Видео

Are those 18s or 19s?

What size pulley came with the kit?

what do you have to do for the mirrors to fold and the puddle light do you need a new harness with those wires i saw that you connected some but i didnt really understand much could you help me out

What drop sir?

Where do I connect the wire to the driver side for Terning signal

Are those 6.2 supercharged Ford raptor badges?

How’d you fit the front. My 17s hit with a drop on it . Are you using stock spindle .

Howd you pin it to the main harness? Im having a hard time doing this. All wire is ran but its a special connector and cant source locally

What do you have on the truck for suspension and drop bro ?

How did you fit the rears bro my banjo bolt seems to rub on 17s i believe

Where at through the firewall did u run your wires im trying to run an AFR gauge

So what happened at the dyno shop?

Is that the original intake cover?

What size rims and tires boss man

That is quite an engine swap. Good looking truck too. I installed a UPR Catch can on my 2017 5.3 Yukon after doing a lot of research I found lots of good reviews for UPR Catch cans. On my Yukon I purchased some rubber transmission cooler lines and two factory quick release fittings, which are quite expensive, and run my lines down to where the extra battery box is located and mounted my Catch Can there. Also placed plastic loom over the lines and a few clamps to make the install look factory. I bet after your engine swap your truck gets down the road in a hurry. The 6.2's have great power and much more torque than the 5.3's. I haven't had any leaks from the bottom of the Catch Can, I will have to look and see if mine has that seal like your does. Great video enjoyed watching it.

Bro nice setup props say them gauges where did you get them made thanks in advance

Epicenter 🤮

How much hp

What tire sizes u running? Looks perfect

What cam and what converter

Wassup with more vids? Lol

Yo what’s your IG? Where did you order the driver left Door master power window switch?

Installed a k&n and had no problem with mine

Nice truck bro ,can i ask where did you pull acc power for the gauges.

Sux how the filter is right about the header

I got a 5.3 and wanting to go procharged as well . I’m on a McGaughys 7-9 inch lift with 24x14 on 35’s. Everything’s so damn expensive tho 🤦🏽‍♂️ love your truck tho brotha ! 💯

Awesome truck!!! What drop do you have?

You talked and talked and talked and then 1 second vid with the wheels on lol unbelievable

En cuanto te salió

Buenas tardes amigo en donde radicas

Wheel size nd tire set up

would 17x10 fit these lt model trucks ?

I’m thinking about doing a blow through but I just remember about the pump how would you change it if it went out and you have a blow thru.

🔴 When it comes out this clean looking, whats there to argue about cutting a hole❗️

nice truck brother but its lowkey parked, my cammed 5.3 is running just like that with 4l60 and 4.30 gears with 22s

Hey where did you get the Corvette engine cover at?

i have s77s for my challenegr and also wanted a 17x7 or 17x8 up front glad to see a 255 tire would fit well

Great video until you got to wiring underneath. You were making me dizzy. Wish it was more detailed and slower. Thanks

Where did you get your wheels bro

I have a 2017 Silverado LT. Do I need that LED harness? If so, where can I buy a set?

Any update one Ltz/High country head lights!!!!. . . Btw loving the Silverado build

What is the card slot for on dash next to the door on the driver's side?

Beautiful truck what size are the back tires

Did you do anything to the fuel system man ?

Installing S&B on my 22 5.0 was a breeze compared to that

It’s purdy

What’s it make at the wheel?

I cannot disconnect the tail light harness for the life of me. Any tricks? I have a 2018

Those thermostats have the same lip that the GM one has. The other thermostats like Murray, dorman and etc, don’t have that. The spring allowing it to open comes out of place and doesn’t open properly, causing a delay. Gen V LT1 motors run hot asf. Especially if your running NGK Lasers 😭

Great setup, very clean. Is your bed cover soft or is it metal? I'm wondering if it rattles from the outside of the truck. I'm currently looking for a good bed cover for my Silverado 2500.