Видео

Bro you just saved me money! Thank you! 💯

Love to see the after effect of what has happened now 3 years later.

Lower your idle control valve just adjust it

the line you used is the return line was kinda LOL while watching but anyhow, I'm a pensioned fleet Mechanic from FEDEX but as most know they only use Ford E-350 vans. So I'm not all that Familiar with GM vehicles did you find the pressure line from the trans to the oil cooler in the radiator? might've been located near the bottom of the radiator, also I made my own transfluid flushing tool when I saw how much Snap-on wanted for theirs not difficult to make used a 120V plug in water heating coil to heat up the fluid to 193 degrees Farenheight or whatever temp thermostat your car uses. then using a 5 gallon bucket fill to capasity of trans oil including torque converter for your vehicle with new fluid heat it up to operating temp & using a electric 0.5 gpm pump, pump it into the return line. while using using a hose to catch old fluid pressure line from transmission to a 5 gallon catch bucket, Raise the drive tires off the ground put the car in drive at idle the trans pump will pump out the old just watch the catch mucket for color change then turn off car & finish pumping new in with the .5 gpm electric pump this way the trans pump is never running dry and a complete flush is completed PDQ.

Once tapped do you need a reducer for you new lines or does the thread pitch the same as the new hose lines I made

If they take the hinges off pry it open that little center thing isn't going to stop the door from coming off.

You're a life (and knuckle) saver.

Thanks

Thanks for posting! I was getting ready to call a plumber and thought I would check with RUclips first. You saved me $$$ Bought the same one at Home Depot and installed in minutes. I owe you one... ;)

This is supposed to be a how to video to SHOW people how it's done not just say I removed this or that

Have a FH430V on a 48 lesco. I cant for the life of me get the cable/throttle adjustment to get high rpms.

Did 5 coats with a roller. First time ever still streaks. What a nightmare.

This is a common issue and happened to me aswell. Just proves never think someone is competent until proven otherwise, check your purchase before you leave the store.

fighting with this assembly right now. was going to leave everything loose but I decided to follow the directions and that was a mistake. I got the 40" and it's got a little different parts but basically the same

This thing had me pissed off. One illustration with the whole shaft with the spacers would have sufficed. I already hate this thing and its been too dry to use it since I put it together.

Those look like a pair of old Cutco shears. The best I've ever owned.

Thanks

took a screenshot of the vacuum breaker kit, went to HD, cost me $3.39 and 5 minutes time. all fixed

Hey thank you very much sir. worked perfectly.

What is the name of blue valve?

When I shut my car off, the belt kept running until I disconnected my battery. Now my car won't start. Do both the issues have to do with one another or are they two separate problems? Ant advice would be greatly appreciated, I have no idea about cars...

That’s for showing us nothing

This is great!!!’ My husband, landscaper and fence guy told me I could t install pine 4x4 without them rotting. I needed Home Depot to cut my 4x4’s so I didn’t have to buy a new circular saw this week. Home Depot would t cut pressure treated posts. So I bought the pine and thought about how to keep them From rotting. I went over to the driveway sealer/ asphalt sealer area and found all different kinds of sealers. Gorilla has a clear, white and black, but I decided, nah I want real asphalt sealer. I bought a bucket of it and then I came home to see if anyone else had the same idea and here we are. I think it’s genius and will probably last longer than pressure treated posts. I just had my backyard fence pulled down and replaced with vinyl and most every old post they were pulling out, snapped off a little lower than ground level and the fence was only 10 years old. So next week I build my own front yard split rail fence and I feel Very confident about my lots lasting a long time once I install all of them. I’m glad you posted this, so I can share it with others that laughed at me for the same idea

New office? Get a voltage detector.

Nice!

what if i'm having the same issues but not all the time only sometimes but everyday pretty much, after a while of driving it starts doing that, throttle body had alot of built up oil on it

I agree. Instructions suck. Built mine yesterday. Took way longer then it should.

Thanks for this. I'm assembling mine now as we speak, and the shaft directions had me cussing lol. I opted for Lowes to assemble it for it, but after a week they didn't touch my order...and now I know why.

2 long filler-knife blades slid into the gaps top and bottom and then pushed sideways and slightly outwards at the same time will easily pop those bolts open in seconds ;)

Thank you for the short video! One of our work trucks had a right side low beam not working and we fixed it quick thank to this video.

Did u say 2k rpm idling I'm at 650/600 rpm

dude. thank you

Didn’t actually show anything helpful

If you connect the rubber return line to a fluid bag and hang it, you will flush the torque converter as well and not risk runing the pump dry.

WNZ Differential Fluid Pump for Automotive Applications - Efficient Oil Extractor Pump for Fluid Extraction (230CC) a.co/d/2w5QRbc

Install a long hose in the drain hole dummy, then you can just drain it into a jug

Love too see what people come up with solving problems..cool idea

Problem solved...Thanks

I've been looking for a video on fords "quick connect" for hours, for my 2016 f150 heater hose. Thanks!

I realize this is an older video, but you are spot on with the written instructions. The instructions are pretty good up until you start assembling the shaft and how it all is supposed to go together. Looks like two totally different people wrote different sections of the manual and never collaborated with each other. If it wasn't for the actual company video, not so sure I would have ever gotten mine assembled correctly. Actually I still don't know for sure...but it is together and looks correct now... Oh and I have some hardware left over too! Go figure...

If you need to convert your file type this is s free tool to download obsproject.com/

The video didn't say if it fixed the problem, yes I read the comment reply that said it but the video should have. Otherwise good vid.

Great idea, looks fantastic. It definitely can be easily defeated though. I'm not going to go into specifics on a public forum. I'd definitely add another type of lock... Thank you for sharing your videos 🙏

Anyone live anywhere near oklahoma?

Hey bro I know this video old but where can I find the white top coils for 2005 .......can I interchange 2005 for the 2000 coil

Not in focus

Everyone knows about back rolling. And every painter knows to roll in the direction of the light. Are you new to painting? In many cases on commercial jobs, only primer is sprayed, not top costs. Spraying is more costly because it uses a lot of paint.