Видео

We have a 2010 and 2012 with the 2.0 turbo, both broke the balance chain tensioner guide. Its obvious the guide cannot take the stress of the tensioner putting pressure on that spot. If you get a loud metallic scraping noise and vibration, or sudden fast overheating, this is probably your problem.

I’m about to go do my daughters …what size bolts were those? I’m trying to get some tools together

I'll have to see if this works on my f150 so I don't have to open it with a rope anymore!😂😅

🤣😂😅 That hand though! 😂😅🤣 I'll try not to Hulk out on the next one 😘😂

How long did this last? Just wondering if i have a chance in hell to get by doin this.. just need for her to run until i can gather all the parts for the new engine to be put in.. but im pretty hopeless.. i know this probably wont fix my issue . Thanks for the video.

I recognize that exploded t-case scene...😂

Now I will drive the old gal!! 🤗🤗😍😍

Did you keep the stock tq convertor in the 4l80?

I got same issue but not fixing it im not getting any problems there help me got lost communications with parking assistant and lt gate care won't start and drains battery soooo fast help me please

i have a built 5.7LS that im building but im throwing a lq4 back in my truck for the time being and now i have full faith that the junkyard lq4 is going to be fine 🤣

I’d just cut the lines and pull from driver side. Don’t have to take the dash off. Slap some heater hose on and that’s it.

Every pin but one on my splice pack is giving me ground on my meter

This was the exact video I needed. I was asking my boyfriend to change it and he told me to look up how much went into it. I said I was sorry and never mind lol. Thank you for the time lapse

i have though about replacing my rod bearings and cam shafts and lifters and rocker arms on my 08 ford super duty 5.4l 3v, but i dont have issues with anything i just wanna replace em to replace em to give some life left to vehicle for another 200k miles it has 245k miles already, but doing an entire timing jon with brand new complete factory cylinder heads, head gaskets, studs, valve covers, exhaust manifolds, oil pan, rod bearings, timing chain set would be nice tbh... but even then cheaper to swap the engine with lower mileage one, or remanned one and rebuild or swap the transmission out and install a new truck bed and front fenders, hood, grille, get cab mounts, cross member supports, etc... redone and cab corners, rocker panels replaced

Would have been nice to meet you. Made it to the MST tent just as you were pulling off. Got to meet a few people from the group so that was pretty cool too. I tried to spot my white h3 out there somewhere in the video. Looks like you all had a great time. I know we did.

Kinda upset that I didn't go.. But also.. with paint and stuff.. being fresh.. It's probably best that I didn't.

Looks like icy chaos! Love it

What's up, man? I'm checking out your video now.

What a fun event!! I couldn't stop laughing with joy 🤘😆🥰

I was there yesterday also. I saw your channel on the back of your truck and had to subscribe

That’s what me that sunk the XJ😂😂. Whole motor was full of water and it froze just thawed and drained out 3 drain pans worth of mud

Work is amazing

I had this same problem I looked at this video 20 times went outside yesterday and fixed my wife’s truck in 5mins THANKS BRO YOU THE GOAT 💪🏽

I had no awd ended up being i think a green and white wire broken at the connector by the rear passenger side almost by tge bumper

Hmm... I wonder how much it would be to commission some real rocksliders for the gladiator.. (Frame-mount)

Turned out awesome! Can't wait to check it out in person at Winterfest. Now I have to brave the dark, cold, and snow to get the F-Zomb50 ready!

Badass Bumper!

Nice little ram-rod for the pretty girl 😍🙌

My 2007 ford expedition. Has small emissions leak and looking at this its could easily be my car problem

After over $600 on my 2012 GMC they figured out that my truck stereo was bad and that’s why my truck wouldn’t start. So I guess gm thinks it’s fine to be stranded because of my stereo. 😒

If they come with junk engine it is a junk CAR !!!!

Fingers crossed, nice video 👍

Can anyone please walk me through how to get to the motor blower on a 2013 Chevy cruz.. i have been watching youtube videos to figure it out, but im a dumb blonde. I got the glove box off but i just can't figure out how to take i believe the airbag to get to the motor blower ughh

We just watched this at the mst clubhouse. What’s riot! Truck makes everything look easy

Sorry that footage was so all over... Drone did not like the branches and stuff. Lol.

I was the toyota fj in a couple parts of the video, it's crazy how you walked that obstacle at 19:50 I got sucked into the rut and it looks so much worse for me then you haha 😅😅😅

What an awesome event! So much fun! 🤙❤️

Dang, looked like so much fun! Hopefully they do again next year so I can give it a go! That one hill climb, though.... if the Tahoe had a bit of trouble, I'm not sure the F-Zomb50 would've made it. I would've given it the beans trying, though!!!

Well done ! Thanks ! Just subscribed.

Can one use a 2 or 3 jaw puller to remove the hub? I don't have the hub puller whacker that you used.

That's sweet except you didn't show how or what you did.. I'm currently doing the same thing.. and wad trying to verify some marks to confirm mine is out of time . Looking to put It neck in

I've got a 2011 Silverado with a no crank no start issue. Used a scan tool to check for codes and its showing P0690.

Hey MR Busted. I got 2017 4.3l AFM here. I did the parts cannon thing first and replaced all the injectors, wires, and plugs. Still have misfire (ONLY AT IDLE) on number 4, same as what you got in this video. No excessive rocker arm play, performed cylinder leakage test (passed), but compression seems low at 95-100psi across all cylinders. Im grasping at straws at this point, any thoughts?! I'm a chrysler tech and have very little exp with these motors. Any help would be appreciated.

He called the shit poop!!!

Gd video and helpful thanks

Holy 💩!!! Kinda afraid to pop my diff cover...😬

Where's the fuel injectors located 🙏

Would you happen to know where the fuel injectors are located🙏

Did you happen to have the PCM Relay keep clicking while the power was on? I have all the same lights going off and on and the PCM is click consciously, any advise would help. Great video by the way.

J'actionne le defroste avant au maximum , pas d'air mais l'air sort partout ailleur à la place très bien ce n'est pas normal