- Видео 8
- Просмотров 61 600
Sailing Chasing Summer
США
Добавлен 15 фев 2016
Just short videos I've done while building and launching the boat. Maybe some day I'll shoot longer footage and upload actually sailing adventures.
You can view more content on my Instagram page: sv_chasing_summer
You can view more content on my Instagram page: sv_chasing_summer
Launch and sail to San Diego
One of the happiest days in a boat owners life are when you first purchase your boat ... The second is the day you launch her.
Просмотров: 138
Видео
Motoring out of Oceanside, CA
Просмотров 1782 года назад
Tuesday, May 24, 2022 I motored out of Oceanside harbor on the way to San Diego Bay.
Boat Launch
Просмотров 862 года назад
May 18, 2022 ... after eleven years of building ... I've launched Chasing Summer
Installing Flanged Groco Hull Valve Part 2
Просмотров 5484 года назад
Sorry, Microsoft deleted Part 1 before I could get it uploaded. That video showed marking and drilling the hole. This video shows installing the valve.
Patching an old thru hull
Просмотров 58 тыс.5 лет назад
Patching a hole where I moved a thru-hole. This video is intended for solid FRP hulls, not cored hulls
Finally a video that shows that you put the largest circle on first and an explanation why. Also like the idea of wetting most of them out on the bench. Thank you!
Dude, wear a mask
hiw did you patch the inside?
He did it completely backwards. Always start with the small patches, that way every new piece is bonded to the original glass around the edge. The way he did it, ONLY the first piece is actually bonded to the hull. If that bond fails, the whole patch falls out in one chunk, because only that one even touches the rest of the hull.
Doesn’t matter which way you do it.
Did you flair in inside of the hull at the same ratio, or just enough to get some glass on it? I have a thru hull i'd like to fill, but it's not in a good location to flair the inside. Thanks.
Thanks for this video. I definitely learned a thing or two! Next time we haul out I want to be a little more hands on instead of having the work done.
Is it necessary to make a taper?
Yes the taper will give u more surface area for your patches to stick too. And you can build up more layers making it stronger and not go above the original hull.
Epoxy over Polyester, never Polyester over epoxy....
no kidding .. I only use polyester on the boat.
Great video. One piece of advice though. Always let polyester cure a good two weeks before applying epoxy. That’s one of the downsides of working with polyester, as is the weaker secondary bond.
awesome patch man.
Marvellous to hear a sailor who can read! Waay too many call it BUY AXLE instead of BI AX I AL !
My video of drilling through the pad got lost by Microsoft when they did an upgrade on my system :-( sorry.
Great video. Thank you!
Hi mate ive watched this video twice i have a thru hull tranasducer hole to fill and repair and like you i will be fighting gravity ,with my limited work area it means i am under the trailer while i do this have cut a hole in the floor where i will apply a layer or two of csm then grind the underside and ill probably only do a few layers at a time rather than have the whole lot move on me and end up doing it again as i say i am fighting gravity great video for someone like me who has neverhad to patch a hole in a hull ,oh and polyester is my choice like you because the whole boat is made from it .
Just got email notification. Hope all went well with the patch .. glad I could be of assistance.
Doing three thru-hole patches as a first timer, so I was eating through every second of the presentation. Thank you for your work in putting me in the know-how when others in PR just won't be available during holidays to assist, or having me wait for 4-6 weeks with no guarantee that they will get to me after that time.
Great vid, tried your method today, worked well. I was a little low after the patch so I kinda faired it with peanut butter resin\cabisol. faired it out today and it's looking god. Thanks for sharing.
Thanks for posting!
Nice job! Thanks for sharing
Ty
One of the few guys doing it the right way.
I appreciate the creator's video and seeing his technique, which employs a method similar to an instructional video by Jamestown Distributors I watched recently on patching holes. I'm new to all of this, so I won't argue methodology, but on a side-note, I heard the perspective on the other approach (small-to-large) that justified that method, as well. Interestingly, that method was validated by some people who had been trained in fiberglass repair by the Navy as well as someone in commercial aircraft manufacturering. Thee rationale for the small-to-large approach is that each layer makes some contact with the hull and the new fiberglass runs paralell with the original layers, which they say is favorable when considering stresses from an engineering perspective. I'm sure that quality work, properly mixed quality resins, and otherwise good materials will ensure both methods wont ever present a vessel integrity or safety issue, so I don't bring this up to be in disagreement, but I do find it interesting that these two opposite methods each seem to be fairly common.
Great comment .. I'll stay with the large to small. You can't tie into the original long strands anyway so if it's a matter of stress the patch is only as good as the bond of the first layer. After that you're just building up thickness. I do alternate with bi-axial for local strength.
Great video! Nice to see some professional work for a change! I have done thruhull repair in both polyester and epoxy. I know everyone swears by epoxy, but the second boatyard I worked in, did virtually every repair in polyester including installing a bowthruster in a fishboat. The secondary bond is not as strong as epoxy, but it is usually good enough if prepared properly. Looking forward to your other projects.
Can gelcoat bond to epoxy ?
1.10.21 A very clear demonstration of how to grind, taper, patch and fair your thru hull fitting. How about some hull blisters next time? Best wishes! Hector
Nice work!!