Видео

This is such a cool project! Thank you so much for sharing this with us. May I ask, is it possible to connect the pizoelectric sensors in matrix? So you can basically create a more precise (heat) mapping in the app to see even more accurate weight distribution? Looking forward to your answer!

I bought the 4 relay version but cannot find instructions for its programming. I did not work by default it seems.

Hi! I have a question, will it work if we map the readings of both sensors first? Because when I try to mapping both sensor readings, the serial monitor shows the same result on both sensors. even though the knob on the potentio (sensor) is in a different position. I have no clue to solve this problem, do you have the solution? Thankyou! Nice vid btw!

can you run a 24v motor with this from a 12v battery? thanks

So lame, it needs you to make an account with some corporation that then tries to sell you stuff and limits what you can do with your Arduino. This isn't a tutorial it's an ad.

Nice , just need a small help , can i do this woth arduino nano?

How can I power 6v solenoid?

This circuit can destruct the Arduino when the wiper of the pot reaches the ground. Possible short-circuit!

Thank you! I installed a small tactile button. I pressed the button, while plugging into the computer, then BOOM! It's alive!

The blynk app is it still working still for the pressure insole template?

Hello, can you please give a new qr code for the blynk template? The old one does not working anymore.

Hallo, der QR Code zum hinzufügen in der Blynk App funktioniert nicht mehr. Könnten Sie bitte einen neuen bereitstellen?

Can you please name the components used in this project?

Excuse me, I get an error in the serial monitor, it says that the ESP-01 is not responding, but I followed all the instructions correctly

Great explanation would this work for a diesel heater 12v

Thank you so much. I was not sure about the wiring and I thought I need extra power to run the relay. But after watching your video, I have known that its so easy. Thank you from Bangladesh.

Great video, love a wiring diagram. Heres my question though, are the modules encoded with their own keys, or are they just listening for ANY signal on the 433 MHz channel?

Bhai tune last moment pe Jann bachaiyeer thanks bhaii ❤

you gained a sub man true and brilliant work great help i just got my first esp32 this helped me no actually made me able to setup blynk on it

Very helpful, thank you!

Well shown visually, and explained very well... Too ... Thanks... Thom in Scotland.

Can ESP32S work according to this ?

Can Alexa be used to transmit to a hidden spy camera or listening device? Can the device be powered by alexa?

very good. How to measure current with ACS712?

on NodeMCU when I use the pin GPIO13 or D7 it works fine but if I change the pin the data I get is not correct any fix???

Hi Dear Friend. Great Project! What's de RPM of motor ? In this project what's rotation you chose for this motor ?

Hi Dear Friend. Great Project! What's de RPM of motor ? In this project what's rotation you chose for this motor ?

Hi Dear Friend. Great Project! What's de RPM of motor ? In this project what's rotation you choose for this motor

You have problem with this video. You cannot hear the comentary just a load of music so no explanation!!!

Would this work with a 12v solenoid valve, also if I were to connect a button to the battery and solenoid valve, and then connect the grounds from the battery to the valve, would it still open if I pressed the button, and then close if I press again?

Pretty cool. Could you go overt the parts list of what is needed for this...Please

hi, sorry but why my AT says failed to connect to Wifi ?

Wow, what a nice video.

Very nice. Will 12V to 5V 5A powermodule DC-DC step-down power supply converter can power the usb port to usb port?

D6 in the drawing should be D3 shouldn´t it ? D6 got no pullup resistor afaik.

Is this waterproof, doesn't seem so where the plugs are

How would I make the solenoid activate and deactivate continuously as long as the button is pressed?

Thank you so much! This is what I was looking for!

Old clip, but good point on the programmer. I spent the best part of a day with an Arduino and 2 x FTDI programmers fighting unreliable uploads. Worked fine for sketches but the firmware would crash anywhere between 1% and 99%. Modded the plug in ESP-01 programmer you used with a reset and programming switch and firmware upload works every time now. Still can't get AT commands to work from Arduino IDE serial monitor.... but one step at a time.

or send me the pix that I send the value of the electrical diagram of the plate, then you send me by email.

Do you have the electrical diagram for the board v2 ?

Hi, is this the one you can control from your phone through the app, and also can I have the PCB file as I need to get one however your ebay link does not work. Thank you

Is it gonna work with Home Assistant?

The flasher tool link doesnt work

heo, may i know what widgets do you use for the foot pressure display as the angle measurement?

hello. wanna ask, why did you connect the rx and tx to other pins instead of the 0 and 1 pin on the arduino?

Thank you so much, I had a problem with a project and thanks to you I've found a solution !

Hi the switchpin define as D3 or D6 i try but cannot works.

I need 12 volt switch

Any one know the amp draw of this little unit?