Видео

Good job, looks like you worked hard doing this. You could have made this job easier with a few changes. Strip the sheathing before putting the cable in the box, the wires should be about 2 or 3 inches longer and roll them into the box, it would be easier to make your receptacle connections. You could have used 6/2 Romex and a NEMA 6-50 receptacle, I doubt that the 240v compressor or the 240v welder uses a neutral wire. The white wire would be marked with red or black tape at each end indicating hot. Using 6/3 Romex is not a bad idea though, as you may need it later. Just leave the white (neutral) wire capped with a wire nut in the box. The other end to be landed on the neutral bus bar in the sub panel as you did. While using a separate grounding lug was fine, you could have looped the wire directly around the green grounding screw and then to the receptacle. It's only a 10 gauge wire, not a 6 like the conductors. The neutral wire which is wired in presently should carry no current, because a 240v circuit is a balanced load by default. The neutral connection on a NEMA 14-50 is for loads, e.g. electrical dryers that also have 120v circuitry for the low power needs such as in the control panel lighting, etc.

5:50 6:05 6:16

I know for myself I try to use my space as much as possible and back my truck after bucking up a log than park my truck right close so it's easier let walking and more loading

Very nice video ,thanks

I used to work in a hydraulics/welding shop. The welder told me one time it doesn't really matter what the weld looks like, as long as you get good penetration it'll hold.

Nice video man. Turning scrap into something you can use. Looks great

I just did a similar video on how I built my tire holder on a trailer

There are tradeoffs with fences. It will help protect against pets or young kids from wandering into unsafe places, but if those are not a worry, then it looks more open and friendly without.

We loved our Trot-Bilt tillers. My dad still has his from the mid-'70s. Sweet machines.

I like the idea of the tire to get upward motion. I've not used that before. I've had good luck with soaking the roots for several hours with a hose. Even several hours per day over a few days, but our summers are super dry so that's maybe not needed in your area. I've also had good luck with an engine house. Thanks for sharing and keep up the good work.

This was fun.

I like it. Well done.

Bless you!

What is that switch you use to turn on the compressor on? Is it an appropriate amperage safety disconnect/switch?

Glad to see you are posting videos again.

Nice job! Ever set the beard on fire... LOL

Neat and Clean

Wires cut too short

Great work I will attempt the same.

6 agw wire? holy crap how many amps does your quincy draw

Could you make a short video on how your air compressor is wired in and how you made the power cord for it?

At 59 yrs. old, I am just now learning how to weld & fabricate. and your video is a great inspiration. Your design is ingenious in the way that it is a simple and basic one. I have been trying to figure out how to add a spare tire mount to my trailer for months but didn't know where to start or how to do it. but you have shown me the way. This will be a great place for me to start. thanks for taking the time to post this video. the best part is the use of basic tools so I don't need to buy more tools to do it.

What kind of grounding nut did you use? was it available at home depot? Please and thanks

Always remember even the prettiest welds are not the strongest. You did a great job .

Anda sangat hebat dan kuat ,bung pekerja keras

Nice work.

REAL SUGAR MT DEW!!! 👍

I think the fence being removed made it look more open and spacious for sure! Looking good!

Sweet as! I think my eyes would've been itching like crazy with that

I think that carpet had years of life left in it! You need to wear a mask when you’re pulling that crap up.

Tonya says it makes you look younger and skinnier..........maybe I should try shaving. LOL

You have given me a great idea. I am going to use time lapse for all future projects. It sure goes fast that way!

Looking good!!!! How are you going to remove the floor?

I know! I’m glad you still have them.

I know!! I hope to make it on one of these firewood hauls! Trailer is looking top notch! Don't go throwing crimpers when you re-wire it!

Mmmm….forbidden strawberries.

Watching you work is much better than working myself. Thanks taking care of that burden for me.

I’m famous I’ve been mentioned on youtube

Looks like fun.

It looks like fun. I wish I was there to help. I thought we were taught using sketchy, welded together, rusty chains that could kill you at any given time. You’ve taken the fear out of it using a new chain.

ya got to include Like, Tag, Share and Subscribe into your videos.

Looks great. I wish we could have been there for the stump pulling. My favorite part of stump pulling is listening to the roots pop as they are letting go.

Good to see ya making videos again. Good luck with the $$$ pit. It be fun tow watch

I love this video. Tania’s reaction is the best.

Great video. I look forward to more.

Alot better than the crap "carry on" sells. Spare tire holders like the one you made should be standard on all utility trailers

Great job, I love the design. Going to copy it for mine.

What chuck did you get?

I love your design! I am going to make one for my trailer. Good video.