Видео

RUclips saves the day again

It would have been helpful to fill in the extra space with a small backer rod or small piece of wood. That will help reduce the chance of the bondo cracking at some point. Also, you sanded the paint on the baseboard to exposed MDF. If that paint isn’t oil based, you may have swelling.

What's wrong with using drydex? Dries super fast and needs no primer. Great work though, you didn't settle for the terrible job before!

Excellent video👍😎🍻

You should use a multi tool to cut the bottom of it off level with the base afterward. Looks good though

Don't need to use that much tape and time. Use wet sponge will be seamless

The bondo must not have worked that well because there is no Before & After pictures lol. Where is the final result on this video it's not there.

What were the size of your blanks that you used to glue up? 2” x 1.2”?

You maybe fitted a base block if you know what that is freind it sets the skirting and facing nicely

Nice you just saved me a trip to HD to buy a jig!

Hey when did you use the Cream Hardener?

No need for apologies. Your face isn't that important.

Graco Paint Sprayer 🤟

Worst part of the job makes me want to quit

You aren't wrong if you don't know. You are only wrong if you are enlightened and choose to disregard it. Mistakes are something we all do but sometimes it's ignorance that leads to mistakes.

Ha. The ending was funny but honestly I wish people would show the aftermath of something if you didn’t follow the tips like you did! Great video.

Stop moving the camera!!!!

nice build... I was wondering doe the kits came with the piece between the headlight n grill?

I want to make something like this for my kitchen instead of polyurethane. Do you recommend using something else instead to make it good for food?

This is what I wanted for my bathroom. My question is.. did u just put out in top of your vanity? My concerns is if it gets wet. How do u deall with this?

Same process for floor?

Mine is over 3 years old. Lots of use. No use over summer, lots of slime build up. E02 error would not stop after simple cleaning. Almost threw it away and bought a whole new one. I had to disassemble entire unit and remove the pump. Not too difficult. Required a very long and slim phillips head screw driver. Deep cleaned the pump, found nothing broken. Reassembled everything. Deep cleaned the hot tub. Brand new filter. Filled back up with fresh water. It is working fine now. Hoping it will last the entire winter here in Florida. Cannot find a replacement pump online. Cannot buy just the electrical/heat unit by itself. Fingers crossed.

What about the depth of the holes you drilled? Is that not important?

do you use that pump armor stuff they push for storage? seems like it's not needed.

So you had to empty the tub? That will cause a high water bill. I hope it's just my filter... 🙏🏾

Mine stops spraying after a while. Stays runnin and I have to reset it a few times. Is awful. I wonder if this happens when the paint is low in the pail.

Great video, going to build a custom desk using this method.

Or ... glue a small piece of same or similar trim piece. Give glue 20min to dry. A little bit of dynapatch. Light sanding. Paint. And Bob's my dad's cousin ... cause he's not my uncle. 😊

How are these holding up? Thinking about using these to redo my kitchen.

What was the type of wood used for this project?

What were the size of the cabinet doors?

This is great Ben! Nice work. How would you modify this build out if you didn’t have the side walls? How long did this take you?

If you use expanding foam before the filler then trim it once dried, it uses less filler. Also I use expanding foam on the skirting board and for trim to fix it to the wall.

What color paint do you use after repair? Looks like a great match - I'm struggling with this part. Thanks

Yeah it’s never pleasant seeing a shrunken caulk is it that’s why I always buy the one that says I’m a shower not a grower and problem solved 😂

Where did you find this door? Looking for sizing for our new build

all goods product nice 👍 goods idea love its

Overkill

Hi what grit are you using? @ben.builds. Thanks for sharing this video.

Very well done. Thank you

Should be called “converting an 08 to a 2015 lol”

You should do more videos, very thorough you could be on of those RUclips famous contractors. Keep it up. And just look at what’s trending good luck 👍

Excellent video --- real thorough and also concise. I'd seen several others that were more of an unboxing type, and I think they just didn't have the same air of authenticity that this did because you'd done the setup before. Thanks for putting this one out!

It’s a butcher block cause of the style of it ? Cause in world would it make sense to make butcher block out of pine. But if it’s for garage use only it’s cool

On the side of my table it's mdf I discovered after removing the paint layers. However it's swirled colors on paper. I tore a piece off side and it looks like mdf. Can I glue it with carpenter glue or kray gluez?

What’s the name of the buffing product and waxing product

What about scratches going dif directions from the grain using sn orbit sander?? Akso do u use it on a slow or high soeed i ua r a deeal varuable speed

Would have liked to see the end result. BLUE BALLS.

Honestly i thought it looked better before sanding than it did after

What about the doors