Видео

Mesures

useless

I like your ethical good use of tools ie ratchet hammer

We’re is the plans to build them so we can make them

Hey man I have been where you are before. Don't let these bums make you feel less than. You are doing your best with what you have and learning along the way. This video was helpful to me, keep up the good work.

try loosening the lugs while the car is on the ground first then jack it up. tire changing 101

VW centercaps on a RAM?

That’s absolutely brilliant! Been looking for ages for a video which doesn’t state the obvious (eg broken rod…). Can’t wait to do mine when I get home. All six throughout the house have gone!!

Fox blinds? 😆 Are we talking about faux wood blinds? It's French, pronounced like "foh" with a long O. Good video, thanks.

💀💀💀

Polisi bela kesesatan sedangkan FPI g dibela

Kids when they realize screaming “dick” and “pussy” is not funny: 🤯😡😡

Sorry for a the people that make fun of you and the video. It was helpful for me. Now after I know how to get to the bolts I can screw them tight :)

use a dremmel to shorten the thread so you can get the spanner on

Similar problem...only the blinds turned partially one way but not the other...only then pulling the top blind up against the rail ...took it down and everything seemed ok compared to an identical blind that works...the string inside the wheel was at a minimum...likely causing the lack of movement...so I tried rolling some string back...but the problem still exists.

These haters can't even say how they would have done it better. Lol

Angel , rhythm,bass,make that wield layer it in place..

Might should have started on a flat surface and got you heat right. Good luck homie!

Tacs are prob best for that though...so you don't starship enterprise everything. Aka warp

Nah, ya see, the problem is that the pokey bit isn't pokin' around as much as it should. Ya gotta poke it more

Gotta start somewhere bro...get a puddle going n go

Lil baby chainsaw 🤣

Waiting for Sandals here to lose a toe.

Oh my god the amount of cringe in this video is painful. This person should lot be allowed to operate a lawn mower let alone a chainsaw.

Will you sell them?

Now is still the 2nd best time to delete this.

Very nice video

Poor guy. Good try. You guys in the comments are just cruel.

This stuff is amazing!!! Thank you Maggie's farm. Those other brand traps dont work so well. See ants (even carpenter ants) put out this goop, they disappear like magic. ⭐⭐⭐⭐⭐

Wow

Medidas

How would you fix a round newel post? It doesn't show that type of attaching system?

Great repair job..thanks for sharing!!

A professional Novice, 6 minute video, to show the world that he still has a wonky stair rail 😂

Thanks man, I needed that!!!

For the covers just buy a piece of oak and cut it the same diameter, stain it before, a small smear of Titebond 3 around the outside and use a rubber mallet to hammer it into place. Easy and better looking. But I guess if it comes loose all the time easier access might be worth it.

This is the funniest construction video I’ve ever seen. Never thought I’d see a man hammering a screw with a socket wrench to tighten a nut. Was looking for another video but stuck around because of the comedy. Good job.

Interest video. I built my stair rails years ago and they’re loosing up. I didn’t know how to access the bolts. Didn’t think about drilling the caps out. My caps are underneath and are oat so it’s tough to drill. One little tip that might help you a little bit. The screw that was too long, you could get a small hack saw and cut it down so the wrench will fit over it. Also when i built my rails, Home Depot had these brackets that screws into the post and floor and made it super staple. It came with a wood trim to hide the brackets.

Next project change your smoke detector batteries and stop the chirp.... Important to use the wrench to beat the battery door closed 🤣

LOL!!! Ratchet as a hammer, Allen Key as a wrench.. and 25 spanners ! This video is actual comedy genius! Thank you!

Using the rachet as a hammer? Should of left the drywall screws in.