Видео

Maybe the adjustment is for the 3.6

Thank you!

7 years later we have camera glasses!

Just might have to try this out. Just got a zt2 50”. Great video

Added mine yesterday. I order off Amazon, did it just like you shared. Left the rubber on it and dam does it improve the ride!!!

Looks really good

Just got my cub last week and bought these springs then went to Lowe's to get them washers and hex nuts. Ride's alot better now, I also lowered them psi's on the tires. 🙏💯

Man I just bought the 54", and love it but is beating me up. I got to get me some springs

Are the springs still working or have you tried a different seat modification?

Nice mod! Just junk the factory bumpers and use 3" Harley springs 😊

Thank you. I’ll give this a try. I messed up by stuffing two wheels in the trunk. It closed, but will not open again. 🙏🏽.

Can you tell me what size bolt you used, and how you tighten it down, with a socket or wrench?

3:36 mine had been beating the crap outta me. Big difference. Great advice. Thanks.

I saw your video two years ago, ordered the springs … never put them on. 🤦‍♂️ guess I better get after it!

Great video. Thanks for sharing this trick. Coil springs ordered and on the way for my new ZT1. Thank you sir!

Super helpful, well explained, my waterpump on my 600 has died, so will be using this for help.

Hey Sherman, I have the ZT1 I have the springs that I ordered from Amazon. I do have one question. With the springs mounted on the seat and leaving the original seat clips in. Letting the springs rest on the old clips. Does that tend to make the seat feel like it’s leaning forward to much ?

My wife and I both use our ZT1-50". The fore-and-aft seat adjustment is semi-fixed: it has bolts, and isn't on a slide, so I can set it up for one of us, or the other one, but it's a time-consuming pain in the butt to move it back and forth. Is anyone aware of a sliding seat modification that's available like on my John Deere GT245 tractor ?

Added the springs to my cub cadet, the ride is 100% improved, thanks for the post

What noise did the pulley make before it blew ? Mines makes a noise after I let it sit for a couple hours after driving. And it sounds like clacking in front of the grill.

You can also junk the bumpers and use 3 inch motorcycle seat springs ,but you have to do something, the bumpers are junk!

Yep....just got my springs in from Jeff house, installed em and the ride is phenomenal. Only thing is the seat sits a little high, so I'm going to cut off one loop if the spring to lower it a bit. It basically threw off the geometry with my steering arms because I'm riding in the seat higher......but good fix having the conventional Spring on top of their plastic crap

needed to see this! thanks for this

I was able install the water pump properly and is not over heating. But now it’s giving me vsc system alert. It want pick up speed. It’s been sitting up for 3 months before I finally fixed it.

Do u need to bleed the thermostat after adding coolant?

YOUR DOING GOOD, JUST TAKE YOUR TIME 🫖

Update: I did get a great bit of improvement out of this spring modification. But I thought the ride would get better from a softer spring. I searched at local mower places and tractor supply and found nothing. Checked the internet but nobody gives the diameter of the spring strand. Fortunately, i was reading comments on this post and Scott Hamilton mentioned his tires were drastically over inflated. My rears were somewhat over inflated. They call for 10psi max and had 12.5 psi. I set them at 7.5 and this is much better. So check your tire pressure BEFORE doing this modification. Be very careful with the front tires; the air goes out much faster. Mine have a max of 22 psi and was at 12.5. When i tried to bring them to 7.5, it basically came of the rim at about 10 psi. I had to remove it from mower and fight for about 40 minutes to remount to the rim. Not sure whether Cub Cadet or Home Depot overinflated the tires. I thought mine was fine since they have such tall sidewalls and are not low profile which definitely have a stiff ride. Thanks for the tip Scott.

Need this motor trunk, where do i'get it. Pls advice me

My goodness I can’t see anything

So is the water pump at the front of the engine on the LS460?

My truck won’t open not even with the key not even with the emergency latch inside the trunk ?? Any help

My first ride on mine was so ruff I couldn't go full speed. My back hurt and I was bummed out. Before the next mow I checked the air pressure in the tires. The max air pressure on the back tires said 10psi. It had about 32psi!! I let all that air out, got it down to about 8psi. HUGE difference I could now full speed and my back was not tore up afterwards. Don't know if Home Depot over filled them or cub cadet. Turfing seems not as bad. I would like to still upgrade to steel springs.

Can you tell me what drill you had to use to drill through that steel?

People are dumb.6 dislikes?Why? Hes very helpful.

Great shaving video SF hoping for more. Was hoping you would let your moustache grow. Would be good to see you grow and then show how to shape it up and maintain the look. Would make good shaving video. Hope you will consider growing?

Did this help anyone?

Thank you

Mine rides a bit rough too. Thanks for the great video!

Great info man. Thank you too much!!

Exactly what I was looking for! Just bought a ZT1 54" yesterday. Holy smokes, my lawn beat the crap out of me! I just ordered these. Thanks for the help!

Buick 6T45 transaxle replacement tips mentioned too.

Thank you sir for the information. I was looking for something like this because the ride is too stiff without springs. I ordered the springs and I'm looking forward to a more comfortable mow.

Hey Sherman - just got my ZT1 With a 54 inch deck this weekend and I love it. I ordered the springs with the part number that you provided from Amazon and I’m looking forward to putting them on this coming week. Appreciate the tip! Have you made any other modifications for a smoother ride since this video? Also how about the springs - have they held up since you put them on last year?

Thanks Sherman..

My MAN!!! Going to try this thank you, happened after pulling the battery on the gs460 (had to do plugs first time and wanted the room/pulled battery ;))

وين يجي يركب سلف لكزس ٤٦٠

Good job for a first time doing mechanical work.

Nice info i just pulled my belt off and seen red pink residue Toyota colant crusted up all down the timing cover and noticed play in the pump back n forth made a whistle wine noise thought it was the tensioner or idler pulley

Right on bro! Replacing all the belts on a 76 Continental 460 definitely going to hit the like and sub before I get up out of here keep up the Great videos!

Thank you brotha for the information