Видео

Good work

Hello Cedric I'm am a beginner in car amplifier repairs I'm trying to repair a 4 Chanell car amplifier it has a x over switch from lp ,hpf,full that is broken on my amplifier and I cannot get the same switch can I join the pin outs of that broken switch to ch 1 x over will it work out the broken x over switch is for ch 3 and 4 any help will be greatly appreciated

Hello! I have a question. My amp keeps blowing mosfets. As soon as i turn the amp on the mosfet blows . I have tried changing all mosfets but still the same problem. Its the output mosfets. If i only use 1 of the outputs to speakers the mosfet does not blow. But as soon i try the outher output it blows again.

I can’t see the reading on the multimeter

What type of power supply are you using?

What type of power supply are you using?

You’re a beast! 👍🏼

😂😂😂 you’re right, even the slowest get it, i’m a little slow and i am understanding everything perfectly!👍🏼🙏🏼

Wow this is one of the best videos i have ever seen. 🙏🏼

I have a question,what is the name of the tool you’re using to power the amp ?power supply ?

Hello! can you help me? I have a problem with one of amplifier, sine wave output is in the noise (noise is 0,520v wthout any signal) (replacing change amps can (but too cant) help for a moment with clean sine wave, but after 1-5 minutes sine is back to noised sine wave. What is causing this problem? RCa input is clean. After my test with third amplifier, for a moment i got better sine wave in second amplifier, The problem: Amp blowing speaker much before distortion output, bass is weak / weird, flexing car but i dont hear and fell presure, Wave sine on out amp is rippling like Phase reverse - back normal - reverse - back normal itp. In warm temperature sound (bass) can be much better for a few minutes only. Or sometimes multipe disconect power wires can help back clear sine wave Which issue fits this problem? Input noise, Resistor noise, Thermal drift. And how to solve this problem. Thanks!

Thanks for the video keep it up

I have 12 power supply do i need to connect the positive and rem wire together to turn on the amplifier and connect negative wire alone infront of the amp

Thank you for this video

My amp powers up, then the protect light comes on and the amp turns off. This repeats until I pull the power. I havent opened and metered yet. Would this be the same as the amp in your video?

What causes the transistors to short in the first place? So i bought a used 4 channel amp and it would only ever get hot where one pair of output transistors mount against the amp body. This was during bench testing before installing in car. Sometimes it would overheat just by powering it on with no load, sometimes it wouldnt overheat even under load. After installing in my car, the same transistors got extrememly hot in seconds so i shut it off. Then the next time i turned it on it didnt overheat. Finally, i started my car and drove it 100 ft to my shop and by the time i got there the amp was stuck in protection mode. Took it apart and found the transistors for one of the channels were shorted. I ordered replacement tip35c and tip36c transistors but im worried they will overheat again.

Good job keep up the good work nuff respect 🇺🇲🇯🇲👍🏽🙏🏽

good to learn . i just came across your channel . i would like to learn . can i email you ?

Nice video very helpful yearn to learn!!❤❤

Well done bru thought me alot .keep posting videos

New skar mono block amp running two subs sounded great at first with more bass than I ever had. One day with no changes it’s like I lost half the bass I had been use to. No protection light I replaced subs and still no better. Took amp aprt and there’s three green resistors burnt up. Any ideas or tips?

Thanks for the video. Take care.

I gotta say this was a very enjoyable video to watch, my amp stopped working last week and after I watched this video I took my amp apart and fixed it, and it worked. You did great, right to the point, funny and nice. You’re going to do great. Thankyou

If car head unit is stuck on boot loop, where should I start? There is power, no obvious burning on the board, no obvious damage on parts? I have Toyota entune radio unit. Thank you for you video

Good job ❤

Thanks for sharing your knowledge, I ran into your videos since week and I've been watching since. I love how you break things down and show the settings on your meter and a clear view of what you touch along with explanations. I wish the best for you and your channel. Thank you

What if only subwoofer don t work? It s car s subwoofer , from the factory. Suddenly stopped working. How would u fix that

So the generic mosfet is 55v? I have the IRFZ44v is that generic? Do I need to replace with the same or can a generic mosfet work? Thank you

My amp layout is different it has only 4 mosfets on the left and 2 on the right side. Are all 6 dead? Or just the left sides Mosfets dead?

I repair appliances and amps my self

Does the mosfe look shorted or is just shorted

My problem is there’s no light, the fuse blows every time… it’s probably fried??

I learned a lot from this video keep up the excellent 👌 and

Good evening sir, I would like to ask how do you modify Computer power supply to supply power to Car amplifier?

Nice, PERFECTION, Thanks for sharing and teaching, you just got a new subscriber.

where can we get transisters from

Very thorough explanation! Great job , thanks for your time!

Hello My audio is working fine and suddenly went all mute I can ship you the amplifier. Please share details

Nice video

Great video, it was very helpful with my amp issue. Not a lot of good help on the internet for amplifier issues honestly so thank you very much.

How would I find the equivalent of my transistor? I have a 1000w pyramid arctic series amplifier and one of my transistors shorted. It says NC50N06 on it

Thanks for this Video!

Do you have Wats app or Instagram so i can show you my amplifier bleez😢

can i put whole motherboard to oven for a little time maybe fix?

Help me figure out my issue, it goes into protection mode when I start playing a song.

Awesome job bro Im trying to learn something about repairing amps . As I have pioneer old skool amplifier GM 3400 has no sound .

Hello, I have an amplifier that has been subjected to reverse polarity. I’ve opened it up but not sure how to go about what to test. It has power but very weak sound, what can I do for process of elimination to find the fault?

Straight to the point

Good evening sir please can you assist me how to join community