Видео

I don't know why there is no mention of an output tone from the Signal Generator.... I know that the generator outputs a sine-wave because I can see it on the scale... but is there also a signal tone for a radio speaker that you can physically hear from a speaker ? I'm trying to do a shortwave radio alignment and I need to physically hear the 455Khz audio signal tone from the generator.

Hi, please is this scope good for serial decode? Thanks :)

Bought the DSO2D15 model, only months later I discovered it has Trigger Level problems with signals below 300 mVpp @ 1 KHz. I did all the firmware updates, still the traces run on the screen, no way to stop them. Things get worse if you keep the oscilloscope on for more than ten minutes. Then, if you select a 50 mVpp sine wave with the internal signal generator, the image is strongly noisy, distorted. I contacted Hantek several times, they wanted a video of mine showing the issue. Sent the video twice in a month, then Hantek disappeared. I re-sent a final e-mail today, I am waiting for a sign of life from them. At this moment no help at all, their after sale sucks. I did a BIG mistake, I should have bought a Tektronix instead but you only learn these things later...

Installing radiators on both IC inside is highly recommended

I’m hoping you can help me. I just got a Hantek DSO2D15. The trigger setting in 10X mode is not stable. I’m not sure if my scope is broke or if it’s a defect in the software. It seems to work fine in 1X mode. Set the scope in 10X mode. Connect the probe to a power source - I used the 5 volt probe check. Set the trigger or hit the Autoset button. Now adjust the volts per division a few times. Does your trigger setting drop down to 0? Thanks for your help and keep up the great videos.

Disappointment (very) with Hantek DSO2D10 scope . I own this unit (new) about 6 months and used for 2 months then it Ch2 became out of calibration - the zero is off by 150mV when use the "zero" button. The reading also lower than Ch#1 by about 46% when I connect the same probe to the square wave test output post of the scope. I used the calibration function(found in Utility bottom) and it came back with error code : 511d6. I also downloaded the latest software from Hantek. It did not improve and same error code. Tried email to Hantek service . Hantek in China finally responded with instruction to re-flash firmware.Followed instruction exactly and the results were WORST > now CH1 zero is off by 800mV and reading 4V on 5V. CH2 was as bad as before. !!! Contacted Hantek again and cannot help and was asked to contact seller ( the seller was Hantek Official Store) If you are thinking of buying this beware you are on your own for service and repair. It would be questionable at best on the logistic , honour and followup repair

Why are you only focusing on the obvious that we can see ourselves on websites and such? Where is the review of this product?

I bought one yesterday, it looks nice

I purchased my "Hantek 2D15" about 3 weeks ago and I LOVE it! I likewise purchased mine from AMAZON and caught it on a deal for $299, with another $18 off + free shipping. This is my first DSO, aside from the JYETech 138mini and DSO 150 I have built. I plan on putting it up against both of my EICO 460's , just for fun. Both (analog and digital) have their purposes and places for me. I do LOVE my EICO instruments! I have updated the firmware to "20210416.00" from the Hantek site. This has seemed to correct any "lock-up" issues I had when it first arrived. My advice. Leave your actual "firmware" alone, until Hantek releases an "official" firmware update. I also like the fact the "D" models have the AWG built in. No, it is NOT a Keysight OR a Tektronix, but it seems to work just fine for us electronic hobbyists.......I like it! To this point, I have NO bad things to report with my "2D15" and I am VERY happy I chose it. Best regards to all, Patrick

I ordered today

good afternoon, where did you buy it? is there a link?

Can this be used as a digital multimeter? If so how? I would like to check capacitor polarity but can't figure out how?

Интересный обзор.

How do you like it?Was better scope out there for same money?

Thanks alot Sir for sharing your knowledge with us! Regards from Germany.

IS IT PROFESIONALLY OK IN COMPUTER AND LAPTOP REPAIRING FEILD

Hi, friend! Could you try to connect the device to Windows 10 PC or laptop? I received few days ago my DS02D153 and I can't connect it to my Windows 10 laptop (the device do not recognized). All Hantek drivers and SW are installed.

Ho there! Would you suggest Hantek DSO2C10 , 100 Mhz , 2 channles ?

I have a very big problème with same scop with the last firmware. The midle of screen is disturbed and frequency is mesured is multiple by 2!

Arrived today Ordered Dec 30 2020 ... they put the stupid power adaptor on the screen side sitting against the screen. Used my own US power cord .. had to turn it on and off a few times it was stuck at the Hantek Logo but Seems to be working now .. and Yes was your review is why I bought it .. replacing my OLD CRT Scope ..

Aren't you concerned at how noisy and unstable the signal was on the scope?

how many probes are included in this model?

I measured DSO2D10 from the output of 74lvc1g14 tr-1.5nS, the bandwidth of the oscilloscope is 250 MHz. With a bandwidth of 100 MHz, the readings were a pulse rise time of 3.5 nS

Thanks a lot!

Thank you ! It's such a long wait to get it out of China, and such a mystery that it is not listed on Hantek's site, that your video is a balm on the "does this thing even exist ?" wound. On paper it has better specs than DSO5102P while being cheaper... but I started to be so disappointed by the wait and lake of information that I was about to cancel my order. Not only you prove it exists but you show how it looks neat, no obvious bugs (is this really a Hantek product ??? XD ) I guess you've just helped a bunch of people to find some patience.

I have the 100mhz version and it wont read any of my usb sticks, could you try yours and let me know if it works please.

Please post more reviews. Thanks

thank you!

Rectangular pulse generator up to 5 MHz?

Дякую!