- Видео 12
- Просмотров 27 237
scooter boy30
Добавлен 18 дек 2015
Видео
cheap quality Honda ruckus gy6 swap harness
Просмотров 1282 года назад
cheap quality Honda ruckus gy6 swap harness
Are AliExpress ruckus gy6 mounts any good?
Просмотров 3292 года назад
Are AliExpress ruckus gy6 mounts any good?
150cc gy6 reverse gear fix.the easy way.
Просмотров 19 тыс.3 года назад
150cc gy6 reverse gear fix.the easy way.
ruckus clone frame grinding.
Просмотров 843 года назад
trimming the frame of it's 50cc components . getting ready for the 150cc swap.
I have that re-occurring problem even with my 2009 Honda Element - both sides.
Thanks!
Was this gy6 and is a 12” stretch mount
Nevermind i rewatched video but do have video or pics after install
There's literally an adjuster right behind where you showed putting in your spacer.
That was kick ass!
This will definitely help! Bout to start sound deadening 😊
👍
Thank you for the video! Just did this after I kept hearing water sloshing around in my engine area! Took the cover off, as suggested in this clip, and the whole of the channel/well was filled with rain water! Thank you again!
Will try this when I get off work you think this will help my driver side floor?
You dont know how much you save me some grey hair from stress 😅..these things brand new give problems
Is it the same fix for going forward? I pop out a gear going forward.
Would this cause the driverside floor to get wet? TIA
Did you find out?
You know it has an adjustment right?
fing yeah dude thanks
No problem buddy.just trying to help
Nice. I am chasing a wet floor mat on the driver's side, I'm going to check mine out. Thanks for posting.
Your welcome
Did it work?
@@FutureDreamZz I think that my wet floor mat, on the drivers side, was due to the 2005 Honda Civic being wrecked. The drivers side fender was pushed back and may have cracked a spot weld. I sprayed undercoat as far back as I could into the recess and also used a silicon sealer around the windshield gasket. Also, I sealed the windshield gasket because the technician who replaced the windshield told me that there was rust at the upper right hand corner (looking from the front of the car) of the windshield. Most of the time the Civic stays in the garage.
Did this stop the leak? Or did you have to take the fender liner off and clean where the drain goes?
That stopped the leak.i had a stick clogging one of the flaps and it was causing the water to overflow.i cleaned the flaps ran a pressure washer inside the fender drain and it never did it again.i also put a fresh vent cowl gasket on as well.
That's not a fix bud...
My 150cc 4stroke GY6 goes in reverse but not forward
I'm in the same boat, mine goes in forward but as you run it, it wants to jump randomly like it misses a tooth
@@joshuagoodnite1808 did you get it fixed? Mine stopped going in reverse. Just have forward whether in neutral and reverse....still only goes forward.
Will that work for a 13x8 wheel too?
Yes
Why not adjust the cable?
I did adjust the cable first.but it was a cheap Chinese reverse gear box and it wasn't going in gears smoothly.so I needed to shim the front cable hole to fix whatever was incorrect or inconsistent in the gearbox
I saw your comment on Cory's video do some research before talking
Sweet that's a huge load off, i just ordered one of these about a month ago and i'm still waiting for it. It honestly looks to me like theres at least 1 "big name" reseller just lasering their logos on these and reselling them. BWSP sells the ali ones, on ali, for a 150 dollar markup.
I only buy my offshore stuff from him.hes a good dude with great prices.
This might have been my problem all along 🤦🏻♂️ thanks bro.
No problem man.
What kinda kart do havs
from where i purchase it
I used a small 1/4 piece of spacer the size of the inside of the shaft.it fit perfectly and kept enough tension on the spring to move the reverse gear.
what is the point of the bracket on the clutch having that link in it on the motor flange? the bolt and link rattled loose out of mine and I think I'm just going to fab up my own piece since it's basically hard mounted.
Would you be able to show the 1/4 inch dial yiu are talking about ?