Видео

Thank you

awesome mate, think you just found by problem.

Man… had mine rebuild and still have that noise this eases the mind..the mechanic don’t even know why it have that sound

and thank you for this video, i also have a bit of relief knowing it may be this simple of a problem i am having

so a question, once you tightened the nut, and did nothing with the bearing that also made a clacking, did the noise go away ? since the clacking could be coming from two points and one was remedied ? just wondering because the second point of noise you did not do anything to.....wondering if there is something that should be done there and what , if possible to fix ....

My 04 300 exc only makes that noise at high rpm

I have the same clacking sound on my 2 stroke Yamaha DT air cooled engine. I already rebored the block, changed the piston, piston ring and "piston pin bearing" all brand new. The connecting rod is okay because it has NO up and down movement. The clacking sound becomes obvious during engine idle only. The noise is coming from the engine block. I just could not figure it out. I will try to change the "piston pin" as a last resort. Any clue or suggestions?

Sounds ghetto but shim it up with a washer. Then tension the spring on the power valve flap.

Can you pop the ball joint off and thread it down one full turn to add a little bit of tension?

Did it minimize the sound when the clutch was engaged? Mine makes a rattle sound when idling and when the clutch is engaged it goes away

Mine sounds the exact same as if there was a piece of card between my spokes but it’s from the engine and only sometimes while I’m riding and I h e no idea what it is

My 2 stoke four wheeler makes noise exactly like the noise you were making (very bad when rpms are decreasing btw) when wiggling inside the power valve, but there is no power valve on my four wheeler, HELP!!!

I go camping here twice a year. Love the place! Always looking forward to going there!

Mine sounds like a bald eagle in a blender. Thanks for the info this helps.

Best vid from Kowen 17 so far, captured the event well, the best single track I ever rode. I was the guy riding the 2013 six days 250 2 stroke in your vid. Rode the west loop Sunday and realized I should have rode it Saturday.........damn rain...

mine sounds like a grinding table saw?

heading there this weekend, last time was ten years ago

When is the next gutbuster at Rydal

what was the result after this vid? mines been doing the same and has got much worse this last few weeks

my 2013 ktm 300 is the same had top end done and now the pv is rattling but its doing it on idle and all through the revs and sounds like it's getting worse I thought it was the bottom end or something like that as well until I seen this video pulled the pv cover off and has the same kind of movement is there any way to fix this because it doesn't sound very nice??

I think u have set my mind at ease mine does the same every now and then usually when I'm putting along in first gear barely giving it gas it is literally the same noise

That explains so much my 2007 200xc does that at idle

Power valve looks a lot more complicated than that on my yz but then I guess it's adjustable in a way mine isn't.

Just did a top end on my 2000 300exc and mine is noisy when you down shift and its anouying as hell but its not hitting rings or piston . I didnt have the keeper clip in rite at first but realized my mistake and its a little quieter . Guess its common on these bikes but i have 24 and none of the other makes have that much play in the system. Almost want to shim each side without binding it up so it doesnt stick.

lower rod/crank bearing. same thing that went in my kawi. thought it was around their on my engine.... she needs a FULL rebuild. ah, was wishing to hear it run... im not sure now, it could be the PV

Hey guys this is Paolo aka the 'THE BIGGEST MAN EVER!!' it was a great event and i'll see you there this Saturday to do it all over again

You need to clearance your power valve an new seals for it

the my ktm 250 exc 2002 have same noise,how can i stop the noise?

nice work Trentino. looks like i could learn an editing tip or two. have you got my email? Check out the casarpark page on face book - it's a social enterprise project I'm working on and I'm struggling through the creative process of creating a crowdfunding video to promote it...?!?!?!

Brilliant thanks

Yea, just ask the cabin attendants and they will get them for you when you get on.

Are those the cots supplied by the ship?

I didn't do anything to fix it. The only thing that I can think of is that when the top end is done most people clean out the power valve and then it has tolerance to move as its not filled with oil etc, so it rattles on idle. Been riding it heaps, no problem at all..

so slow

great video. love it

nice single track - like in the mountains of Montana.

fucken love wattagans

way too much dash..

This one is in NSW and is on public property so you need a registered bike and a licence.

do you need a license to do one of these rallys?

Enjoyed your family vid to camp cobark.. very nice spot..They captured malcolm naden not far away from there!!! But, when u ride.. u need to blink sometimes! and 2 ... go grandma!!! great baby distractor

sorry if its a noob question but is the first bike a 125?

Nice one...never ridden up there before tracks look good Rickster

nice one mate

Cheers Thanks for taking the time..

Classic, top job there bloke.

Laughed my arse off mate, great production :D

@anthonyparisotto Thanks mate, still need to to get an HD camera I think. The quality that you lose when you upload to YT is noticable on the non HD variety. Your vids are so much clearer.

nice one mate

Just Great!