Видео

@@FEboats that's what I plan on doing my self keep one on the shelf which is the Vegas version Monday my local shops ordering another in for me lol sold a xmaxx so I'm thinking of doing a straight 4s or stuffing a xlx2 and tp power motor in one see if I can keep it planted on 8s

That props more in the 34mm range I've cut it way down but I have a question have you noticed excessive wear on the bushings of your strut I mean I clean and re grease every run and I've never had a boat get as much strut wobble as this little thing has gotten it's not just this one I've also got the heat wave version and its strut has got some pretty good play as well and it's still on the stock prop I'll do a vid to show

@@600bubba yeah mines ruined after a dozen packs. Planning to contact horizon but that isn’t easy anymore.

No that bike was pulled from the lake about a hour prior most likely stolen

However I have stuffed 2 26 inch recoil2 in a military backpack and strapped the sonic wake to my sv650 before lol

Right i probably ran 4 sets of batteries through it was most planted with my gens ace basher 8000 mah 3s packs but there heavy asf

@@600bubba yeah those are heavy. I have some 9500 and 10,000’s they don’t fit without the battery trays.

​​@@FEboatsi decased my basher packs awhile back and wrapped them in 1mm thick heat shrink they barely fit lol ran for 15+ mins doing pulls never once got hot

Thanks brother figured out why the black jack 24 popped the ztw ESC lol didn't pay close enough attention maybe a few too many dabs but I put the post in the negative slot on the connector when I soldered it up lol 29 buck ESC so now it gets a fly color 150 as well

Running late but just made it out to the lake with 4 boats

It's quick lol barely bliping full trigger at times wants to come off the water

Thanks brother wasn't worried about the tire had built up that billet case minarelli 70 and that day I drove about 4 hours for a group ride and it no matter what jetting I ran was left and right cold seizing then about 5 mins later un seizing so I said f it and was trying to kill it got home honed the cylinder slapped a new piston and ring in it and still ran great last summer

That bike was built with 29s as it would raise the exhaust tip off the ground higher just threw the 26s on for a first start lol couldn't lean right with them as the pipe was only a inch off the ground with them 29s now with maxxis hookworms

None a spool/ locker I made on my cnc machine

Car is a shelf queen now it's hit it target of 105.3 mph

Этот мотор форсированный своими руками такой не купиш только сам если доводить штатный мотор до ума

Unfortunately I'm back home brother I will be back out at the pond tomorrow morning sometime

@fly1moto okay ill try and make it there

@@anarochrc986 ill be out around 12 to 1

@@anarochrc986 apologies brother we had a fire here at the house so I'm heading down here in the next half hour

@@600bubba okay you still there?

Cafe light re wired and new leds of my choice I'll do a vid on it soon can't link because it's too many links to build

Thank you brother I'll get the vid done tonight of the mini e Revo spur install

Bone stock car brother 2s in that vid its now got a 4s castle system with a tp power 2030 motor running 45 pinion 58 spur

Do you think maybe we could raise the motor. Or perhaps and angled skid chassis?

I've built 3 all with revolvers not had any drive line fitment issues with them have about 1.5 mm clearance on the front shafts from the motor can

@@600bubba how’d you manage to fit them. I’ve seen others and they can’t get the front driveshaft on with the 280.

It's best to just get metal shafts like the injora ones as that is a issue Ive had the motor has enough to snap the plastic ones like a toothpick

@@600bubba but did you have to modify anything besides the spur mount on the revolver.

Nope bolts right in just a drop of proline tire glue holds the pinion on the motor and your good to go have 20+hours on this rig now and it's holding strong the drive shafts are the only thing I've broke

@@600bubba is it 4wd still or just rwd?

This is a 50mm iron sleeved case reed sleeve is from l.a sleeves piston is a ms440 50mm 10mm pin piston saw style ports in the sleeve jake head had to be clearanced to accommodate the 1.5 mm of pertuding piston 40mm stroke