Видео

Exactly all the shavings are in the suction line now.

Hey. When you’re swaging with a tool like that you should swag the upper pipe so any pieces of copper that inevitably come off will not fall into the pipe. Hopefully you don’t cause a restriction.

Very nice. Hi, my york YP9C inducer motor has only two wires. How is it able to ramp up and down with only two wires connected. One wire is HOT and the other is NEUTRAL. Thanks.

May I contact you? I have Hard Lockout Code 19 for my ALP105B

Those are just bad compressors have changed two on same unit. They are China made. Everything runs perfect only lasted a year. Can’t find any issues with air handler or txv

its not normal for compressors to just fail, something must have went wrong when it was installed such as not pulling a vacuum long enough

Has the refrigerant messed up your vacuum gauge?

Any idea what caused the compressor to fail, and what kind of warranty does the replacement compressor have?

Was this unit on LP? Maybe it was not converted properly?

Tare that junk out

Is that a 3 phase DC compressor?

Dude , I would had swage the other end. Now you got shavings in the liquid line to the metering valve😅 since it was r22 you might be saved

non brazed joints? i feel like thise are more likely to leak than a properly brazed joint

The pansy keyboard supertechs are out in force on this one. Nitrogen was not used 30 years ago and still the units will outlast new versions.

Easy money‼️🎯

Any time I install American standard or Trane I like to remove that side panel to verify that none of the pipes are touching anything. Especially the ones that go under the coil to the compressor. I like that RLS setup.

did you like it when he bought the nitrogen out after he brazed ?

What torch did you use for brazing the line? Is it a red color tank?

Cat got your tongue?😮

dumping out those fitting like my kid does his Lego's lmfao, good job though dude!

Anyone else get anxiety when he was cutting the line with them shit rigid tube cutters 😂

What size torch tip do you prefer?

Can a 3.5 ton unit be reduced down from a 7/8 line to 3/4 suction line? The old unit is 3 ton with 3/8 and 3/4 lines.

If you are a DIY homeowner, I suggest to install the overflow bypass. Just look at how to from the manual.

Bad sensor or wasn’t hooked up

Btw those blow out guns are the bane of my existence.

She plugged, lucky someone isn’t dead

How much will you be paid for this cleaning?

Hello I am from Turkmenistan My name is Bayram How much do they give you for this air conditioner cleaning?

Wow a tape warrior huh and shot a screw almost into the coil looks like some service men would try to do I do not keep any of that shit unless it a complete new install and it’s code, my metal work don’t need tape because my shit don’t leak

Nice work.

4y55tttttttt

There's a spray can product at the big orange box store that you spray on the coils (let it sit on about 10 min.) and hose off, in case you don't want to use the on-hose cleaner. I did mine without even taking the case off...much better!

Looking to buy the yellow adapter . Did you pushed it with something??? What you called it please. Any link ?

I have to ask why you cut the damn coil out to replace a compressor??? I have done many of those a never had to cut the coil out. Invest in the NAVAC for swage tool. Worth every penny.

I stoled your music and I'm moving to Nashville!

WOW!

Never seen one that dirty.

What kind of sprayer are you using?

1000 dollars for capacitor and coil cleaning, Say its not so?

Wow... Now that it's clean...customer should have a lower light bill..now that compressor isn't working so hard...awesome job

Probably should start showing you turn off the power lol.

Heard the song and knew he knew what he was doing😂😂😂

Careful with that nu-brite on that grass, they’re gonna be pissed when it’s all dead

Yes sir that'll be 500 buckaroos cuz gonna be cold cold now

Spine fin coils are water only. Nu-brite is way too strong.

👍🤙🤘😮

Glad you didn't step off the ledge, looks bit DANGEROUS

Good old carrier heat exchangers, they keep us busy

And they hate hard low volt wires, they want it to be shielded stranded wire