, and it is easy!
@@celeselements so by buying the internal RF ELRS module and changing it everything works without having to buy an external one!!?
Thank you for this video. I love this idea. Would really love modding a Radiomaster Pocket with an OLED. Will the process be pretty much the same for that?
Basically they are the same. Only difference is a physical apperance.
@@celeselements Thank you. That sounds reassuring. I found a 1.54" OLED display which I suspect is correct for the Pocket. I assume it requires the same board and flat cable? The flat cable link is dead, unfortunately.
👍👍
Thank you!
Nice landing !!
Thank you!!!
booom
Thank you!
Camera switcher is so cool!!
Thank you!
Sorry Sir, How do I show the clock on the main screen ?
It is a EdgeTX feature. Try 2.8.4!
You are not a friend of Soju..... you are not a friend of mine!!!!!!
I'm a Sailor, I had my fair share of Soju and bad women. Airplanes keep me out of trouble.
Good Airplane. No more drinking Soju. Soju bad, Airplane good times.
hello friends, my LCD has a screen mirror. Can you make more firmware for the one that doesn't mirror the screen? please help me guys.
I use a 1.3 inch Oled V2.0 LCD, Branded by Adafruit Industries
github.com/DongkwanYi/OLEDBOXER/tree/main/firmwares Check README and firmware!!!
@@celeselements thank you my brother I will try it.
@@celeselements For OLED Pocket there are 3 updated models. and the first thing I tried to flash was using the model with the screen upside down. and I tested the function. the problem remains, namely the screen remains upside down with no change. and I tried flashing the other two firmwares. the problem persists. please help my friend.
I'm sorry it didn't work. There's no way I can help you any more now. Buy a new OLED and try it again. ko.aliexpress.com/item/32971511348.html?spm=a2g0o.order_list.order_list_main.49.54711802A8Afsy&gatewayAdapt=glo2kor
Hi, can this tutorial be successful by just following your video? Coincidentally, I want to replace the LCD for my Radiomaster Pocket Remote. or you have to follow the tutorial in the link in your description, such as creating a Gitpod for compilation. and others
Yes, you can do it. I uploaded firmware for Pocket. You don't need to compile it. I uploaded everything for mod at my github and youtube vid.
@@celeselements I have installed it but the screen display is upside down, what's wrong?
@@celeselements hello friends, my LCD has a screen mirror. Can you make more firmware for the one that doesn't mirror the screen? please help me guys.
@@celeselements I use a 1.3 inch Oled V2.0 LCD, Branded by Adafruit Industries
@@GarengPetruk Please wait a few days. I'll find a way.
Nice...
Thank you!
Hi, what is the ‘UgliderINV’ screen you gave setup? Looks interesting and I would like to try it on my boxer
Yes, It is my model name. Ugilder and INAV setup : ruclips.net/video/1nyaZPlXg9s/видео.html If you want to change the model name, MDL->choose the model and go SETUP 2/12.