Видео

What is the symptoms or what does the noise sound like of bad rear axle wheel bearings? I’m hearing a rotational squeaking noise at the rear of my truck and I’m thinking it’s wheel bearings but not sure, I uploaded a video on my channel if that helps.

Nissan Part Number for Engine coolant pipe o-ring : 21049-3z010

Currently having the same problem 😢

Yep. me too. threw parts at it until I found this video, and now its fixed. Had a small crack in the bottle. Thanks!!!

Did you have the jack the care at any time? Coz you had to go under at some point

I just replaced a blown head gasket and it is overheating. What do you think?

Also check the throttle body coolant in and outlet and hose . Those can clog up and reduce the efficiency of flow

What is the average cost of this?

i had the same problem and did every thing else like you did and then change reservoir and its fixed so thank you for that ..............cruze is junk

Had the same problem once before on my 2019 Chevy Trax, same exact 1.4L Ecotec engine. Water pump gave out on me at 52K miles (free replacement under warranty). I've gotten the water pump replaced after that.

Super Thanks for your good explanation

Thermostat 18 bucks on eBay takes 25 minutes

Did you drain the coolant first ?

V6 or 4 cylinder?

Brilliant way to get that hub off, thanks for the tip!!!

I watched many videos as I have an issue on my 2012 odyssey mounts. This video added a lot of info and made it seem easy to do. For the front mount, removing the battery tray and accessing the front mount from that angle looks great. I have more confidence now to tackle my mounts. Thank u so much.

Your head is already warped when the engine warms up the heat pulls the center of the head up just enough to let the compression into the cooling system.

I had bubbling in the reservoir. I changed the thermostat and a heat sensor. But it kept doing it. I had air int je system. I had to empty the radiator from the bottom. I bought a new reservoir . Before putting new coolant in. There is a white screw / plug on the radiator topright passenger side unscrew that add coolant slowly. When coolant comes out the hole. Plug up hole and turn on car keep an eye on the reservoir add slowly until filled between min and max.

Nice video

This video just saved me $375 from ordering a new amp from Honda. Never soldered before but I got it and it works great. Thank you for sharing!!!

I just had this nightmare. I fixed the thermostat and got air in my system. I had to flush the radiator and on passenger side top of radiator there is a plug/ screw open that. Add coolant slowly until coolant leaks thru radiator screw back plug. Turn on car and watch level. I also got a new reservoir. And it's good to go

Thanks for the video

Do you have a part number for that o ring?

Im experiencing the same exact problem i have a 2014 1.4 cruze doing the same thing problem came out of nowhere.. what was the problem

I appreciate ur thoroughness had a guy who did my mounts and took off my fan assembly and couple screws were rusted on bottom so he just left it dangling so th fan has been shaking,I jacked it up and put couple screws in 2 arms attached to fan and bottom tray of radiator I shimed them alil and drilled fo screws and shaking has stopped like th idea of removing battery tray thsnk you emano

😓 *promo sm*

Honestly one of the most helpful videos I’ve seen on this. Thank you very much! Keep the videos coming! 😊

You literally just saved me from the exact same issue. I already burned out 2 starters sadly until I also realized I had the wires hooked incorrectly on my starter relay similar to your video thank you for the awesome save!!! 🎉

Hey man, you have an instagram?

My Cruze's coolant boiled and gushed out of the kettle. The repair shop said it needed an engine replacement. I was thinking of crashing it into a tree, but after seeing this video, I'm willing to give it a try.

I have same problem I replaced the vitec the same code still here

Could be the cause for injector failure the loose sparkplug.

We just bought a 2013 Chevy Cruze with the same engine and it started overheating the day we got it and we replaced the thermostat housing and then it started smoking out the engine and found out it has a blown head gasket. $4,000 down the drain because we can't find a mechanic within a hundred miles that will do head gaskets anymore

If you tore it down so far you should’ve just went ahead and changed the water pump while you’re at it.

Something is making the tire wear unevenly. I had a bad shock.

Nice video. From my experience in replacing alternators with a aftermarket reman sometimes you get lucky and they last. Sometimes you don't and they fail few months later. For Toyota owners I rec denso aftermarket remanufactured alternator and starters. When I was a sales guy in parts for kraken I would tell them lifetime alternators. Never pay for a alternator again. But didn't tell them how many times they would have to take it out if it fails. Lol

Fully agree, had a honda I was convinced it had a noisy bearing, turned out to be carcase damaged/torn inside the rubber. Also look from behind when spinning, sometimes damage is side to side distottion

Easiest way is to take the wheel off, and then drive about 50 ft. You will hear

a road on the edge hahahaha

a pipe hahaha

its not called slide hammer ....in English is slap hammer hahahaha

How to destroy your valve cover in 3, 2, 1....

The van will be back for a new water pump very soon lol

Good

That upper ball joint ain’t looking great either

Buddy might as well just tell us to drill a hole through the cover lol come on

Use a seal puller

That's not a bolt my dude, its a screw.

THERE WAS DAMAGE