Видео

Donk

Your vid is spot on

Thanks that was a BIG HELP FOR ME...

Brother. It's May 30, 2024 and you got me feeling great. I did the entire operation on my 2017 GMC Sierra with some needle nose. This was the fix! You da man

Lifesaver

Yup just worked for me too. Mainly just hit them with a steel brush and gave them a little push. Then slightly moved it around when securing it back in and it worked.

Appreciate the video man. Made my life easier today.

Well it's been a year how many hydraulic pumps have you put on it. Because you know maxing out the pressure on the pumps going to blow seals. Should have saved yourself a big headache and a chunk of change by buying a Branson or a John Deere. Kubota is an overpriced piece of s***. Underpowered engine and underpowered hydraulics.

Thanks

They're hell to plug compared to a car tire. I found out the other day. I thought about using a drill but didn't have mine handy but I finally got it.

Thanks man. Replaced the fuel pump in my 2000 year Volvo fm420. It runs smoothly now. Watching your video made the job a lot easier! So thank you.

The fan supposed to move with the key on

Thanks!!! Sent this to my hubby and prayerfully it works for our Equinox!! Thanks again

I noticed the gauge you are using is trashed. The gauge should be at zero pressure with the tractor not running. 3K is high for a aluminium pump, don't be surprised when the pump takes a crap on you.

DUDE! It worked! Had the exact issue. Thank you!

I enjoyed your video, but I do have 1 question. Hoses have ratings, ie 3000psi, 5000psi etc. Do you know what your hoses are rated for considering you just upped your pressure past 3000psi?

Thanks, going to try that today

I also added shims to my L3010 from Jail Break and my Hydraulics are working great now. Little trick that i did to help with fluid loss, was to use a vacuum cleaner to suck at the vent hole and i didn't loose any Hydraulic fluid. Bob

Thank you buddy

It looks great. I'm going to do the same on my truck

If you have a 06 or 07 D12 your alternator mounts with four bolts through the case different from this video.

Thank you bro ! You save my time and money !!!

DON'T FEEL BAD BROTHER, I JUST DID THIS.

Can you tell me what wrong with my 1986 club car ds 36v golf cart. My cart will go in forward or reverse without the key turn on. When I put it in forward or reverse it will go. Thanks

I got a 1986 club car ds 36v and I need some very good pictures of the wiring og the charging port and the forward and reverse switch wiring and where they are hook up to. I see that your wiring that I see is what I need. Is there any way that you can send me some good pictures of your system. I appreciate that if you can. Thanks

Where can I get that kit

Thanks for this video and you save me tons of money for my 2017 gmc sierra!!!

Do you know what that part number is for solenoid by chance?

You sir are absolutely begging to bend your tilt cylinders...

Where is the fuel sensor for D12 volvo

Mine is the left side ...

did he run it

what is the part # for the kit with gauge??

I lent my tractor to a friend to use on his yard work, I tried running the tractor and drove it around in high revs and the engine started to bog down and lower rpms and then shake violently. It will do this a few times and then catch back up and the revs go back up. I am worried he filled it up with gas, the tank was pretty full so he might have only put a little gas in the diesel. My question, would gas in the diesel make it do this?

Use a press. Beating on them can bend the forks or throw the shaft out of balance

I totally agree. A loader ought to be able to lift a full load of dirt. PERIOD END OF DISCUSSION. You did it right, using a gauge. When iused to rent, id stack two washers in there, beat the crap out of it, then remove them and return it. Now i own one and will buy a gauge to fix it like you did. These aint deliicate machines. They are meant to WORK!

Great video

I would like to know what was the problem and how it worked after replacing the pressure pump

nice right arm what does the tractor look like?

Nice video, what you may run into is things bending like a grapple for example. Saw it happen when subjected to 3500 psi. Fortunately it wasnt mine so I was grateful for the cheap lesson. Checking your system pressure is a great idea.

Damn... if it were me I probably would've said $700 is my final offer and not push it further. Didn't know they were able to knock down prices that low...

How long have you been working the new pressure Any problems ?

I have a lot of Tekton tools most are top notch but a few are crap

Good vid

The manufacturer has tested this unit and set the hydraulic relief pressure to a level that will not damage the unit or the operator. Resetting the relief pressure is dangerous. You may blow hoses, damage cylinders or blow your hydraulic pump. Doing this will definitely void your warrantee.

A week ago I got a deal on a green 72" US General Series 2 rolling cabinet from my local Harbor Freight. They had put the Series 2 boxes on clearance about a month ago because the new Series 3 was coming out(now in stores May 2023). The one I got was the last one/display. It had a small scuff/not a dent on the side, and that was it. It was regularly $1,499, marked down to $1,299. The manager took off an additional 10 percent since it was the last one/display/minor blemish...and then I got approved for the Harbor Freight credit card that took off ANOTHER 10 percent with 12 months same as cash terms off everything I bought with it(socket organizers, pliers organizers, and a few other things). The Series 2 boxes are backwards compatible with the new Series 3 accessories, so I plan to buy the side cabinets and hutch when they get the green ones in stock. If you can find a 72" series 2 in stock at your local HF, they are now clearance priced at $1,169(because many are the display models).

Hey I am looking at a L4701 and can’t decide on the Industrial tire or Ag tire. What’s your experience with the industrial tire in wet slick muds. Thanks

Oh yeah, it worked like a charm on MY 2017 Tahoe! Thank you!

Thanks for spending the time to share this.

Thank you! Any idea which fuse is running that solenoid? My 2001 D12 fan is always engaged right now.