Видео

My 2012 Honda Civic coupe is different than your Honda Civic sedan. The window switch panel is not removable by itself. It looks like I have remove the door panel first.

Is that death line between cylinders? Look, this is 100% done on purpose to make engine not last long time. That's the reason for all of these 1.5T failed gaskets. It will last, but eventually it will blow because of very little space between cylinders and that cut line between cylinders.

Thank you for the great video! I'm 47 and ashamed that I've never heard of the spill free funnel yet ... or how to fill a radiator properly for that matter, haha! Well done sir.

❤❤❤

Thanks for sharing your experience. I have 2022 honda accord and got dash light blinking A (auto start/stop idle) near the speedmeter. Can you tell me how to solve this problem, car is running fine

Does this have to be done with the vehicle leveled? Or can my vehicle up into a ramp for easier access to the drain plugs?

Thank-You so much for posting this video.

Very nice video. Liked the way to remove the parking cable bracket from the caliper. Thank you.

Thanks

thank you much 🎉🎉🎉❤

Mine was $40 after tax

why the put them shit missions on them

Man so easy! Crazy places charge $50 to do this

Thank you!

Is this process the same with a Honda accord 2018?

Problem Solved ! Thank you !

What about the two red lights at the bottom, and left and right sides of the rear bumper ?

Bulb sizes would have been more helpful

Ridiculous, Honda there should be a recall to fix this nonsense. Will try later,

I solute you for this video 😂. I drove my 19 odyssey 1200 miles nothing was changing on I/M but after watching your video it green in less than a minute. Most of the Honda techs with service advisors are TRASH!

Thanks bro , I have been driving my CRV from last one year without adaptive mode , after watching your video , it’s took only one second 😂

What is the tool for the screws you use ??

Thank you

(2011-2015) Chevy Cruze.

Best demo ever. Thanks

This also worked my 2019 Honda odyssey’s not pass inspection but i see this video and I try so is pass today thank you for helping me

I was surprised I could contort myself into position to do the replacement. I didn't have that ability when I was a teenager, but can do it now because I'm in much better health, no thanks to local doctors. Pulling the floor mat out of the way, putting a carpet remnant on the ground, using a mirror, as well as a small flood light really helped. Thanks for the video! It made the process easy to grasp. Fortunately, one of the local NAPA stores had the blower.

Like it

I drove my Honda Pilot 2021 about 1000 miles but still it was not ready for inspection. I completed multiple drive cycles but EGR won't be ready. I followed your instructions and it worked. Thank you very much.

Chrysler uses aAtF -4

Where'd you buy the replacement. Have a link?

Whats the air cabin filter i need ?

Thanks you

Neat

Thank you! Winning!

Thank you so much!!!!

Are all the screws the same??

I have a 2020 rigdeline and I still can't recommend some recommendation

I just came back to say thank you 🫡

I sometimes use a torque wrench to remove lug nuts to see how much they are OVER torqued. I helped a young man from Canada switch over from snow tires. His Corolla had a really low torque spec. like 83 ft. lbs. They were close to 250 foot pounds, and yes, hard to remove. This can warp your brake rotors from the excessive pressure. What's worse was the studs were coated with grease. He said that corrosion in Canada would eat up the threads without grease, and that his dad was an engineer. Dear old dad was greasing and over-torquing all of their cars, for Safety.

How long actual time to r&r this ? Thanks.

does anyone know how to find a similar clip for the under-seat wires? Or should I just settle for a zip tie? it looks like they arent reusable

For which engine is this?

👍

Good morning Nice añd educative video. I have question to ask í bought a used Toyota Camry 2006 and í discovered that when I drive for 2 mins and press the brake it will make a loud sound . I think the sound is from tyre area. What should I do?

I have a 2024 corolla se. I took off the 18 alloys and put 16 steelies on. Look and ride better imo.

What the mechanics have done to me is break the capping that goes over the lug nut. I hate that they make two piece lug nuts. When they break off the capping this now changes the size of the lug nut and the lug wrench that comes with the car will now be to big for the lug nut. So, if I were to get a flat my lug nut would not be able to remove the lugs with the broken capping. I just got tires at Pep Boys and they broke the capping off of 4 of my lug nuts. So, now I have ordered 20 new lugs nuts that are one piece, they have no capping. This is the second vehicle that I've had to replace the two piece lug nut with 20 new one piece lug nuts. Have you seen the two piece lug nuts I'm talking about?

Thanks for the video! I found those clips for the connection on the fuel injectors can be left on & just lay the bundle aside to avoid having to disconnect & possibly breaking the clips. Thanks again for a great tutorial!

You are the man. It stopped working a few days ago and now it works again thanks to your tip. It's a must have on a car, makes driving a lot more enjoyable. 👍👍

Anyone experience the differential grinding/vibrating after the oil change? It wasn’t before and now it is