Видео

@@andersonluizvidi7267 Share email id on Instagram.

@@luongcuong1582 Hello Friend, To add any new device in your TIA program you have to install the GSd file for the devices. Then only it will reflect in TIA hardware catalog. Have you added GSD file for your drivea in TIA?

@@zackk_54544thanks for your response. My question is not related to gsd file, so I have find information in google and know that I have to install Start Driver Software to use same function as your video.

@@luongcuong1582 That's good friend you know about the starter installation. In case if you dont have starter installed you can perform the application by installing the GSD as well.

@@srpskisabor Hello friend, Check out the dataman software help section. Pdf is available there including tags excel sheet. You have to create the same in your program. After successful communication with your dataman. Same tags will be used for further operation. Note Addresses in the hardware and the tags sheet must be same. DM on instagram for further queries.

@@nithish.6663 Connect on the Instagram channel for better understanding.

@@tusharshigwan4904 DM 302 has been used in the video. You can checkout the dataman website and choose barcode as per your application.

@86francho Hola amigo, conéctate en Instagram y cuéntame más, ¿qué quieres hacer exactamente?

@@danipranata9161 which software version you have installed?

@@zackk_54544 i done it, it just need a little configuration, but right now i have another problem, my fc 302 drive cannot start, even though i can change the reference speed, no error occured.

@@danipranata9161 kindly share your mail id on instagram.

@@vascoguimaraes6693 Please share more details about your conected devices and errors for better understanding. You can also connect on Instagram.

Hello, Sample program will help and guide to write the porgram to read barcode successfully.

@@zackk_54544 Its not working for me :/

@@zackk_54544 Phisically do I need to put the trigger wire on the output of the PLC ?

@@zackk_54544 My trigger done does not activate the sample read

@@Reaper0931Yes you have to connect. Either use external trigger via connected sensor etc. or use trigger wire.

Hello, these blocks are to be used for both profibus / profinet communication.

@@zackk_54544 okay, thanks

For more queries connect on Instagram All the best

Siemens blocks has predefined bit structure for control/ status words. We have to follow stuructre to read /write the data if we using those blocks. For more queries connect on Instagram.

@@zackk_54544 :I went through the manual and found that the format is as mentioned by you 🙂 Thank you.

Share some more details I didn't get you.

Normally, device name assignment is made in the Hardware configuration section. You didn't but it worked. Why don't we need it here?

That's true. Definitely we have to assign the device in the hardware. We did the trial with only one drive and its working cause only one device is in the network so it has automatically assigned. It doesn't work when there are multiple devices in the network. We have to assign each them.

You can connect on Instagram for more queries. Thanks

Thank you a lot!

Send your email id will send you over there.

@@zackk_54544 please send this I need urgently

Sb18963

Saa raa nsh 3 @

You remove space and its gmail id

Hello Friend, I have not used that SINASPEED block, but as per the block description mentioned in help section I guess we can use it instead of using DPRD_DAT & DPWR_DAT blocks. Main difference is only standard Telegram 1 can be used with SINASPEED. Also, No need to mention all variables in data types but make sure you use the right bit to turn on as per the bit addresses. You can check the help section of the SINASPEED block. Variables are necessary to be defined in the data types If you use DPRD_DAT, DPWRDAT.

If your application does not required much functions go for the SINASPEED and share your feedback. For more queries you can join the Instagram handle. Thank you

Thank you for sharing feedback Mr. Malik. Do share your ideas as well, on which you want informative videos.

@@zackk_54544 well i would like to request you to make a video on a motion control as well.

@@fazimalik5214 Noted, will share the video on topic soon for sure.

@@fazimalik5214 You can also share more specific details regarding your application if you want. Also join the instagram handle as well.

GSD files you can find out on the Dataman website also if you have installed the software checkout the help section in the software.

Not available

@@chandrakeshdubey4577 support.cognex.com/en/downloads/detail/in-sight/4711/1033 Please find the GSD on the above link.

​@@zackk_54544thanks

Yes friend , To run the application we need Danfoss drive in real.

Please share what exactly you want to perform?

@@zackk_54544 I see. By the way, I would like to know if there is a way to make a profibus simulation like this without a real VFD. A simulation with plcsim

@@zackk_54544 I see. By the way, I would like to know if there is a way to make a profibus simulation like this without a real VFD. A simulation with plcsim

Watch out the video in the link below. ruclips.net/video/hE4F6CyAL_c/видео.htmlsi=X1QmFKMqjhEoRGNu

Thankyou for your feedback. Kindly share the complete details regarding your application. I didnt get the S120 drive, share more information. If you are looking for siemens G120 C drive. Please is already available. You can also connect on instagram and send Direct message there.

Link attached for Siemens G120 C drive communication with siemens PLC. ruclips.net/video/vWVW0s2eY4w/видео.htmlsi=-KCgK4tLURYO4vm5

You mean link for Fc360 profinet GSD file?

Here is the link for profinet Gsd file FC360. support.industry.siemens.com/forum/in/en/posts/gsd-file-danfoss-fc360/209592?page=2

Hello there, If you have sample program use as it is, no issue with that. Make sure that the addresses of Inputs / outputs are used correctly.

For more help you can send DM on the Instagram channel as well. All the best👍

Send me your mail id or DM on my insta channel. Will send you the GSD file for the same.

Profinet Gsd file is not available on Danfoss website. Either you should contact danfoss so they will provide you or provide mail id so that someone can share the file.

support.industry.siemens.com/forum/in/en/posts/gsd-file-danfoss-fc360/209592?page=2

Hello Friend, No video has been uploaded on profibus till now. Will make it and upload soon. Meanwhile join the Instagram channel and send your application query on the DM. Thankyou

Hello Friend, Here is the link for the video on profibus communication. ruclips.net/video/6rOWUrMELdE/видео.html

Dear Friend, please share complete details of your application which you want to perform with adapter. You can also DM on my Insta channel mentioned.

Waiting for your response friend.

277 defined for telegram, 278 defined for parameter access point but to execute read and write operation words defined only at 279. Hope you got your answer.

It happens soemtimes. Check you cable connection. Check your laptops IP address series. Make sure IP address range should be as 192.168.6.0 series. Recycle the cognex power.

Hope this will work. You can also share your feedback and your queries on instagram channel zack54.automation.

@@zackk_54544 yes bro its work but muze mene kr liya tha ip dubara se set krke

Surely. Will share the video for your configuration soon.

ruclips.net/video/hE4F6CyAL_c/видео.html

WATCH OUT THE VIDEO FOR RS485 COMMUNICATION