Видео

Looks are everything 😍

Thanks for showing that the SCS CAN be installed using mil-spec retainer pin.

Thx 10-18-2024

Does this ricochet more than other dueling trees?

What about a video about this Comp and performance of it

Man your rifle is so clean I usually that not shoot it.

Excellent video.

Where do i buy the vice block for the ar15???????

Who makes that dueing tree?

Look up ABRAMSMFGM1POST BEST IN THE INDUSTRY

What bracket kit did you use for the EMT pipes?

Did youtube edit your video?

Looks like you have that 3 legger backwards dude. That 3rd leg (lol ) should support the energy from the impact. The way you have it here, the 3rd leg is more of a counterweight as opposed to an outrigger my nigga

Tired of just shooting silhouettes at the range and looking to add some fun with steel. This vid is a great review of the different mounts! Mahalo🤙

Why dont you show us how you reload and chamber a round after mounting that scope right under the chamber handle !

501st P.I.R. Hooah ! 🇺🇸

Your method of testing is using the garage in a way it was not intended to be used. Why not try pullng triggers with it?

Keep all your mags loaded, Empty mags are like dead power tool batteries, Useless when you need them.

Thank you for your Great explanations. I have some rifles, I'm not a builder, and the tip, about not to check with a live round, and the reasons why, definitely explained why the right tool for the job is important, YOU'RE life could depend on it, Again, Thanks. Ted R

The 2X4 tripod should have the bottom stick at the back to resist the force and avoid shrapnel.

Very well done! This is the only video I've seen of the complete swap out. I like the way you install the pins. New subscriber here.

Great video 👍🏽

You should use red loctite at the minimum or better yet Rocksett on the set screws..The screws will shoot loose if you put any amount of rounds through it.. 25 inch pounds is more than enough torque for the set screws..

By using light sandpaper, you can lightly knock off a few thousandths of an inch of the flat side of the crush washer until you reach the final quarter turn at hand tight. Then tighten to zero with a wrench. This will prevent damage anywhere along the barrel. This is how I do it and how I will always do it.

Wonderful job! bro 👏 thank you very much !!!

Did it go out of spec again?

I’m trying to learn on how to find something for suppressed application and what works best for

This system will not outlast or out-perform a spring buffer.

So no need for Rockset when using a crush washer?

Any advice for my situation here.. my punch slipped off that depressed pin and now the pin is stuck in one of the grooves on the scs system. I cannot access the pin to depress it or move the buffer at all..

Thanks brother

Does this change harmonics

Did you remove the ejector and extractor?

awesome review Mate, like the clever way you use with the selector pins, very good technique well done Mate.

cool

Did you tighten the set screws in the bottom of the drop in?

Nice JOB .

By "release", do you mean reset?

Bravo 👏 You are the 1st person I have seen not cutting corners and adding some Loctite on the pins. I have no clue why so many people are skipping the simplest, yet very necessary step. Add some thread locker people! It doesn't hurt and it keeps things where they're supposed to be.

Newbie AR owner here, thank you so much! Struggled putting the new charging handle back in but after a few minutes of trying to align the wings with the grooves, I figured it out. 🤦‍♀️

Thanks neckbone!

Do they make something like this that has a muzzle brake combo shroud?

This is excellent! Setting up a range in the Nevada desert.

I never have checked head space before but I’m getting more experienced in building so I probably will order the tools to start checking all of my headspace’s

Tighten, loosen, tighten, loosen, tighten until you’re about a quarter to half turn

Thank you, that helps a ton!

GPS SAYS on the packaging that it doesn't matter if your right-handed or left-handed

Imthink THE LYMAN IS BEST mechanical gauge since it is the same concept as Wheeler, the measure point is on inside of gauge, except LYMAN(Orange) is metal & WHEELER(Black&Yellow) is plastic WHEREAS the GPS(Green) & BIRCHWOOD CASEY(Red) are identical using that clear ring on outside which could easily break if it was dropped or anything hits it on the outside just seems like a bad design especially for something like this!

Thanks for the detailed video! earned a sub

Love my R 140. Gives my gun a new better personality.