Видео

Nice work! Can you detail the panel setup wattage for the two roofs? You have 6,960 watts total available by the stickers. If you have 4,785 watts on one set and only 2,175 watts on the other set, are they wired the same or different volts/amps? It looks like a very robust system and should provide a lot of power.

I like Hager and they also have rectangular knockouts. They have a rectangular plastic insert with 20mm knockout so an earthed banjo to earth the armoured should work. Otherwise drill the metal box but hate that as wears me hole saws out ! 🤣

Good work. I like to stick bonding or tile adhesive around as don't trust my sockets to stay fixed ..fixed ! 😅 i take it the bathroom light was a non connected or loose earth.

Just the vid I was looking for. IR test at a socket on a ring. Nifty technique.

I would have us hospital conduit saddles , not plumbers copper pipe clip. Also the T box at the socket one screw through the centre would have been plenty . Otherwise it a nice lean in stall 👍

What is the black flex or data cable going into the bottom of EV fuseboard and how do you connect it both ends should you not have showed us that

So when you said you’d show us, you just pointed at it.

No pig tail on the cable going back in through the wall and sloping downwards 🫣. School boy error or Friday afternoon install?

With no anti thedt protection from dirty thiefs rolling up and charging thier cars too better re think youre design with a lock system!

Great video 👏

Can you add an electric shower circuit on a garage consumer unit

Exellent

I smell plastic burning in my bathroom..

❤where do you get the power from.

Man United in one room

Why the speed up, no instructions and most missing, cant see what you are doing

Can i install a a cable outdoor extension to a pluged socket insidde my kitchen

In a shed / garden office does the consumer unit have to be a minimum distance from the floor?

Squeeze the croc clips a little…….the reading may come down 👍

L/L: 0.33. N/N: 0.33. E/E: 0.63. The CPC should actually be 0.55 with a tolerance of 0.05 ohms. So the max reading for CPC is 0.60. At 0.63 it’s technically a fail. Slight loose connection somewhere

Its actually within 0.05……..not 0.5, but that might have been a slip of the tongue

Personally I'd have routed the tails into the bottom right of the board to keep them clear of the circuit wiring, but good job all the same!

That’s a DB upgrade 😂 poor Tennant 18th Edition 😢😢😢😢😢NO RCD Protection

Great video. 250V should be ok for old wiring.

Good work, who fitted the Isolation Switch?

Did you install surge protection on this install?

so where is the Consumer unit change and some additional down-lights Video.

You haven't quite grasped the concept of shorts, have you?

👍👍👍👍👍

Well done 👍

Hi mate, great video for trainees like myself. Thanks for taking the effort to film, edit & upload. Very newbie question here, but when you buy the 3core cable does it matter what the core colours are? Obviously you use brown for live but why is it black for CPC & grey for neutral? Can’t you ask for blue, brown & earth? 3phase has black grey brown and it’s confusing me! Cheers 👍🏻

Good job

Can you explain to me why there are 3 red 2.5 wires in 2 of the 32 Amp Rings? Are 2 of them for a Ring and the 3rd a fused spur maybe??? Answers Below Please .

Russia 🇷🇺

Who pulled that main fuse out?

Nice little job 👍👊

Nice video. Are you keeping the ring intact due to carpets etc being up and would you in another environment if the carpets were all down & the room packed just fuse spur the ring and your sockets that way.

If you enjoyed this video don't forget to Like and Sub!

Does the equipotential bonding on the gas have to be before the tee on the gas outlet pipe? I know nothing about electrical requirements. Not sure how much of a difference it would make on this installation? As a gas engineer, just wondering how much of a difference it would make here? Nice tidy work on the consumer unit.

Did you have to change the wall box to deeper depth for switch.thanks

What size armoured cable did you use?

No gasget or sealer on angle box ?

Good job brother, love those lewden boards.👍👍👍👍👍👍👍

Good job brother great vid, I’ll catch up and follow your content. Hopefully I’ll get some content if my own out soon.👍👍👍👍👍👍

My mentor said if it is old wiring like you have in that property, then you shouldn't really need to test at 500v. 240v should be enough. Each to their own I guess.

Hi As there is no rcd protected circuits or spd in place. What code would this be now with the new amendment in force? Many thanks

Nice run through. Was the water supply a metal service ? The gas bond probably should have been before any branches.

Quality install. I'm still a learner in the trade so I find these type of videos very helpful.

Why earth twice this is 3 core armoured

Good tip.