Видео

Didn't work Frustrated right now

R

How can update de chip list names ?My chip si not show .Any idea ?

I love my thinkpad. I keep this as a backup in case my main computer pops it's clogs.

Bert Good video. Normaly i dont comment. But This video helper me a lot

I have 800 G9, there is no jumper on board, But there is yellow button please help me how can I do it? I tried to only press yellow button, But nothing happen! Help me

I'm stuck with the EliteBook 800 G6. There are two small holes (not the classical jumper) and the CMOS button...what can I do to get the BIOS Reset? Thanks all!

What's the dc voltage needed to run this board, if its possible...plzz reply

I can use xeon?

Would it be to much to ask for you to explain what you are doing and why

Can you do a Elitedesk 800 G3 SFF

Why did you put the RGB fan on it the wrong way around?

I had the same problem with my JBL, and with the help of this video, it's solved! Super!

Chào bạn. Tôi làm đúng theo clip bạn hướng dẫn. Có tới 3 loa vệ tinh có tín hiệu nhưng âm thanh rất nhỏ. Bạn có thế làm cho 5 loa vệ tinh phát âm thanh ngang bằng nhau được không?

5300?

Just remove jumper, booting, go to Bios Setup and security. Go to setting password, when error jumper is displayed, put jumper and define new password. Not remove battery.

any idea how to reset bios pass on HP EliteDesk 800 G6, it seems like there is no jumper on g6 version

Bro, ami no me aparece el apartado de boot mode para cambiarlo a legacy support y lo tengo primero al usb pero no me lo tóma, porque será??

OMG thanks

Its work! Good tuto

Thank so much 🎉❤

Mksh mantap

All I had to do was try get the padding off on the side that didn’t work and now it suddenly has sound again

Followed every step and it doesn't work

УДАЛИ ЭТО ВИДЕО И НЕ ПОЗОРЬСЯ. Все твои действия неправильные Развинчивают и завинчивают радиатор на процессор в последовательности по цифрам которые нанесены рядом с винтами, 1 2 3. Если так кляксу термопасты в центр нанести, в таком случае не будет качественной отдачи тепла от крышки процессора на медную плоскость радиатора. Охлаждение процессора и отвод тепла будет слабым. Слой термопасты должен быть ТОНКИЙ и по всей площади крышки процессора. Для этого пасту наносят не в центр крышки, как это сделал ты, а на край крышки, полоской с высотой 1 мм. Специальным пластиковым шпателем растягивают слой пасты к противоположному краю крышки процессора. За счет этого слой пасты станет тонким. Задача термпопасты занять все неровности на крышке и слипнуться с медной плоскостью радиатора. При этом оставаться тонким слоем. Чем тоньше слой термопасты, тем лучше теплопередача между металлами соприкасающимися друг с другом через этот слой. Ты ПРИНЦИПИАЛЬНО не понимаешь всей сути нанесения термопасты и для чего она должна быть. Дальше, вначале укладывают салазки блока вентилятора в пазы корпуса, а потом соединяют его клему к материнской плате. Ты сделал все наоборот с риском случайно задеть провод присоединенный к материнской плате, когда целился салазками в пазы для установки вентилятора. И в конце видео, ЗАМОК на корпусе застегивают, что бы крышка не слетела. ИТОГ --- Дизлайк Не рекомендовать Жалоба в Ютуб за ложную информацию по замене процессора и сопутствующим действиям.

Can we upgrade i5 8th gen in this pc?

Need help please: I do the same steps with my prodesk 400 g3, i want to upgrade from i3 7100t to i7 7700,but the system make sounds of error, and whan i look for the problem in hp official website, i found that the problem is of the lusted below: then four times, the white light flashes short (3 long red, 4 short white) This condition indicates a possible malfunction of the power system. Reduce to the minimum configuration (CPU, system board, power supply, 1 DIMM) and isolate the failed components. Reduce further if the problem persists. Test your system using a known, good power supply. Contact HP Customer Support for further assistance in replacing the component, system board, processor (CPU), or CPU module if the problem persists

THANK YOU!! i cried a river for this but it's working!!!!!!

hello..i have a M700 with i3-6100T...what would be the best processor I could upgrade to and is it worth it? Thanks for answering

Hey, Brother! I currently have the Xeon W-2123 processor in my Z4 G4. I'm looking to upgrade. What would be the correct upgrade?

very helpful.

mini 800G4 worked. Thank alot Bro

Upgrade , only disconect the jumper and normal turn on then press F10 , only this.

Such a simple solution, just cleaned it and they're good as new, thank you so much!

Do you have the bio bin file

Keep up the good work!

i have question! The m700 model has a core i3, is it possible to place the i5 or i7 processor?

What PID did you have?

Thank u so much

i have these headphones many years. this problem started like 2 years ago. I read somewhere (on internet) to connect them on the charger, disconnect them and the second will work too. Wasnt something risky so i did. It worked until now. But it wouldnt work anymore. So, i tried what this video said. YES, IT WORKED. THANKS SO MUCH!!!!

Sir, what type of processor is it?

temps problems?

I did this and the PC is constantly thermal resetting whenever it gets a heavy load. This is even without disabling the throttling.

Buna ziua....As ruga pe un specialist in domeniu, sa-mi spuna ce fel de tranziztori power mosfet se folosesc in etajul final in clasa D al mixerului amplificat Dynacord Powermate 1000-3.....si eventual de la ce firma, producer.......Va multumesc

Great 👍

What was the tool and sportwear used ? and where can you get one

سهل جدا وشرح مفيد . شكر لك Very easy explain and very nice thank you very much

Partion mbr or gpt

Arguably the shittiest and slowest laptop I have ever had

my computer not reaction witch f12