Видео

I would not know where to go back 🙂

How can I obtain the blueprints for the Titan Super Talon vertical take-off kit?

i am using heewing f405 f cont.ardupilot thanks

hi could u please send a pram .i am using tx16 ex press lrs dji 03 i can only get dji bat volts in my goggles 2 please help

Oh,, thank you very much! I build the same project. Its so hard after quad. If you have another recommendations i will listen to you with pleasure.

😮Which flight controller are you using?

Ardu or iNav ?

Nice

really nice build Andreas. Would you pease share the stl 3d print files for the vtol parts. That would be amazing and much appreciated !

When your plane is a helicopter you don't need to ride the bus.

Great video, What flight board are you running ? Is it the stock board or did you upgrade.

Amazing, well done!!!

Great😊 are you using inav ?

what filament was used here?

Can this T2 vtol, using 6s2p21700 liion?

Hello! Where can I get models of this modification?

What is the power setup? Motors, props, batteries?

Bravo.thenks go Ahead

Superb !!!

А какие у тебя получились значения PID ? У меня родной vtol комплект и со стандартными значениями pid регулятора его очень сильно трясёт, даже взлететь не получается (Я знаю копировать чужие pid настройки не стоит Но мне бы хотя бы понять от чего отталкиваться)

hi what is your vtol setup?

Hola buenas tardes, donde se puede comprar, gracias

Nice review, thanks. How long it will be in the air and how many km will fly with one battery? Thank you.

τι ND φορας?

hi nice video so is possible automatic landing rth with inav with this vtol ? thanks for reply 😊

Inav7 ??

Hello, what specific motors and propellers did you use?

Outstanding!

Next improvement...use also tail motor for forward propulsion...

Love that shot from the drone pov- it was there then It wasnt. Nice!

take you PID to half and then do a quad tune, and later a plane tune and will flight like a dream.

oh damn... uhuporr on the left wing😢🙈

Hi did i saw standoff mount for hold tilt mechanism?

Just a suggestion, I think you need to extend your wing motors farther forward towards the front of the aircraft. I believe this is why your transition to forward flight is not smooth.

where is the cg point，I set mine at the original position but when I switch it to fix wing model, it will pitch up to vertical. can't control it

Πολυ ωραιο.Το πηρες απο εδω η ηταν παραγγελια απο εξωτερικο.Σ ευχαριστω

Καλή χρονιά και χρόνια πολλά. Με ενδιαφέρει το συγκεκριμένο project. Σκέπτεστε να το διαθέτετε προς πώληση σε μορφή ready to fly;;;

Υπέροχο εργαλείο.Απο που το πήρες?

Hii can u share stl file for mount vtol

not stable on tricopter mode. INAV is never closed to ardupilot on VTOL thing,

I need this in BNF. I’m to old and dumb to set up boards.

nice, my version ruclips.net/video/BVvvgoWDL7M/видео.html

Hello Which one do you prefer t2 or swordfish? Is it possible to give me some suggestions I had DJI integra goggle and o3 air unit and Rc controller 2. Is it possible to use them on t2 or swordfish? If you buy a new radio elrs one which will be your choice?

Hi do you mind share the stl file for this setup pls

*Promo sm* 🙃

Amazing Work

great, you don't loose any authority on pitch/rudder due to the 3rd motor on the wind flux in front of the Vstab ?

great job, can you share more detailed information about the plane?

Uπομονη ερχεται και το CRUZA T2 VTOL

Andreas,Omg! that is professional ,have a nice day~:))