Видео

So you made a new scroll, who cares. You didn’t show us how you set the feeds to get it done. Also that lathe was turning real slow, slower than any back gear that I’ve seen. I watch these videos to find out how things are done. I don’t need to see repetitious videos on regular turning, they can be speed up.

3 day working

j aime bien ces video mais ces les ost. d annonce a tout les deux minute et je ne veut pas payer ,,,

Strange, we grind before we weld, but then again they drive on the left also...

Станок ,болгарка, тиски, плоскогубцы даже щётка всё новые. Студия Пакистанфильм приобрела новые декорации

wow a clean shop i didn't think id see that funner when its dirt floor on the side of the road though

Merci beaucoup you r ingénieurs good nic

....nur gut,daß sich die Achse beim Schweißen nicht verzieht......😅

Verdaderos maestros

Muito bom mais tem um fio de rosca mais grosso do quer os outros fios

Só faltou testar

Olha essa camisa de mangás compridas,

La verdad no entiendo para que hacer tanto y tan bonito pero tan incompleto la verdad noce como se le pude llamar maestro a una persona que solo enseña una parte mejor no empiece algo que amedias ban a dejar asi seran los trabojos que hacen la verdad no teajsria con ellos

¿Ése tornillo funcionó?, parece que la creación de la rosca fue fallida.

V.good work

V.good technic

Nice work Ustad

those who say this is good work do not understand machining. All this work and a few steps in measurement could have produced a decent repair. He cut way too deep with the threads. He should have gone to a specific depth with the initial boring operation for the minor diameter of the thread and verified with a micrometer. this number could have been taken from one of the other jaws. then while cutting the thread , he should have been dialing in to a number, while placing the screw in the jaw until the number matched perfectly again checking with a micrometer measuring the screw placed in the thread to the opposite side of the jaw after verifying distance to the side slot. Every thing comes off that side slot he didnt even indicate the jaw prior to machining. this guy actually was using a disk grinder on the flat side of the jaw after welding. thats the whole precision of the chuck. notice how they didnt show You how it fit into the chuck after repair so we could really determine the quality of the repair. All this work and for 10 percent more time it could have actually been done right. You are not fooling Me with this bad work

Good work in lathe and tool making sir I like it very nice job 👍 ❤❤❤❤

Good work on lathe keep it up

Good looking but zero quality

Nice tool and great work on lathe bro 👍👍👍👍

И чего только индусы не придумают из арматуры сделали быстрорез, Нобелевскую премию немедля!

Sometimes pakistaner do good job

ਇਸ ਮਸ਼ੀਨ ਵਿੱਚ ਪਾਵਰ ਲੀਡ ਸਕਰਿਓ ਨੂੰ ਦਿੱਤੀ ਜਾ ਰਹੀ ਹੈ ਨਾ ਕੇ ਮੇਨ ਸਪਿਡਲ ਨੂ ਚੱਕ ਨੂੰ ਲੀਡ ਸਕਰਿਓ ਦੁਆਰਾ ਹੀ ਘਮਾਇਆ ਜਾ ਰਿਹਾ ਹੈ ਗਰਾਰੀ ਰਾਹੀ

I think lead screwis driven by moterand chuk was driven by gear from lead screw

no gloves, even welding .. tough guys

they even save the wasted welding rods particles.. amazing

हे ब्रो यह सेल्फ सेंटरिंग चेक आपने कितने का मंगवाया है कितना प्राइस है इसका और इसे कैसे मंगवाया था प्रोसेसबताएं प्लीज

It’s so funny how many people complain and say it won’t work. It works. Been there done that. Once done it’s stronger than new and will break somewhere else. You will get a stronger wild if you remove the contamination first. Other than that it’s fine.

Muito bom...

Miracle....after watching this video I will turn Mild Steel in to the High Speed Steel Thanks secret materiallogy.

Ну нечего страшного скоро очередной ремонт! Они же любят кувалдой колотить по деталями

Buena opción cuando en el comercio no se consigue la herramienta, pero si tienes un torno , soplete y posiblemente muchas herramientas más bien puedes comprarla y evitar la pérdida de tiempo y gasto de gas y es probable que sea más barato comprarla.

Não da amigo o material é muito diferente.

Да ну нах сверло из конструкционной стали 😂😂😂 аля кетай 🤣🤣🤣

هذه المحاورضعيفه لوكانت بالمستوى الالماني مارأيت ذلك

youtube.com/@thaaiveeduchannel?si=PZGilLeirknd_181

Good work 💯👍 I like it Sir 💯💯💯

بالاخره کد این تسک چیه من نفهمیدم هرچی زدم نشد لطفا کد را بگزارید ممنون❤❤

Amazing work and ideas drill and thread tap making great

Great work bro keep it up 👍 interesting video

I guess he needed a drill bit just for drilling holes in cheese.

المفروض ان يتم استبدال كامل تيوب الَاكس. ووضع القطع السليمه من التوب القديم وترحيلها للتيوب الجديد

I would have already gone to the store 10 times to buy a new bearing.

Pretty drill- for wood or plastic.

Drill rod and rebar- not the same. No matter how you heat treat them.

Ustedes son lo mejor del mundo para trabajos manuales

каким образом он закалил эту сталь???Она не калится-пипец.

Butter drill？