Видео

Hi Laura, By reducing it to 1 seat doesn't affect the air bags as it would be the same as 1 person sitting on the bench seat, the air bags are in the dashboard not the seat itself.

I used 25mm on the floor and 50mm for the ceiling.

No I had to make it, it took a few attempts as it's a really awkward shape. I made several smaller ones out of thin scrap ply for each section and taped them together before making the full size one.

@@timnolan-dacre8579 okay that’s interesting! I’ve got a Renault master but not the extra high roof version and have been wondering how to finish up to the cabin! So that’s super helpful thanks

With 3 mm vinyl ply from morland UK. Pre drilled and screwed in to the ribs of the ceiling, just don't tighten too much.

@@timnolan-dacre8579 have you got any pictures? Did you do just the middle or bent it to do the sides?

Hi Steve, yes it's the taller of the roof heights and made of plastic, I fitted a Maxxair skymaxx to the rear, it fits a 40cm x 40cm opening and to the front I fitted the Maxxair maxxfan, I'll put links to them below. www.rainbow-conversions.co.uk/rooflights-vents/maxxair-skymaxx-rooflight-vent-400-x-400mm.html www.rainbow-conversions.co.uk/rooflights-vents/maxxair-maxxfan-deluxe-roof-vent-fan-with-remote-control-353-x-353mm.html

It was like that, Is your van a FWD or RWD? Mine is a RWD, I'm not 100% sure but I think the RWD vans have a higher floor to accommodate the prop shaft.

Its a mastic sealing strip, use it to fill the gaps then a strip all the way round on the top so that the skylight has something to bed into, the camera battery ran out before I finished, once the skylight was in place I trimmed any exces mastic tape then went round the whole edge with sikaflex. Because the ridges are so deep I went through a roll and a half on each skylight. Hope this helps. www.ebay.co.uk/itm/351565459521

@@timnolan-dacre8579 brilliant thanks for that. Hope the builds going well for you. And lock down does t last long so you can get out and enjoy it.

Just pre drilled and countersunk using normal wood screws, just don't tighten them too much. I also stuffed some more insulation behind them too. The phone battery had died before I had a chance to film that bit.

@@timnolan-dacre8579 cheers thanks for the help

Thanks for the comment, do you have the high plastic roof too?

@@timnolan-dacre8579 yes yours is the only other one iv see and is giving me a little head ache with how to cover the inside of it lol

We've covered ours in 4 way stretch carpet, I've uploaded the video this morning. Because of the shape of the Master we decided to put the vapour barrier in front of the plywood rather than behind because there was no way we could have fitted the plywood without ripping the foil bubblewrap, (far too much of a curve).

Just realised you probably meant the ceiling, we've used 3mm ceiling board from Morland uk, we're fitting it at the moment. www.morlanduk.com/vinyl-faced-3mm-plywood

Thanks, the skeleton stickers are sheets of butyl, they add mass to the panel so that you don't get a tinny rattling sound whilst driving.www.ebay.co.uk/itm/282119695808

When I cut out the floor covering for the fourth bolt hole there was a domed shaped bolt already in it that would need a special tool to remove it, I filed 2 edges of it sothelat I could get a spanner/wrench on to it, I tried to show it in the video but the camera wouldn't focus on it properly for some reason. Apart from that it was straight forward.

@@timnolan-dacre8579 thanks for replying Tim. is the single seat a Renault product? did you buy it it new or second hand? and approx how much?

www.ebay.co.uk/itm/363090592924 That's a link to the ebay listing, I offered £240 which was accepted, not the cheapest of items to buy 😲

Paul Very easy done have done it on my x62 you will find second hand seats on ebay and gumtree they are cheaper there is a guy in Melbourne he charges 850.00 others are around 50p to 600 let Me know if I can help you further

@@fpv49 thank you. Yes I found the guy in Melbourne $850. The swivel was from another source was 3 or 4 months away from overseas so I’m looking for a local/ in Australia supplier. Any ideas?

Is it a Renault Master you have? The tensioner for the middle seat is enclosed within the bench seat so I didn't have to do anything to it, also there were no electrical connection so I didn't have to adjust anything with that either.

I've done the first fix wiring, insulation and boarded with ply and currently carpeting the walls, I need to edit and post a couple of videos just not got round to it yet, I'll try to put some more up this week.

There's not many L4 H3 Masters about, do you have one yourself?

Yes I filled it with black sikaflex, I also ran a bead around the whole of the outer edge of the window too, didn't fancy the thought of water sitting in the curves of the bonding if that makes sense.

Awesome, thanks for your help 👍

Great videos. Hopefully there will be more as I'v just brought one of these Van's to convert myself. Thanks and keep them coming please.