Видео

The setup is great with the 3s lipo. However, if you gear up it will over heat easily so you should get the esc fan a motor heatsync. For adding lights, I do believe you have to change the transmitter.

Unfortunately I can't remember anymore. They are for 1/8 scale though since I did the 17mm hubs.

@@odrctrx754 no worries. Thanks for the reply

Are you using the correct velineon motor? If using another brand, sometimes the shaft is a bit shorter. Also, make sure the pinion is in the correct position with the gear at the outer part.

I got it! I took the back off like you did and didn’t realize that little screw that the motor hinges on the body plate was caked up with dirt. This mfr RIPS now lol, such a dramatic difference.

That is in fact the most important part of the video, as this can definitely be frustrating 😂

So you should definitely replace the center diff with a slipper clutch from a slash. The motor and esc combo can be the velineon I used for easy compatibility but you can go with a hobbywing brushless combo. If you're using a 3s battery at some point, you should definitely get a motor fan as well, specially if using high pinion gear.

Nice! Didn't know that

Every part of the axles are replaceable. Some parts are just harder to replace. I struggled with this one myself. Easiest way is to buy full halves of the axles instead of single pieces or the whole axle.

Oh ye I am sorry I forgot to tell you that it worked Tysm for helping me it worck s great I am subbed now and I Have used it twice

After the conversion you definitely can. That's why I bought the proline body mounts.

I know. It was the first time I ever took that apart and realized it after I did it. I was very new to the hobby. Sorry 🤷🏻‍♂️😂

I definitely recommend replacing the center diff with slash 4x4 slipper clutch setup along with the 32pitch gears. Center diff doesn't hold much power.

I believe it was in the 30s. I have a 19/54 now and it's in the high 50s. It has a slash body now so the aero is not good and when it reaches that speed it wheelies and flips

@@odrctrx754 30mph with 2s sounds good. If 19/54 flies it is uncontrollable. I have Titan 12 T brushed engine I'm going to change it this week to Velineon 3500 and I'm going to put 13/54 to run off-road and bashing

With the setup on this video amd a 3s battery, it goes up to the 30s mph

Same

It's very simple

Why would you be scared? It’s all part of the hobby.

Not sure if you guys gives a shit but if you are bored like me during the covid times then you can stream all the new series on Instaflixxer. Have been watching with my girlfriend recently =)

@Kyree Koa Yea, been watching on instaflixxer for years myself :)

Yes, the arms are the same.

I replaced spur with a slipper clutch amd 32 pitch 54t and pinion with 32 pitch 13t. That is the setup that comes with the slash lcg. I highly recommend replacing them.

You gotta change the gearing!

I used it for a few months and had small crack in the front and the spoiler holes suffered a bit. I had a few bad accidents and nothing terrible happened to the body.

This is me basically knowing nothing about rc cars 😕😂

@@odrctrx754... its all good u gotta start somewhere nice rally car tho .👍Go TRAXXAS.!!

It's bangarang from skrillex

It was great up until I converted it to a slah. I stiffened up the suspension just a bit after doing the hub conversion for on road wheels.

@@odrctrx754 But why converted to slash? Personal preference or something in particular?

The number is 6856X

Thanks man

Unfortunately no. I've been waiting for the traxxas one but still not out there. I'm gonna buy a garmin or something soon.

I just used a GPS phone app and put the phone inside the car body. With the 15T pinion and 54T spur I get 30 mph on the 7 cell NiMH (8.4v) battery. Using a 3 cell lipo (11.1v) I get 42 mph. Fun, but in less than two weeks, about 10 runs, the tires are shot.

icin4d I had mine at 38 40 on 2s and 60+ on 6s before it Caught flight I had to upgrade the slipper clutch to a slash 4 x 4

I'm currently using 54T spur and 19T pinion on 32pitch. Using 3s lipo that's about what I'm running.

I'm still pretty new to RC. I got my first slash about 3 weeks ago. I'm not sure how this setup is going to work out. Do you think I will need to change the clutch out? I am using a bigger motor by castle and a 4s lipo (If it works). I just watched a video where someone melted the stock clutch on 3s lipo. Also, I have a new slash 4x4 vxl slipper clutch left over. Will that fit? I know its way beefier than the one that comes on the rally ford fiesta

I would definitely use the slipper clutch. That's what I have on mine. I've seen people using the slipper clutch out of the rustle I believe it is when using a lot of power.

I think it was in the 30s with the 2s lipo battery.

@@odrctrx754 use 2s? Not 3s?

I did notice the arms were different but I don't know if I'll change them or not. I might get another chassis.

@@odrctrx754 I only noticed after getting some rpm arms. They are still not on as I would have to change all the linkages. It might not matter anyway since the truck body looks good on it.

Thanks man. I'm know I'll have lots of fun with it 💪

Thanks 😁

That's the camber arm. You can replace those with adjustable ones.

I can't wait to start working on it 😁

I cant wait to see you destroying it. haha just kidding.

😬😬😬

Rally's are awesome but I'm still waiting on traxxas gps module and I wanted to use it on the track. The slash is really good at the track. Someday the rally will be back 💪

yea i made my rally in to a monster rally with some 2.8 redcat valcano tires and that thang ramped every thing i just had slipper clutch problems

54T - 32 pitch

thanks, I have a 19T pinion and it over heated in 10 mins fast though but shot runs.

From the factory is a little slow but still a lot of fun

Fired Up Extreme RC thank you so much bud