Видео

But you may lose video connection while steel having elrs. Or you may configure souns warning on rc according to telemetry

Yes, it is possible. Disconnect that small bridges and connect crsf to any of serials. But up to me there is no sence. If you need crossfire - then it makes sense to take 4-in-1 as it is the same but without elrs

@petrokey_en I purchased the air 65 drone with 4 in 1 fc to put a tbs rx on it. But the seller sent it with 5 in 1 fc.

@cesargurc911 ah, got it. Well you need disconnect bridges and may connect tbs. Is it a limited one?

Thanks!

Well, as I noticed the puds differs. Do not know 100% but suppose they config for air65.. but again - not sure The difference - in accuracy of control

Хмм.. не видел такого в описании.. попробую узнать

Have never worked with ardupilot so no much help from me.. but at least few assumptions. Bandit should be the same half duplex devices as all other so should work similar. The question if it is connected directly to pc or via radio? And may check serial baudrate - newer versions of elrs that supports 1000packet rate also may require higher serial speed

Yes. And also it is possible to programm different levels of vtx power. Joshua Bardwell has a good video howto

Theoretically it can cover about 80km (in ideal conditions without obsticles in clear air high enough). But it depends too much on antenna, receiver and many other factors

Unfortunately not. It uses proprietary flight controller that does not work with betaflight . Instead - may use betafpv configurator - it looks very similar but less options available

Well, up to me the size and formfactor is the first cryteria for decision. Just what size and form more comfortable

Corrected intro. Added short list of questions I cover just at first seconds so anyone can understand what the video about

Well, yes. And after video published I have also destroyed a contact - but I have destroyed a usb plug

​@@petrokey_en but honestly. After a week of intensive abuse of this quad, it is pretty much indestructible. Only problem is that cam plug, sometimes it came loose after big hit

Yes, you can

It is analog video system at 5.8GHz

@@petrokey_en thank you!

Well, question ti Betafpv.. but actually it will have more weight and more power consumption. Needs check if it will remain same smart

I know 3) English, russian, ukrainian. And learning romanian)

@@petrokey_en Great, one more channel to go... Have you seen meteor 75 air yet?

@user-rt9pe8dp1q ah, epidemic sound allows only 3 channel at a time)) will need another license)) I have not seen air75 yet. It has abit bigger engines and bigger frame that fits bigger battaries (same as meteor75 or cetus). But fc is the same

​@@petrokey_en air canopy is rather interesting. Allows to change camera angle by unscrewing one screw...

Well, I've got a comment that I've used wrong battary. The 21700 should be used - as I understood it should fit well.... Or I should go to doctor to treat flu))

Словами классиков... кроликов - "очень э тэйбл!"

Yeah! idkfa should let me break through the closed dor with my drone)))

Well, Cetus has few week itrms that may fail with time. - the motors wires are connected with connector but not soldered. The connection gets oxigen cover with the time and connectors overheats and motors start work not so good. But it is possible to replace connectors or simpli solder the wires And camera sandwich overheat. Well, configs like minimal power till first arm helps. And may install radiator. However I would look at new pavo or at least meteor series that have better ventilation (however still have simple motir wires connectors)

Oh okay, I have a bunch of those laying around from toy quad vtxes anyway and I'll probably use pit mode or something and will probably run my vtx at 200 mw unless i really go do some range. Does the female connectors for motors on the quad oxidise too or is it only the motor connected bits?

@adakalyoncu1913 well, both sides of contact oxides, but from my practice change of connector at the motor wire usually helps. As for power if fly at home the or outside within 50m range - 25mw should be enough

@@petrokey_en hey I have another question, I did get the cetus x and I keep getting this core temperature 70 celcius warning, it doesn’t go above like 73 most of the time and sometimes goes away sometimes comes back. It didn’t happen in my tinyhawk but it apparently does with cetus. Should I do anything about it for the aio to not get damaged over time or will it handle some heat just fine without like me having to buy a new aio every few months? I’ve heard terrible things from other people about how the quad is expensive to maintain and stuff goes wrong but the same people also always crash the drone and stuff and you say you’ve kept it running for a year so I wanna hear if you experienced any issues

@adakalyoncu1913 up to 80 degree should be ok. Yes, cetus heats more then others because of closed frame that does not allow it ventilate good. So I let it cool down a bit after flight at sunny days

Yes, as I understood the osd is applied at vtx, so the 3th wire sends vtx controll info (like power and frequency) and osd data

That's a problem. I do not know a driver fix. Only - update firmware of rc to stable one (same as with aquila kit). But I do not have direct link to literadio3 stable sw - needs ask at betafpv support team. And the cetus x should be also downgraded to sw betaflight 4.3.1 (as it uses elrs2 compatible with stable rc sw)

Yeah.. I'm not surprised...

Yes. It has connector so no soldering

So auto search channel does not work? (Aquila might change channel by D switch toggle) If not - can you try disassemble and check if wire still connected to vtx, and if antenna (a small piece of wire) not broken?

​@@petrokey_en no it connects to the drone the goggles connect to the drone and also i checked the antena its still connected also the fpv module is blinking blue light like not the drone only the camera part but the goggles just show a black screen with numbers above it like the signal that its on do you know i could contact beta fpv if it ends up not working do you think i could buy the co4 with vtx think and attach it to the drone or what should i do

@prohackerahmedzagabra5874 the numbers you are speaking about - is it a drine info like battary value or mode? If you have these OSD then the vtx itself is ok, but problem with camera. I am not sure about c04. I know that betaflight version (with 5 wires) will not work because of different proptiatory digital protocol used. But about c04 Cetus - needs clarify with Betafpv support

@@petrokey_en its not the osd its something else do you know how i could contact beta fpv support the thing that shows in the screen is the signal that its connected to

I've sent this question to betafpv. Waiting for responce (they have holidays). Anyway mail or 'ticket' form is available here support.betafpv.com/hc/en-us/articles/900004682543-Contact-US#:~:text=Please%20don't%20hesitate%20to,Email%3A%20support%40betafpv.com

Aquila does not work with betaflight sw. You will need 'betafpv configurator' sw (it looks similar but it is another one

@@petrokey_en bettt bro thxs a lot

Yes. If you've bought cetus x long time ago then most likely you have elrs2. Then will need downgrade elrs version of aquila to 2 (see next video)

Thanks!!

Thanks! Adding runcam thumb is not too hard, but I am not sure if Aquila is powerful enough to carry one. For Cetus it was difficult in some cases and Aquila is definitely less powerful

The wifi antenna at drone is week, so needs move closer to PC. Or even turn off home wifi router And the remote should be turned off (itherwares drine will connect to rc and do not swich to wifi mode)