The slugs it makes would be good for patching other holes of its size, and yes I know a slower speed would be very helpful, As it is it gets the bit hot too quick.
That's why I was disappointed it didn't come as expected, but surprisingly it works pretty well at the higher speed. Time will tell how well the cutting edge holds up. Thanks for watching my Friend! 👍😁
If this was a regular gig I would have a Milwaukee branded unit. I have used them before and they are niceeeeee! Also out of my price range by a large margin. Thanks for watching my Friend! 👍😁
I'm impressed by the hole quality. No pushed out burrs on the backside and the hole is actually round. That bird nest of chips kind of scares me though, but it's hard to tell on video how close your hand is to it.
It impressed me as well.....I will give it a more thorough testing during the dump truck build. I don't think the shavings will cause too many issues. Thanks for watching! 👍😁
Sure would have saved me a lot of work installing snow plows and trailer hitches. I've been seeing more Vevor stuff being sent to RUclipsrs and wondering how it holds up before I buy something. Thanks for posting Andy.
I wasn't lucky enough to get this one for free. The magnet power is something that may limit its abilities, but I'll see how this guy holds up. I hope to use it on all the frame drilling for the dump truck and Margaret. Thanks for watching my Friend! 👍😁
on anything less than .250 in I always clamp a bit of .500 to the job and put the mag base on that. magnets require mass otherwise you run the risk of lift off
You just broke the cap seal because that oil tank is a repurposed bottle designed to be sold filled and sealed, but that's fine, a custom made oil tank would have been more expensive.
I think that is what they were trying to say, but it isn't correctly identified to me. 🙄 If you buy an electric motor it doesn't say 0-1125 rpm. It just says 1125 rpm. Thanks for watching and sharing 👍😁
The slugs it makes would be good for patching other holes of its size, and yes I know a slower speed would be very helpful, As it is it gets the bit hot too quick.
That's why I was disappointed it didn't come as expected, but surprisingly it works pretty well at the higher speed. Time will tell how well the cutting edge holds up. Thanks for watching my Friend! 👍😁
Cheap but effective Andy 😎👍Can't beat that! 🔧
If this was a regular gig I would have a Milwaukee branded unit. I have used them before and they are niceeeeee! Also out of my price range by a large margin. Thanks for watching my Friend! 👍😁
I'm impressed by the hole quality. No pushed out burrs on the backside and the hole is actually round. That bird nest of chips kind of scares me though, but it's hard to tell on video how close your hand is to it.
It impressed me as well.....I will give it a more thorough testing during the dump truck build. I don't think the shavings will cause too many issues. Thanks for watching! 👍😁
Sure would have saved me a lot of work installing snow plows and trailer hitches. I've been seeing more Vevor stuff being sent to RUclipsrs and wondering how it holds up before I buy something. Thanks for posting Andy.
I wasn't lucky enough to get this one for free. The magnet power is something that may limit its abilities, but I'll see how this guy holds up. I hope to use it on all the frame drilling for the dump truck and Margaret. Thanks for watching my Friend! 👍😁
on anything less than .250 in I always clamp a bit of .500 to the job and put the mag base on that. magnets require mass otherwise you run the risk of lift off
Good idea! I was worried about its clamping power on the sideways test. Thanks for watching! 👍😁
You just broke the cap seal because that oil tank is a repurposed bottle designed to be sold filled and sealed, but that's fine, a custom made oil tank would have been more expensive.
Makes sense! Thanks for watching and sharing 👍😁
Technically speaking it is variable speed 0-850. Turn it on, it goes 850 rpm. Turn it off, it goes zero rpm.
I think that is what they were trying to say, but it isn't correctly identified to me. 🙄 If you buy an electric motor it doesn't say 0-1125 rpm. It just says 1125 rpm. Thanks for watching and sharing 👍😁
I know. I’m with you. It was all sarcasm