Видео

How can I buy those windshield deflectors

I swear a toothpaste-eating meth head built my buggy frame. It is out of square and level all over. Ruined 2 pairs of rear shocks due to the diy mounts. I fixed all of the gremlins, just have to raise the rear Thanks for such a professional, concise and informative video!!!!!

Es usted grande Milo Manx, tiene razon nadie explico como usted el armado. Gracias

ABSOLUTELY BEAUTIFUL!!! I want it 😂👍

I think my dream is to own a Meyer Manx that you built. Love them. Wonderful work.

Thank you

Quit sucking a dang candy while doing videos , it's annoying

Milo my left turn signals are blowing a fuse. I’m thinking the front tire is rubbing on the wire and pulling it…Inspected the wires at the light and they seem ok (I’m buying a new housing just in case)…If the new housing doesn’t work where is it most likely to short? That bolt on the fuel tank, the fuel tank itself or the tunnel the wire goes through? Manx II (PO did the wiring I’m just trying to figure it out)

Are you still building these buggies I haven’t seen anymore of your videos. Hope you okay 👍

Awesome videos . The best tutorials I have found

I have a baja bug and someone raised it to where the spring plates ride on the stop all the time in fact I can’t push down on suspension to get it to move. I am assuming that the person that raised it just moved the outer splines to get the hight they wanted with no regard to how stiff the suspension would be. So how would I keep that ride height and soften the ride. Thanks

Very Helpful. This is going straight onto my resume! Thank you.

how is going, miss the video's , hope you are doing good

Where do the identification tags get riveted to the body???

Good to know.

wish I had seen this before I cut mine up 😭

What gas filler is that?

I am verry much enjoying learning from your videos . One thing to add to your 68 list ,and this I learned the hard way . A later 68 build has the bigger tie rods that came on the 69. Thanks

I have been enjoying watching and learning from your videos . I wonder if you could give me some advice ? So I recently purchaser a basket case Dean Jefferies Design sand buggy . It came with a 1600 souped up motor . The motor has a fiberglass fan shroud on it . There are two copper bungs coming out the back driver side . Would this be for an oil cooler or oil filter ? Their are no lines coming off the oil pump ,just a place to hook up a sender . Thanks for some help .

Hey milo, great video Do you know anything about the H code tranny ? Thanks

Hi Milo, I would like to ask if the transmission found on Beetle has hypoid mechanism to it? Because on the owners manual it states to use GL4 hypoid oil. I am deciding between the regular GL4 trans oil or other special hypoid oil. thank you!

thank you, I don't have a manx. But I find your information to be invaluable.

What color is this buggy

What color is this buggy

Would you be willing to make another dash frame ?

Are you still doing RUclips?

When you stated put the spring plate back on what you think is the same area??? Are you stating put the spring plate back on in the same position when you took it off?? Ore did you move it down one?

where did you get the motor for you buggy

I appreciate the fact unlike many youtubers you dont throw loud music in...i can set my volume and watch and learn without damaging my ears...I unsubscribed from many others because they dont seem to realize that if I wanted music I have my own...

Where did you get the parts for the steering column? I am looking to change mine out to something like the one you have.

What is the maximum ground clearance ca you adjust the swing axle?

For a swing axle, how high can we increase the height of the flooring? Can we lift it up to 15 inches?

Sold buy now right

For sale

I set both my left and right rear spring plates to 17 degrees and my drivers side front and rear is an inch lower than the passenger side. Am I missing something?

Wow so clean

Hi I noticed your wind deflectors And was wondering is there a place I could purchase some They seem quite nice

Hi Milo do you know where you can purchase the wind deflectors that you have on this buggy

More accuracy is gained by setting a scale below the end of the spring arm and preloading it by 2-3 lbs. More weight would require bolting the outer cup on to center the bushing(s).

Hey milo great content here. I recently upgraded from a generator to an alternator? I have a fuel pump question. I’ve opted for the mechanical alternator fuel pump. I have the correct lengthfuel pump rod but I had to notch the fuel pump stand to create the gap for the lever under the fuel pump. That all went great until I put the gaskets on. Do I also need to notch the gasket to create enough clearance for the lever that hangs below the pump? Sheesh I hope that all makes sense

With all the attention to detail, you could’ve put a nice 2 L

Milo why such a small motor in a single port

Looks great man! Will the "Mad Dog" pulley cover require the same thing?

Milo, how ya doing, haven’t seen any videos from you lately

Hello thank you for these videos I have a dune buggy sitting on a 1956 split window frame that's cut the 9.25in.or close. with a steel window frame. the fiberglass body style looks a lot like the one in this video ..the fiberglass is in 3 pieces dash, hood and main body. my question is ? how can i know if it is a Manx Dune Buggy. It is in rough shape and looks very old I am going to restore it as close to orig. as I can regardless this is cool and will be restored . Mr. Manx was a great builder and saddened by his passing..

I haven't seen anymore Milo videos since this one over a year ago does anyone know why as this is my favourite guy building buggies hope all's well with u Milo,.

My second is okay in my type 3, but first was slipping out on the overrun and then I missed a shift and first now unusable. In my case it has to be the dogs. I have a bunch of earlier swing axle transaxles to steal parts from, but zero spare IRS transaxles. I'm in for some pain. Still hopeful to find a used IRS box to swap in so I can rebuild mine or figure out a bus upgrade with LSD.

Where did you get the side deflectors

If your shift fork is worn, the synchro sleeve might not be grabbing the dog teeth all the way. Also the normal things like trans and motor mounts, or the shift detent system

Hey Milo, r u still building buggies?