Видео

🎶 If yer gonna be dumb, then ya gotta be tough 🎶 😂

Notice any difference with power?

How is this press fault? Its a simple tube, there is no engineering behind it. You fouled it so it clogged. As simple as that.

❤❤❤❤😂🎉

This guy has a potty mouth!

Recepie please? 😊🎉

Calm down Karen

Hey key and remove,😢

Reminds me of building up loads for the X54R with 123gr X39 projectiles and Remington 180gr 303 RN soft points. Some of those loads required a 2X4 to open the bolt. A wee bit too hot 🔥

The old Nagants shoot better than one would think.The M44 is my favorite.

Did you get it to work

To each, his own. But that trigger looks horrendous.

You can’t teach stupid 🤦‍♂️

If I give you my address, will you send me G3 piece by piece within 2 months?

You shouldn't store the ammo bullet side down if its not crimped

It's like watching a child throw a fit. Cringe

I have 2, 1 for pistol and 1 for rifles. No real complaints aside from the last 3̀-4 primers that won't slide that I have to pick. But this guy shouldn't be reloading.

You plugged the primer drop tube and now you are complaining about it gets stopped up

Foul mouth

You quite obviously don't have the knowledge or patience for reloading. So many mistakes on your part. Just buy your factory ammo. Good luck to you.

the fk is this shite

I got to take my psl to the ramge today. Perfect start to the weekend

Also they have 20 round magazine for the psl. I love mine got it at Atlantic firearms

I haven't had my psl long and my range only allows brass and they only thing i could find was yougo heavy ball ammo and it seems to be picky sometimes times. Would the kns piston fix this?

Awesome

The bolt velocity on a G3 is already fast. I've seen a silenced G3 clone tear the back of the receiver off. The bolt hammering on the stock pulled the takedown pins right through the receiver on one side. It also broke the stock. It was at AAC's silencer shoot in georgia in 2009 at red hill range. But I can't remember the manufacturer of the rifle.

I think you had unrealistic expectations, poor technique, lack of patients. This press wasn’t designed to match the output of a $3000 Dillion or apex. It’s never going to do 1000rds and hour. It’s meant for the weekend warrior that shoots 1000rds a month and just enjoy some casual reloading. I’ve reloaded 10000 rounds on this press and other than some minor set up issues it runs great. If you break a press then you forced something instead of stopping and figuring out why things are jammed up. Slow is smooth and smooth is fast. With case lube less is more. You can actually get a hydraulic lock with too much and rip a case head off. I still like using a pad and RCBS case lube as I get a much better feel of how much is on the case.

Let’s see how many times we can say “bro” & “fuck” in a single video! P.S. - it’s not the press & the engineering is very sound.

It's not the loader ... you do not need to be reloading... you have no patience to do it right as you go ... you gonna blow yourself up ... just go buy a box and relax or you gonna give yourself a heart attack

I also have encountered this complication, but not breaking my Orange Crusher press with use of Lee dies, even though I stupidly placed a 3' pipe on the end of the handle for additional leverage. After a small amount of sizing efforts, I resolved the complication by using graduated sizing dies; starting with one that is .002" larger than finished size. Then the final size and all are concentric when measured, with powder coating still on all castings. I suggest you order another or two other larger sizing dies for your lube-sizer, to prevent further complications or breakage of equipment.

first you gotta be smarter than the machine! if all else fails refer to the instructions!

Hi great short watch the full length video and I didn't quite understand what grain it was because of the wind but really apreacheat you work

The only thing that surpasses your ignorance is your stupidity of a simple machine, you need to have your pampers changed & go to the time out corner. 😂🤪😎👎🏻

WHICH KNS PISTON WOULD I NEED FOR A POLISH HELLPUP CHAMBERED IN (7.62)???

heat the plastic tube slightly and shove it on. then it will hold 450 small primers. but when you don't pay attention and jam it up, you use a empty plastic water bottle with a small hole in the bottom and shove a straight coat hanger up to clear the jam. and all the primers fall into the bottle. once you clean out mess, maybe a little brake cleaner. use a 3/8" allen wrench to back off the expander screw which will close shaft and allow you to reassemble. I am also a lee 6 pack owner for 4 weeks and have loaded 6,000 9mm rounds. I have had a couple issues, but they have been fixed with a little thought.

How'd you let it get so backed up with spent primers?

I don't know about pouring lead tainted water on the dishes in the sink.

Hello, I suggest loading the cartridges very lightly and removing the rolls, that's how it worked for HK. greetings from Germany

First Cuss much, second that got nothing to do with the lee 6000 that you sticking way way to much lube on cases more not always better. I run around 5000 rounds threw my lee 6000 from 223,9mm,38 spl 350 legend and not a issue my rifle brass I do before it runs threw press I use universal decapper than resize than threw tumbler after check length etc. Than into press to finish . Lee die set just happen to come with press there not actual a part of the press. So I understand your frustrated but it not a fatal flaw with press

Odin is proud Lord Nelson

Lol😂

😂😢😢😢😢😢😢🎉😢😢

Lee sucks. Period.

All I can say is should have bought a Dillon Precision press.

Just blow some compressed air in and confetti cannon them primers out. As for the primer catch tube I cut down a 12g hull and roll crimped it to fit in between the linkage to hold more primers. I agree that Lee has made some real boneheaded decisions over the last few years.

good

I think the reason you're getting lower weighted projectiles is because the printing press alloy has a lower percentage of lead in it. The extra antimony and tin is fantastic, but cast straight there's a bit too much. Many people mix pure lead in with their linotype alloy so that it casts heavier, is a bit softer, and it lasts longer. You should be able to find out ratios searching online. Hope that helps!

How'd it go? I'm currently working on dialing in a TM42 on my KLR 650, installed it and had it running but it's way too rich so I ordered different jets and a smaller accelerator pump nozzle.

Awesome