Видео

Ok

Me gusta

Its called Florestone Wedge Lock 2inch version. I got it from Rampart Supply in Colorado. Since mine is already leaking, i use 2 long nose plyer to pull them up, one on each side. Then i make sure there's no debris around the 2" pipe and out side. Then I use soap to wet the gasket really good and also get the soapy water outside of the 2" pipe and it slide in with no problem. Then I use a rod to push the rubber gasket in really well to make sure there's some sort of compression . Ran water test, hot , then cold, to make sure its dry.

Is there a chance you could bounce the camera around a little more. :-/

If its level and solid when you dry fit then dont use motar.

Thanks

Great video….. no talking just doing!

Thank you so much!!!!!🎉🎉🎉

Great the instructions i got were terrible. Thanks.

-- Nice, no puller. Thanks!

Thank you so much! This box has been sitting in my corner catching dust until I found your video (ashamed to say). 😭🫶🏽 Happy Holidays!!

Me salvó de todo 🧑🏻‍🏫😂

hola tengo uno y el lado de oxigeno esta tapado y no sale nada alguien tiene idea como se limpia o destapa gracias

Hi I bought this from a guy that resells Amazon returns. I did get it assembled with no instructions but before plugging the wheels into the battery I wanted to make sure I had the polarity correct and the wheels in the correct locations so I looked up this video just to learn that it should have come with a remote to steer and control the gas & brakes! It's also is missing the power cord to charge the battery. How can I find out where to buy the remote and power cord? Any suggestions are appreciated! Thank you!

Awesome 👏

Koun sa site hot hai

Where did you buy that bit?

The water level in the bowl is super low, same as mine. It's causing solid matter to stick to the sides. A pain for maintenance. I tried clipping the fill hose inside and outside the overflow tube but it made no difference to the water level in the bowl. Too bad.

I can install this, right? Yes? Yes. I can install this.

ভাইয়া এই জিনিসটা আমার খুব দরকার বাইক মডিফাই করার জন্য এটা দিয়ে কি লোহা কিংবা সিট কাটিং করা যাবে কিভাবে অর্ডার করবো

Fantastic video. Just installed one of these and I thought the design is stupid that the supply lines are in the subfloor! such a stupid design.

WRONG!! Cap goes on FIRST, and o-ring is missing which is supposed to be installed in escutcheon holder. RTFM!! DO NOT FOLLOW THIS VIDEO. He's missing the o-ring. And if you try to push the cap on after the estucheon plate, you may end up pushing the o-ring back inside the channel OR break off the chinsey little plastic tabs (which is what happened to me when I did in the wrong order, like this guy is showing).

Need shock arresters on a washer box cold and hot

Part Name: Wedgelok. Get at any Plumbers Supply house. Use a screwdriver to wedge it out. Put it between the outside PVC and push and wedge out. Go all the way around a few times, comes out in 1-minute. Next clean between the opening. I used a wet paper-towel and a screwdriver all the way around. Repeat until towel is clean. Lube up. I used K Y Jelly inside the wedge area all around, and put it on the inside of the new rubber wedge and outside. Make sure top which is the flat side with 2 or 4 indentations is on top. Round side goes down. Push it in, then help it with two screwdrivers pushing on top about a 1/2 inch away from each other all the way around. Then I used a full roll of black electrical tape, put it on top of the wedge, and stood on it. Clean hands and tools. Finished.

Annoying music!

Only this worse then this trash valve is the know nothing plumber that would put it in

Need words

Great video 👍

So easy even a cave man can do it

I have a job coming up that requires drilling holes into 2" bluestone stair tread slabs. Did you just use a regular hammer drill with masonry bit? or a diamond rotary bit?

What a crappie video

How did you secure the posts?

Como le haces para reparar uno ya viejo?

Thank you! Very helpful, unlike instructions for stair railing from deckorators__TOTAL BS!! Why would I shorten one top rail over the bottom rail when they're parallel to the post to begin with!!!

Where can buy this stuff. Please share Tq

cool im gonna use one for a rocket stove

Thanks for the share

How we buy in India pencil tourch

Thank you , but It would have been much better with narration

Great job, and the bathroom looks amazing. How did you tighten the bolts though? Did you reach around back, or did you have to work through the little holes? I just ordered this toilet and am waiting for it to arrive at my local Home Depot. Most of the skirted toilets are chair height, so I was very happy for discover this model.

Please... burp or fart for gods sakes. You have audio recording.

I hate this type of rubber gasket. Seems guaranteed to fail and you may never know in a slab condition.

I have a slow dripping leak on this model. What is the part number to replace the cartridge?

Hi, can you link the black waterline and additional parts that you used please?

The way how the faucet is connected to the countertop looks extremely flimsy. Bad design from Moen. I bet the whole construction with broke from the very first careless touch....

Hola Santo Domingo Rd Que Cuesta en Dollar

Very nice!!

Que marca es esta bace

This add is all lies wake up

Super! I like that you used the Toggles for the install the toilet seat. Our plumber did not and used plastic screws. I need to replace the seat. I can't get behind the skirt Toto Aquia III - CST464MF. I see no way to get access to the nut under the bowl flange without removing the toilet bowl and would prefer not to do that . The back of the bowl is almost flush with the wall behind it. There must be an easier way, right? Any ideas? Can I simply remove the plastic screw and then use the toggles. I think the part number is (THU651N)?