Видео

Unfortunately I did not start the YT channel until after the engine was removed. If you skim thru the playlist on the re-assembly you should get the gist of all that is entailed, just in reverse order. Thanks for watching and good luck on the repair! 👍😁 Playlist: BOBCAT 843; REPAIR SERIES: ruclips.net/p/PLXhqnH7y_t8T-o7nL8nNJgMWR_gRcsnhm

She's still lifting all my stuff even after overloading it with the crane pick! Thanks for watching! 👍😁

Thanks for checking out the channel! I have quite a few videos on various different projects. Cheers 👍😁

Thanks Zane! I think I caught one of his videos working on a gage cluster. I will have to check out some more of his videos. Thanks for watching and Happy Thanksgiving 🦃!

It would have been handy if those larger bolts would have unscrewed, but the Metabo doesn't mind! Thanks for watching! 👍😁

That's pretty awesome! Most might find it hard to believe, but I have been to Catalina Island! 2016 vintage. Thanks for watching and keep on boating! 👍😁

I would think it is unlikely, unless the belt is slipping enough to under drive the accessories. In particular the alternator could cause a low charge if it is slipping badly. That would be a much more evident squeal though. I recommend checking the codes and replacing the belt to avoid a potential breakdown. Happy Thanksgiving 🦃

So far it has done everything I have asked of it, but it isn't an everyday use item for me...... In comparison to an old school American made unit it's junk, but it is functional. I noticed the ram doesn't fit well in the head (it's a little sloppy) and the tool plate is soft. Thanks for watching! 👍😁

It took me two 12-14 hour days to complete the build. Add in a couple extra hours on top for rubber mulch and anchor installation. Organization is key, lay out all the pieces in order for a more efficient build. I didn't do this until day 2. Thanks for watching 👍😁

Thanks Zane! I was hoping to find a bolt on solution that was a direct fit, but couldn't find one that opened. It turned out better than expected! Thanks for watching my Friend! 👍😁

I took a gamble and bought a kit off old 'Flea-Bay' if you know what I mean. It's a major online auction site, but some implications exist for using their real name. I think they are still available, try searching 'Ford CL40 CL340 skidsteer Lift or tilt cylinder seal packing kit'. Thanks for watching! 👍😁

I used it last year for a Christmas parade, it worked well but it doesn't respond to load changes well.....I think the old carb is gummed up. Thanks for watching 👍😁

That was close to my first guess too.... She's quite a bit heavier! Thanks for watching.👍😁

If the engine isn't overfull, I am guessing the engine has blowby that is pressurizing the crankcase. Check the oil fill level, check for a plugged crank case breather, check for excessive blow bye, check for a blown head gasket. Thanks for watching! 👍😁

Thank you 'Rust Belt'...... Check out the cab replacement video to see just how rusty it was. Thanks for watching 👍😁

You should be able to use the furnace blower to circulate air throughout your house without any issues. Make sure your furnace blower motor is the correct voltage before trying to manually energize it. In a later video I install central AC on this same furnace. I installed a relay to trigger the AC and the blower at the same time via the thermostat. This is the more sophisticated approach. Thanks for watching and stay safe! 👍😁

Thanks! Thompson's Clear Sealer rolled or sprayed on. Thanks for watching 👍😁

Thanks, I would think all ignition 'key' switches require multiple wire connections. Maybe the two wire switch is the manual off ignition toggle? This one used 4 wires I believe. Thanks for watching 👍😁

Thanks! I was worried about leaks, so I made sure to spend extra time cleaning the surfaces. I think some of the issues people were experiencing were from over tightening the bolts. Thanks for watching! 👍😁

No expert, but first I would check the level and condition of the transmission oil. If it is a shuttle shift I would then inspect the shuttle solenoid valve; make sure it's shifting, damaged internals, plugged with goo and or damaged wires and or faulty limit switches on the directional control. Best of luck, thanks for watching! 👍😁

The Y directly behind the toilet goes to the sink / it has a vertical vent behind it. The main stack also has vent straight out the top before it exits. Thanks for watching 👍😁

Sounds like a nice performance upgrade! I think the customer wants to keep this looking original, but I'll mention it to them the next time we chat. I think the brake hoses might be suspect. Thanks for watching! 👍😁

I did not perform a reset on this Fusion. It didn't have a phone connected to the Sync and I'm unsure if disconnecting the battery requires a reconnect? Thanks for watching 👍😁

Best helper / student! I hope he doesn't get spoiled since his first brake tutorial was on Dad's fancy lift! Thanks for watching my Friend! 👍😁

Thanks! I now have all the specialty tools for drum brakes, yet still manage to pinch out cut myself while working on them, pretty much every time 🙄. Thanks for watching my Friend! 👍😁

Is a Lincoln better than a Ford? It was a rubberized 'tar' based coating and of course 2" foam board is better. It's also quite a bit more expensive......1000% amateur with no desire to be a professional foundation repairman. Just a guy with some tools. Thanks for watching! 👍😁

Hard to believe it's been over 3 years since I smashed it.... It's almost back to normal, but not quite. Thanks for watching! 👍😁

I would have been able to smell the diesel.... Some premixed 2 stoke fuels are dyed red

~$600 with the light, thanks for watching 👍😁

He pulled himself right into a battery powered unit.....Works for me, I looking into one until this showed up 👍😁

I never thought of them lifting on these fender brackets and causing firewall damage. I bet it's a good possibility for this replacement cab though I originally thought it was from an accident. It sat inside a garage for over 20 years as a loose donor cab before I bought it. I fixed mine in a 'short' video. It wasn't too difficult, but it slowed me down at the time. Thanks for watching! Keep those old Fords alive! 👍😁

Awesome! Thanks for watching! 👍😁

No this project did not have any damage passed the rim joist and sill face. The studs were never exposed, maybe you are looking at the sheeting / loose tar paper on the wall. Thanks for watching and sharing! 👍😁

Which parts?

I hope so, I bought it quite a while ago with the plans to help with all of my projects. It's finally fine to start burning some metal. Thanks for watching my Friend! 👍😁

Thanks! I am glad my video was helpful. Sometimes I get a little too detailed on my explanations, but it looks like this one was helpful! I still use the same 520 to mow and snow plow. Great deal on the one you found..... Thanks for watching and sharing! 👍😁

This refrigerator was super sensitive to high humidity and didn't like high heat loads or too frequent door openings 🙄.....I fixed it; ie bought an LG on discount. The old one is at a single friend's house and it has been working well; No changes or repairs 1-1.5 years ago

Thanks Zane! I was seriously debating on leaving the old belt for a minute.... Thanks for watching my Friend! 👍😁

I do too! I've owned this one for almost 20 years now. Thanks for watching 👍😁

Thanks! 👍😁

Thanks! The amount of space for the belt swap challenged my sanity for a minute. Thanks for watching my Friend! 👍😁

Yes, I have a couple though I'm not sure if they were very helpful in my work on Johnny #5. Send me a direct message on FB, Instagram or Gmail and I can try to file share them with your email address..... They are too big to email directly. Thanks for watching 👍😁

Hi ANDY, I would like to see the unedited version of this video, with sound. LOL ‼️

@@rammanjr88 I used some pretty interesting commentary, may have threw a wrench or two, and muttered some new combined versions of the classic F-bomb . In particular it became an adjective, noun and verb all on its own. Thanks for watching my Friend! 👍😁

No this is the automotive version, I believe Fitech sells one, or a different manufacturer, but the only difference I could tell from the specifications was a more waterproof ECM. It was double the price with a blue ECM. Thanks for watching. 👍😁

It took me two 12-14 hour days to complete the build. Add in a couple extra hours on top for rubber mulch and anchor installation. Organization is key, lay out all the pieces in order for a more efficient build. I didn't do this until day 2. Thanks for watching 👍😁

Yes, organization is key in this project. I laid out all the components in order on day 2 and it was a huge time saver. To finish the area I installed rubber mulch around the playset. It looks nice and helps cushion falls. Thanks for watching. You'll become your kids hero 👍😁

Thanks! I'm glad you enjoyed the video. It's difficult to find the right balance to please the masses. Some enjoy the extended explanations and others complain I talk too much 🙄. Pressure washing before the new belt would be ideal....I think my pressure washer needed serviced when this video was taken. Thanks for watching and sharing! 👍😁

I think that is what they were trying to say, but it isn't correctly identified to me. 🙄 If you buy an electric motor it doesn't say 0-1125 rpm. It just says 1125 rpm. Thanks for watching and sharing 👍😁

I know. I’m with you. It was all sarcasm

Makes sense! Thanks for watching and sharing 👍😁

Good idea! I was worried about its clamping power on the sideways test. Thanks for watching! 👍😁