Видео

Definetly exhaust manifold bark. Using cheap oil like quaker will make lifters caked up inside and, fail though.

I put Vaseline on the bottom and top of the shaft. All the hoses were clogged with crusty flakey mineral deposits. I cleared them up with a straw cleaner

Anyone have a recommendation for the gasket where the bottom of the auger rests? I had a deep clean with calcium buildup and cleaned so hard the gasket is leaking…

Watch this at 1.5X speed. You're welcome.

How did you get the Black part off? Mine is doing the same thing. I have taken it all apart but can’t figure out how to take the black park off to see if that’s the problem. Do you have to put the spray form back in side under the black casing?

Bottom line, these ice makers are crap. A $500+ appliance that requires lots of maintenance while it works and quits after 2 years. Call GE and they will tell you to clean it. Eventually flushing it with bleach/water solution and vinegar will no longer work. They will also tell you there is no product service available for these expensive ice makers. There are no replacement parts available. Bottom line, don’t buy this product. You can buy a lot of nugget ice from Sonic for $500 and keep it in your freezer without all the hassle of owning this piece of junk.

Would you fix ours if we brought it to you? We live in Huntsville

Nice swing! The follow through is real good.

I cannot get the worm gear out of mine. Any suggestions on how to get it out?

How hard of a job was it

If you don't have the tools a create your own drive shaft for the gear box, any other suggestions on how to make this repair?

Great pair of videos. I just tore mine down and saw my shaft is broken. Would you consider making one for me? I can't find the replacement anywhere.

Do you have trouble getting the ice bucket in it seems like it's in but it's not going all the way up I heard a piece of ice fall out

free hellcat supercharger

My machine makes ice but only a small amount and at a very slow rate. What do you think is wrong with it mechanically?

I have not taken mine apart but it seems to be the same problem. I also read comments and sounds like it’s not possible to order that part to replace it. I don’t have the ability to make my own piece like you did. Am I SOL? Do you think I’ll have to get a service guy out to fix it?

You wouldn’t consider making a shaft for a kfriend In Georgia would you? I have mine out buy do not have a means to produce the shaft. I was consider wielding the broken piece back.

How did you get the gear out of the unit. I have one that has done the same thing looks like getting the gear unit out is gonna be difficult.

I feel you on the year and half and it stop working. Well seems like I have the same problem. It starts out pumping then stops. I’m a women so it may take me a little longer to get what your saying

anybody find anything im havin this same issue

Trying to run cleaning cycle but nothing happens. Makes noise but won’t cycle the vinegar. Have done it many times before. Ridiculous that such an expensive thing should quit after 1.5 years

Thanks for sharing, ran distilled water and it still bricked, shame on GE and the Profile name

Could you order the part?

I have this icemaker, and when it gets hot in the summer, it quit making ice, because it becomes overheated, even though I have in front of a window, so if you’re buying it for the summer, if you don’t have an air conditioner in your home to keep this icemaker cool down. It’s not worth purchasing it for the price of this icemaker get a refrigerated instead, that has an year around icemaker.

Would you consider making these and mailing them out 😂

How did u make the cylinder square

How doe I get the auger out

Traveling by steamboat colorado we brokedown on my 2015 Tahoe the engine locked and till this point it will need new engine

I'm still pist off ab that

Hi! Mine is leaking from underneath the motor housing; is that also where yours was leaking from too??

Mines spinning, and it starts making a little bit of ice very slowly but then stops making ice and everything still stays white light.

my ice maker those not do ice it says add water and it has water

Hi first the spindle spin freely by hand? Mines seems locked up 🥹

Mine same symptoms so I checked the shaft. I attacked it from the top and once I took off the metal pass through with the holes I could see the upper gear the shaft turns. I manually turned it and it seems to be in connected because the little motor fan by the gear box spins when I manually spin the gear. Does that sound about right? I sat my leaf blower beside the condenser to blow more air and got one piece of ice out which makes me think I maybe low on refrigerant.

THE SAME THING IS HAPPENING TO MY SILVERADO! did you find out what it was ????????? Plz respond I can’t find the problem

Did your water move down the trough in the back?

Are it could be your timing belt tensioner broken on the inside.

2/17/23, My husband decided to tear mine apart to see why it will work maybe 10 to 15 seconds then shut off and/or start flashing "add water". Usually the tank is full. Now he's given up and told me to order the other ice maker I found when I stumbled across this one. I just want my ice back.

ৃ আ

Your video has helped me a lot! Mine makes grinding noises that come from that ice making section, did you put any lubricant in the bot of that shaft?

Incredibly helpful, thankyou

Soulmates over here😂 My Frigidaire countertop is pulled apart all over the kitchen. My teenage daughter despises my attempts. Thankyou so much, much better info than just “clean the inside “

Thank you, very useful video. Have you checked also the noise at the bottom of the engine? Was it more loud than behind the wheel?

Good video, I'm having the exact same issue, Can you explain to me how can i extract the screw that spins? mine machine this is stuck and I can get it out. Thanks

Do you no how to order that part that u created? I think that’s same thing wrong with mine

How do you get to the freezer section? I can’t get the styrofoam off. I cleaned out all the tubes (which were disgusting) but it’s still not working.

Where did you find the seal for the auger. I have one that pours water. I'm thinking maybe that's my Issue with my Opel Ice Maker. Would I need any other seal or gasket to install so It wouldn't leak. Thanks for this.

Thanks for the excellent explanation!

Hello. I have the exact same problem! However I am not near as smart enough to make a new part. Is there anywhere to buy one? I have been searching everywhere. I can find the drill but not the piece you made. Thank you for your video! Without your video I would have never known to look there!

You’re supposed to use distilled