- Видео 21
- Просмотров 254 578
SA2CLC
Добавлен 21 май 2016
Utracer v6 tube tester
Quick look at my Utracer V6 that I´ve built.
Also a quick demo of the Utracer software.
Had some issues with low audio quality, sorry for that
sa2clc.blogspot.com/2025/01/utracer-v6-vacuum-tube-curve-tracer.html
Also a quick demo of the Utracer software.
Had some issues with low audio quality, sorry for that
sa2clc.blogspot.com/2025/01/utracer-v6-vacuum-tube-curve-tracer.html
Просмотров: 271
Видео
Vintage SSB station. CE20A, 813s, and Collins receiver
Просмотров 632Год назад
Thanks for checking out my stuff. I have recently got this old Central Electronics 20A on air after a bit of repairs and aligments. Puts out about 10-12W, feeding an old (70's built) dual 813 linear. Skip ahead to the tune up and the QSO´s if dont want to listen to me talking. Thanks for watching
ARC-5/SCR-274n receiver power supply
Просмотров 1,5 тыс.Год назад
I´ll give you a quick look of this newly fixed BC-455 and it´s power supply. For more info, go to: sa2clc.blogspot.com/2023/02/arc-5-receiver-power-supply-in-depth.html For the tuning knob, here´s the link to thingiverse: www.thingiverse.com/thing:5830104
20m AM qsos using Collins ART-13
Просмотров 1,5 тыс.Год назад
Don´t be limited to 80m AM with your older gear. There´s almost always someone on 14330 or thereabout. In this video I´m using my Collins ART-13 transmitter and Collins 75A-4 receiver on 20m. The transmitter puts out about 110W carrier, which does a great job getting into the UK from Sweden.
WW2 BC-458 40M CW QSO´S
Просмотров 9912 года назад
Put this old WW2 "command set" BC458 into service again. Had to replace 3 capacitors, and added a 900pf capacitor in parallell to the antenna lead to help load better into 50ohms. Puts out about 55watts.
CW qso´s Sweden to Japan
Просмотров 1,7 тыс.2 года назад
Casual working dx stations. Rig is Elecraft K3, linear amplifier is homemade, providing about 750W. Antenna is an EA-antenna hexbeam. Thanks for watching
Homebrew CW transmitter CW QSO
Просмотров 2,7 тыс.3 года назад
Thanks! This is a video of my homebrew CW transmitter, and also a cw qso. I built this transmitter a couple years of ago. Covers 80-40-20m with about 25w Built in an old BC-375 transmitter tuning unit inspired by late forties, early fifties articles. Has an 807 final. Enjoy
Elecraft KX2 hardcase
Просмотров 2,6 тыс.3 года назад
I found the perfect hardcase for my Elecraft KX2, which is roomy enough to let the KXPD2 paddle still be attached, yet small enough to slip into my backpack without taking up too much space. Case is a Seahorse SE56. Make sure to buy one without the rubber liner, or else the transceiver with attached paddle will be too large. The insert is 3d printed, available on my thingiverse page. www.thingi...
3D printed vacuum tube transmitter QRP CW QSO
Просмотров 2,9 тыс.3 года назад
Thanks for checking this out. Cw qso on a 3d printed tube transmitter. I wanted to make something on the ender 3, and I´ve had this at the back of my head for quite some time. used the simplest transmitter design using tubes as I could think of. designed a baseplate, coil form and a compression trimmer capacitor for frequency setting. Having a cw qso, as always with Finland, and also try out a ...
All tubes double sideband transmitter
Просмотров 1,1 тыс.3 года назад
Welcome. This video is about a DSB transmitter I built using only vaccum tubes. Disclaimer: it´s mostly me talking. I´ll give you a basic presentation of the transmitter, I´ll walk you through the schematic, and there´s a qso near the end. Many thanks for watching,
Arduino antenna rotator, antenna switch, antenna tuner controller
Просмотров 2,3 тыс.4 года назад
Hello, In this video I give you a brief overview of my antenna switching, rotator control and antenna tuning system, using one controller, which communicates with a slave located on the other side of my property. The reason I ended up doing it like this is because I did not want to run all those cables for antenna switching, rotor control, possible 4SQ control lines, and son on, from the "anten...
Cw qsos during straight key night 2021
Просмотров 4,9 тыс.4 года назад
Me using a bunch of old and some newer rigs during SKN and having qsos. First up is a Luftwaffe EK and SK, next up is a Swedish army RA200. After that is a homebrew affair for transmitter, and a BC348 receiver followed by two small qrp rigs. An lnr precision MTR4B, and a kit built soda pop 2 single band transceiver. The finale is the clunky ART-13 having a qso all the way to England on 80m. Hop...
3D printed multiband vertical antenna loading coil, tested at high power+ CW, SSB QSO
Просмотров 45 тыс.4 года назад
update nov 2021 VK1ERF has made a brilliant write-up on how to build and set this up. Make sure you check it out. digitalshack.org/?smd_process_download=1&download_id=762 Here is montage of me making a loading coil for vertical antennas from scratch using the Ender 3 3d printer. The coil form is printed in PETG at high resultion. I have desgned the coil using fusion 360, with inspiration from a...
Arduino semi-automatic antenna tuner
Просмотров 51 тыс.4 года назад
This is my Arduino controlled antenna tuner for ladderline fed antennas. It uses an arduino nano, which saves stepper motor positions, and relay settings to eeprom, for quick QSY´s.
Paraset WW2 spy radio replica morse code CW QSO
Просмотров 19 тыс.4 года назад
Here i´m showing my latest build. It´s a Paraset, a one tube transmitter, 2 tube regenerative receiver transceiver. This was a fun build, and I´m pleased with the result.
My grandpa had a big tube tester. Looked a little like that. Saw it one day and a huge box of tubes. I asked my dad what he did with that stuff. He apparently bult TVs for fun in the 50s and 60s. Took me a while to comprehend that....
Tommy. Nice build and great presentation. Tnx Peter/AA2VG
Thanks Peter
Cool mate
Nice. More tube videos and tube testing
Yes, will test a bunch magic eyes soon, will film that
God that Collins 75A-4 Receiver is nice! Engineering as art! Your equipment is in immaculate condition! I have shack envy!
thanks a lot
Hi there! Great video and just asking if you could please post a pic from the inside thanks.
(-.-.)( - -.- ) we use this code to call all station 😅
What a grand old radio set. Transmitter and receiver are works of art.
i had the collins rx before it blew a fuse.
DID YOU FINISH THE BLOG? i GOT ALL EXCITED VIEWING THIS VIDEO AND READING THE 1ST PART OF THE BLOG! TELL ME MORE!!!
Part 2 is now up
After having 3 348 I loved this video
It is very BAD receiver made by american Imperialists. Original have sensivity 10...20uV.
Yes, fun little receivers. I have 3 ARC-5 receivers and a matching power supply that a friend of mine built. I bought them when he had to move away. Very stable receivers. I'll make a video of them at some point. 73 Paul AA1SU
hi and thank you !. would it be possible to make a model with 12 radiants...?
Передатчик очень похож на советский Р-807 с автонастройкой. Были такие в свое время на лампах в выходном каскаде ГК-71, в модуляторе две лампы Г-811, возбудитель СВ, удвоитель, утроитель,учетверитель частоты лампы Г-1625. Возбудитель КВ лампа Г-837.Лампа 6П6С предусилитель НЧ. Усилитель подслушивания 6П6С. Предусилитель НЧ лампа 12Ж8. Звуковой генератор лампа 6Н9С. Кварцевый генератор и смеситель лампа 6А7. Для питания анодных цепей умформер У-600.Для автонастройки электродвигатель постоянного тока ДУ-40. Этот передатчик работал совместно с приемником УС-8, УС-9, РПС.
Так советский передатчик это его копия. Так же как приемник УС-9.
@erwe1054 Да, так и есть. Американскую лампу 807 тоже Советы сдули, приделали букву Г и получилась Советская радиолампа Г807.
@@МихаилМихаил-б6я И ГУ-13 это RCA-813 потом стала ГК-71. Много ламп ссср это полные копии американских.
@erwe1054 Гу13 это совсем другая лампа. Не путай с лампой ГК-71. Посмотри их параметры для сравнения и поймёшь, что это разные лампы. В некоторых случаях можно ГК-71 заменить на ГУ-13 , но при этом потеряешь в выходной мощности.Вот для сравнения несколько параметров этих ламп. ГК-71. напряжение накала 20вольт, напряжения анода 1500 Вольт, напряжение второй сетки 400 Вольт, напряжение третьей сетки 50Вольт, ток анода 250мА. Теперь лампа ГУ-13. Напряжение накала 10Вольт, напряжение анода 2000 Вольт, напряжение второй сетки 400Вольт, ток анода 50мА. Остальные параметры смотри в справочнике по электронным лампам.
@@МихаилМихаил-б6я Да ты прав, гу-13 не полная копия бит в бит но понятно откуда ноги растут. ГК-71 как раз ставилась в рсб чтоб кинуть накал на бортовое питание 27 вольт а гу-13 переработанный вариант с низким напряжением накала.
Fantastic engineering but couldn’t help smiling thinking that the stepper motor sounded like Dracula opening his coffin lid! Sorry
Это 5J
Скоро после ядерной войны пригодится!!!
Very nice build! Fantastic audio. Well done! I have made one too but have problems making the receiver work in the range required. Will keep on working on that. Why is it an infamous transceiver? I thought it was famous.... 73 and tnx. Rob. YS1RS
As far as I know, the life expectancy of those using it (resistance fighters) was not very high. I read of six weeks up to six months. Just google it! 73 and gl. Wolfgang, DK7NH
Now I understand!!! Makes total sense. Being this radio a Regen, made them easily detectable, as Regens produce a small amount of RF, even when receiving! That made them easy to locate for the sensitive Radio DIrection Finding equipment used by their enemy. Understood. Tks. 73 Rob, YS1RS
I like...
Why does it sound funny? I don't mean to be condescending, I'm genuinely curious why it sounds like that and not a pure sine tone
Hello. Will this transmitter work with unipotential cathode tubes (dual triodes with one large cathode spanning both portions, such as the 6Y7G)?
I would think so. Both cathodes are at ground potential anyway
Ja na odbiorniku BC348 zajalem first place in spdxcontest somb 1972 year. fb RX . 73 for all hams de SP9DTI
Can you provide a reference to the Swedish qst article, and a .pdf ; and a circuit diagram of what you have done ? thank you
Bra idé. Jag ska bygga den för mina WWFF- och Pota-operationer. 73s SA7LAV
What did you do with the crystal right before the QSO? I assume you matched your receive frequency with it, but I'm asking how exactly?
Correct. I have a single transistor oscillator built into the power supply used for "spotting" the transmitter in the receiver. Only thing is I'm not spotting the transmitter, but rather the crystal frequency.
Very nice radios you've got there and I really like the older radios from in the past they are very different and interesting compared to the modern radios we all have today. Thanks and best 73's for now cheers. Stephen M3SNV 73's.
hey, thank you for your stl file. I tried it on my Creality K1 and it works great. I use FreeCAD to create 2 cover plates for top/bottom to close it because of rain :-). I uploaded it on thingyverse. Thank you for your inspiration 🙂
Fantastic well done, Even got a contact love it! Thanks for sharing
Thanks, yes, a fun project. Have ideas to make use of the printer more, with swinging coupling coil, and perhaps a matching receiver :)
Is the whip antenna on the top and what size?
SI... VA BENE... MA NON C'È NIENTE IN TUTTO ,CARI BAMBINI DI 3 ANNI ,E NON PIÙ.
Parabéns!
Hello. I couldn't find an option with mesh holder and without liner, the one that you have. Can you share a link to the exact same Seahorse SE56 that you got?
Here you go www.amazon.com/Seahorse-Micro-Empty-Small-Black/dp/B07KXPR8P1/ref=mp_s_a_1_3?crid=10OIX7ND39R7Z&dib=eyJ2IjoiMSJ9.J9X18BqYHkq8h0nqcjjc7ubnJVDfSPD0rhHe1vTH1G6W9IbAjOTf8jB_8I9aZOJEAaZ7eMeix8wLm6KNJ3nuJBdmVl-uuInHy5JrFiR6yi4-2S7uqr-PIvG2zodT-FW6FuaMqpDH0GwKj6aoxhtyRw.LazqVRqlNBwqCXGX0C5fOEKp4BuQxHPR2urJqyYunjE&dib_tag=se&keywords=seahorse+se56&qid=1710868093&sprefix=seahorse+se56%2Caps%2C212&sr=8-3
Sorry, just saw that it did not have the mesh liner. You dont really need that, perhaps glue some foam in the lid
Really nice radio you've got and the QSO you've just has is just totally amazing and I think you said that your radio was made back in 1940 but that's very cool to have a good radio like that and it is also a piece of history as well which is very interesting stuff. Thanks and best 73's and you might catch me soon one day on the 40 meters and the 20 meters on phone OK cheers and best 73's for now cheers. Stephen M3SNV 73's.
Вы специально удалили мой комментарий и просьбу?
Excellent! thanks for the video. love making antennas!
Why is it so chirpy?
Bad 400v power supply regulation. Feeds the oscillator
Pw8gts muito bom parabéns
Nice! I like it!
Nice job, just printed, what size screws did you use to anchor the insert to the case?
Thanks. I do not remember :). Found some small screws in the junkbox that fit. Probably from some junked out computer or plastic kid toy.
Hi Tommy. Excellent video and a beautiful design on the power supply. I have just finished restoring a BC-455 and if you have a PC board available I'd be keen to build up one for my receiver. Thanks, 73 Paul VE7NRI
Fantastic radio 💯
Awesome
Thanks for the video! Do you have any contraptions for protecting the KX2 while operating by any chance? E.g. to protect from rain/snow.
Very nice and deferent work. I haven't the knowledge but i must beald one cupler.Can you help me with the automatic cycle?
How is it working out?
So far no issues, spent 3 winters in a unheated barn.
What connects to the center pole of the SO-239 connector?
The beginning of the coil
Thanks for the video. I printed it from thingiverse1 Heavier than i thought! Appreciate it.@@SA2CLC
How does the bottom hook up on the inside?
Make me one.. $$$