Видео

Do you still offer batteries repair service? thanks

I found an accidental trick to make them charge again, I connected wrong the multi to it and put them back to the charger and it did now works normal

Hi can you reprogram help me for this battery please, address please

Great video, but my torque driver isn't narrow enough to fit down to the 1.5mm screws under the cover at the rear. How narrow is it so I can try and buy the right sized driver

How can I get in contact with you. And are you still repairing phantom four pro batteries. I have. One that is doing exactly what this one in the video is doing.

Great video. Saved my drone. Thank you!!

do you still service?

Good day. Are you still repairing Phantom 4 Pro batteries? I have two that need repaired and reprogrammed.

Just watched this tutorial and now have a working drone! Thank you kind sir!

I have two Phantom 4 batteries that need to reset, do you still do them? Sent e-mail to you but properly went to your junk mail.

why are you not using the reset button on the battery? just jumper the reset button and the battery minus.

Thanks for this video! I had a broken rear arm rotating axis part. Ordered new one from Ebay and I was able to replace it by myself because of this video 👍👍👍 Thanks once again 🙌

Fantastic explanation - but the music isn't necessary and so repetitive! Thanks again.

thanks for your educate vedio - what is module of programmer , used here

hi can you fix my drone battery ?

I guess I need to buy a new battery

Thanks for the video. My drone has a problem with the horizon. As the altitude increases, the horizon becomes slanted. I have a video of it here 6gTjPYdv9RM What is the reason for this, what is the cause?

Do you still offer this service? Do you work on phantom 3 batteries?

how can i sip my battery to you from Nigeria

Hello sir ,where we can get that module box ?

Hi my gimble is straight at startup than goes to left and gets a gimbal motor error, do you think it’s a bad cable? 27:29

What program do you use to calibrate on the computer?

Hello, does the MSP430 controller (EV2400 mini) work?

What do you do if very first 2 screws rusty and thread is gone any other techniques we can apply ?

Really helped me! great tutorial! thanks :)

Fook that, am gonna stick a nail through both of mine LOL

What is the glue you used ?

maraming salamat po!!! MABUHAY!!!

Hi. Fantastic video. Thanks to you I was able to repair my drone that had a broken arm axel. Instead of a big bill it cost me % euros for the part!!! Thanks so much. Good job

Hello i have two phantom 3 batteries never use not even first charge any way you can save them

Can I use st link or cjmcu 2112 adapter

How can I charge dead battery without taking it apart also what pins can I check the voltage on from the back of the battery

I have a problem with my Mavic 2 Zoom, some jitter on yaw axis appear from time to time(no error message for the motor though). You say something about some bad batch of yaw motors... Could this be the cause în my case? I bought the drone S-H, the seller swored it did not crash it, there were no signs but I couldn't see the problem with the yaw motor then but when it was too late to return it. The gimbal is mechanically fine, end points are ok, no springiness, no bendings...I now have to decide between buying a complete gimbal or just the yaw motor. Any idea, please?

Quiero la Información donde mandar mi batería te hi el mismo problema

Hello, I really enjoyed the video and your explanation! I wanted to ask if you happen to know what the white glue that DJI uses is? (On the wires of the drone so they don't move and also in the battery you can see it above) Thanks

Its better to Buy a nrw one.

Where can I find these parts? Like a replacement yaw motor?

Do you still service Phantom 4 batteries?

My motor is seized it wasn’t spinning when I got it out of the bag, it won’t rotate freely but is receiving power. Also all of the lights are the exact same as yours.

Hello thanks for your video I am trying to balance a DJI Phantom 4 Dron smart battery. After watching your video got a Venom PRODUO charger. After opening the battery I found out that the conector or balancing lead of the battery to the BMS Board is a 5 pin JST SH 1.0mm and the 5 pin female conector of the Venom charger adaptor is a JST XH 2.5 mm. I am ready to make a custom conector male JST XH 2.5 mm to a female JST SH 1.0 mm, my only concern is the order of the cables. Can you help please? I just want to know wich pin in the 5 pin female JST XH Adaptor is the ground as I have 5 cables in my battery balancing lead, 4 reds and one black. Thanks for your help

Solid video bubba …. Completely appreciate it… helped replace my rear arm … cheers mate

Hi how I send my batteries to you for repair? Also, how much do you charge per battery? Thanks.

Great, but you didn't show the lipo balance settings... Could you please confirm your settings. Thank you

2-3 amps. how many volts? does it matter?

Hello brother, can you give me a address to repair battery drone 4 please, thanks

Sent you a msg on your website, p4p white battery with this issue here as well.

great tutorial, unfortunately my soldering skills aren't as great though and I screwed it up!

So how to calibrate the drone?

Great video! Replaced my cable and all works well. Thanks!!!

Thank you sir