Видео

Thank you so much man. Your video just saved us at work after the hurricane that hit.

Best video about this winch. Thanks. Reposition the camera. Your arm is in the way. A lot of the shots

Nice vid on setting the exercises. Thanks. Would you happen to know how to program some dry contacts inside the controller panel to those green screw down connectors? I'm specifically looking to be able to have a set of dry contacts to tell me when there is no commercial power and one to tell me that the transfer switch is in the active mode to the generator. Thanks.

God fucking damnit i just replaced my timing belt and crank seal thinking that was what was leaking, inside of timing cover still full of oil after this has got to be it

What is the best solar panel set up for these??

Umm

I HATE STANDADYNE injection pumps I replace so many while in the Army, plus the HMWWVS had them garbage.

thank you for posting saved me 400 dollars you the man

My freespool knob shaft broke. Is there any ways to take that out?

Great video BUT a your hand is in the way to see which terminals you are touching with your metre when testing the switch

And uuuuuu and uuuuuuuuuu and uuuuuu you should really practice your script. It made it impossible to watch your video and uuuuu and uuuu

Brother I have one generator showing voltage fluctuation when I aplay load , please provide better solution Spectrum Detroit diesel(model:230 DSE)300 KVA generator

pronounced...generjunk....lol....did it have an hpanel in her or an older controller?

I love the video,,,minus the ats buzzz, lol. As an update, flightsystems has made a 1500 replacement that covers the 1000 1200 and 1500. They also do repairs on the original 1500. Also they repair the old 340 controllers as well. this is as june 2024. I do have a question though....do you remove the original transformer array as well?

I can't get over the heavy mouth breathing

I have the same kind, SG500MD, and if you pull the board out you will probably find the MOSFETS have the same thermal interface tape with the blue covering still on them. Likely preventing effective heat transfer to the case. It wasn't too hard to pull it apart and get the board half way out to pull the liner off the tape. Maybe a 20 minute job, hoping it fixes the throttling on hot days.

My favorite part of this is when you said "i was born a f-up, i know how to fix my problems"

“From here to here” ::covers “here” with his hand::

If it's starting and stopping, change your breaker. It's probably rusted all to hell in there, from the tape that's on it. (trapping moisture) inside it. Humidity will rust them out pretty quick.

I was just reading the manual for these and it says you can't replace the SCV and must replace the whole pump. Where did you get the SCV to replace? Did they change their stance or something?

Big thank you for sharing this - I literally just had the exact same problem, a nice easy solution!

Cool video thanks for posting you remind me of a mechanic in the last shopp i worked in

This is the only video in all internet of someone taking apart this specific vacuum. Mine stopped working and it’s got to be the switch or the motor.

How did you get the foot power switch off?

I used a paper clip. Worked just fine

The manual recommends installing seals last to prevent damage. Otherwise great video.

I need the software , can you help me..

One of my units do that if the low coolant temp comes on. Lights up like 6 different alarms.

allowable ampacity (AA) is permitted to be the 90deg when temperature correction factor necessitates application #2 THHN will have AA to be 130A * (say 0.96) Temp Correction Factor for hotter ambient = 124.8A to be connected to a 75deg terminal >> than by using THW at 115A , even though when no correction factor both THW & THHN have AA of conductor ampacity (CA) of 115A to a 75 deg terminal ; this is the advantage of using THHN in hot environments which the NEC permits .

Pro tip I just discovered if you submit a warranty claim in the first two months for defective item they send you a refund check and just tell you to dispose of the defective item. Free pump, boom.

My Kohler generator turns off after 2 minutes and sends the auxiliary failure alarm, what would be the reason?

I think your looking at the Exeter rotor and stator not the pmg, pmg would be behind that rotor.

Ehh umm ahh mmm ammm ehh. your boring ramblings I could only take for 6 minutes.

Please be gentle and be grateful. Not everyone can afford a new Ryobi or any brand of power tools.

There is no CURE or FIX for this type of cleaner!!! The first trouble, simply throw away and not waste time trying to fix it !!! You pay for what you get... It's a JUNK vac cleaner ........ Next time Buy a DYSON !!

Why did the last seal only last 20k?

Do you know if these generator ends are able to be wired for 230 volt?

This looks like the EGR off a C6.6 or C7.2, are you sure its from a C4.4?

go grab another beer and call it a day my buddy.

They say you should run for 30 hours for break in time without a load ... And they are know to run for 20.000 thousand hours before tear down ....

Are these the steps I need for delaying the start times? When I do a load test, I need the AC units to completely stop spinning before the Transfer switch swaps to generator power. The office equipment is on battery, so I have time. I want it to delay 4 minutes before the load is transfered.

This generator won't even run my small microwave.for 10 seconds. Maybe the power convertor was on charging the battery at the same time?

Great video! We have been dealing with a problem in a CTG 1200A ATS with the MX150 controller. The thing is, we set up the everything and genset run every test fine from the controller including load test, no load start, etc. The thing is that when we shut down the utility to test like in a real life situation: 1) I takes 1 exact minute to close the start relay, even when the start delay is set to the minimum time. 2) When it finally starts, as soon as the generator runs, the start relay opens and turns the genset off, and closes and open again and again until when stop it manually. 3) I’m not very familiar with the MX150, but the controller screen is supposed to turn off when the utility goes out? Any input on this will be appreciated!! Thanks 🙏🏻

Let’s say I wanted to lower the output rate to use for filling gopher tunnels with mud without risking blowing mud all over the lawn by accident. Could I cut the impeller blades down smaller and that would do it?

Hello my friend Can you tell me the app you use to connect wifi ?

How to connect tranferswitch to this controller?

I have similar problem but don't have parts available... please can you help.

*promosm*

Hook battery up first, duh

I think someone with better knowledge would do a better job explaining this job. Good riddens