Видео

Hi Paul! Thank you. It works pretty good. Weve done it many different ways. We are doin good. It hasnt been really cold yet. Merry Christmas to you and yours!!

I have a video of putting wheel chair motor on it. Takes a little but i got it. Thanks for stoppin by and commenting!

And your controller will work the variable speed then and get limited switches on each side of your mill to shut it off at the end of the track! I'm working on mine too , I'm also putting a safety kill switch on it for emergency shut down , good luck I hope I've helped I'm learning a lot too! Lol. Take care my brother Robert Alabama

@roberttidmore647 i didnt put limit switches on it. I had to add another battery for the 24V wheelchair system. Fabbed a bracket to hold both motors b/c the computer wont run unless both motors were plugged in.

Didnt get around it. I havent used it so not sure if it would be an issue. I will take your word that it is. I did put some fuel in it after i got it set up and come to think of it it may still be in there. I will keep it in mind if i do fill it and make sure to put a check vent in it. Thanks for the comment.

Glad you were able to get it dialed in. They can be a pain. The fuel line is another thing ya have to be aware of when putting the filter on. It can loop up and get pinched. Theyre good saws when theyre dialed in though.

Hmmm.... wheres ur screws set at?

All the way in. Then 1 and a half out

Thats pretty rich. I usually start at about 1 to 1⅛ out. Will it start at all?

Youre welcome!

The guide bar has 2 nuts on the clutch cover (rh side). I believe they are ½in or 13mm. Also need a flat screw driver to tension/loosen the chain. Is that the bar you are asking about?

@@307j.o.a.t9 thank you so much! I am just removing my brake handle, but I am still learning about identify certain tools. Trying to educate myself, lol! I was stumped on what you used to unscrew and remove the actual handle itself! I’ll have to get those tools and remove the handle! Thank you so much for your help!

I would have to check on the saw to verify but im sure the screw on the brale handle is a 4mm allen. There is a tool called a skwrench that is used for bar nuts, spark plug and flat head screw driver on the end. Is your chain brake handle broke?

Awesome! Glad it got ya out of a bind. You will have to find whats causing it to blow if ya havent already. Mine was the vacuum pump. Thanks for commenting!!

@@307j.o.a.t9 the overdrive switch popped off the shifter and the wires shorted. Strange thing to happen. Thanks again and I like the way you test fuses. Much faster than pulling them out and looking at them .

Oh that will do it. Thanks.... yea it sucks to pull fuses.

I dont remember exactly. Id have to go back and watch the video.

No problem! Glad it came in handy!

I think its definently worth the money. Square ground chain is so much better falling and in clean environments and the square jig is an economical way to keep it sharp. I plan on doing some more vids on it. All the people i know that use it think it works well.

Its definently nice to have. It was a little more than i was planning on when i bought it. Needed to research a bit more but it all worked out and now we have plenty of hot water. I think they should make lp ones for campers! Thanks for commenting!

It was awesome up there!

Lol... yea she runs. Thanks.

Lol yea! We are foin good. Lookin foreward to our trip to Washington in 6 days. How are ya all doin?

@@307j.o.a.t9 about tge same buddy. Hope you have a great trip. Be safe brother

Hi Paul! Thanks. Theyre not too hard to rebuild. Hope alls well with you and yours.

Thanks! Yea we will be on our way in a week!

Nice! Yea it will be a good saw for Paula. Needs a muffler mod and maybe a little shaved off the exhaust. I might have that 2150... he gave me a built 2150.

Good idea! Thanks for the advice! Appreciate it!

Yea stupid way to do it for sure!

No its a diesel motor.

Thanls buddy. Good to hear from ya! Hope alls well!

@@307j.o.a.t9 Hey Travis yea all is good here same old thing just chasing that welding work.

Thats good.

Been a few years since ive worked on that. No theres no outer seal. The grease in the bearing amd the inner seal is supposed to keep the gear oil sealed in the diff. I used silicone sealant when i bolted the axle to the tube. I also drilled amd threaded a grease zerk so i could add grease between the inner seal and bearing race after installing the axle. Thanks for commenting. Hope it helps.

Lol thats alright. I read them anywhere ya put them.

Good to see ya Paul! If pushing wprls keep it up lol. Thats cool you got to mill the jambs.. Thanks for all the support! STAY SAFE!!

No my wife bought it before we met. It was built in the 80s. We had a great weekend. Thanks for asking. Hope yours was good. Appreciate your support. STAY SAFE!!

Like to see the mill running again, be nice to see you again at Taz’s

Yea i enjoy running it. I cant wait to be at tazapalooza amd see you too!

Idk of id say one is better than another. I have both and have good and bad experiences with both. Def not a fan of the 450 and 455 xtorqs but theyre not a pro saw either. I have an ms 261 that give me nothing but issues but have an ms 361 amd 2 660s that are great saws. Thanks for stoppin by and commenting!! STAY SAFE!!

We are doing good. Dang the words out? Lol. Yea it should be fun today.

Its awesome!! Yea being challenged is what makes us learn. Thank you for trying! Its awesome!!

Love ya too!!

Love ya too brother!!

Thank you. Good luck!!

If i remember right it burned for over a half an hour.

@307j.o.a.t9 Those are interesting vids. Good visualization on how a chimmey fire gets outs of controll.

@@gratefulacres69 thank you. Yea its scary.

Oh awesome!! Thank you!

Wow.... 2nd one. Thats a lot of lumber to wear out an LT15. Thats awesome! Yea I definently wasn't happy with the rope system. i have a new(er) video adding wheelchair motors to the mill to drive it. Im currently out of logs but hopefully I will get a bunch stockpiled this summer. I'm not sure I could push the mill through most of what I cut. Even with a new blade it struggles to cut some of the logs I put on it. Have to go pretty slow. Thanks for commenting. I missed it and haven't been watching lately. STAY SAFE!!

Yea not a very good option.

Western. South of Jackson 100 mi.

Most recently I lived in Wheatland and before that Lyman! Back in Arizona trying to escape!

Oh cool. Weather is a lot nicer there!!

Oh awesome! When i put the winch on somebody mentioned in the comments to do this.

I got the idea from a youtube video on a gokart build that needed a reverse gear. Cheap 12v winches like lego blocks; there are no limits to what you can do with them.@@307j.o.a.t9

If you cam get controllers to regulate speed. That was my issue with the atv winch i used. Couldnt find a pentionmeter that would last.

Thanks!

Thank you!

Thanks!!

Thanks!!

My son does yes. Hes gotten pretty good at it. Its a big sport npw.

@@307j.o.a.t9 Yikes!! Hopefully he is hooked to something...

Thank you. It was a fun project.

Thanks!

Good to know! I didnt even think about looking for something like that. I was trying to finish without buying more stuff and needed to get it done without waiting for more parts. I will definently keep that in mind though in case this system fails in some way. STAY SAFE!!

@307j.o.a.t9 yeah I even bought the mikron setworks for mine..

@@geraldminko4659 oh nice!!

Thanks! I will get a little millimg done soon. It was a fun project! STAY SAFE!!