Видео

As a hockey player and a plumber I approve this video

Did you had to re calibrate the gas valve you replaced?

I just got wind free for my bedrooms. They seem very large hanging on a bedroom wall. I've seen split duct in Europe and they don't seem as large. How in the world do I get the ugly label off of the side? very quiet and effective

I like that music! Great job.

Can I get a rebate now (2024)?

So is the glue for exhaust rated for the stack temp of exhaust.

Haha oh man I’ve seen some rough water heaters in my day but those 2 old tanks sure take the cake

Nice job.

How long did it take ? Any particular items to watch out for (other than gas line to blower housing) ?

Ridgid is Better

Nice job Mike!

Need To Explain what you are doing,.....if don't want people to know then don't Post it

Great video. I'm about to have to have a Ecoer 2436 installed. Question, what kind of thermostat will I need to run my existing propane furnace and my new heat pump? I guess what I was wondering what functionality will the thermostat need so I can search for one? Thank you

Overkill on copper

Not turning it fully on the last one smh

Remove the gas pipe assembley so you can remove the fan, makes the job much easier.

That's a great video thank you for posting that

There's a Boston accent! Nice job

What a great video of a classic Ecoer installation. You know it is done right when Ralph and Mike are on the job. System is complete with Ecoer exclusive gateway allowing for factory monitoring and assuring the home owner of a trouble and hassle free installation and the comfort of a 10 years parts and Labor warranty. Thank you DiBacco team.

I have been looking for a video that explains clearly and in detail how the zones and thermostats are connected on the navien ncb-240/110h(ng) and have not found anything. Please someone give the link to the correct video

I am sorry to say this, but why would you advertise such a poorly installed furnace. If you fabricated an onsite plenum transition with a roll of foil tape. I am a firm believer, if you have to use foil tape, you don't know how to work with sheet metal and just covering up sloppy work. Licensed Refrigeration Mechanic/Heating Technician Toronto, Canada and NATE Certified USA

Nice job. Cost?

Pipes are flexing on the wall with the filters. Are they adequately supported?

👍👍

It seems nobody wants to tell anybody how much they charge for this work, I can only guess why.

How much does this cost?

Is this pump stronger than the standard 1/3 HP, 4 AMP, type that attaches directly under the sink instead of off to the side like yours?

Beautiful work

That exhaust our door pipe needs to be angled down.

Why don’t u go with a hot water conducing boiler that hangs on the wall

How long did it take to do the replacement of the heat exchanger with any testing afterwards?

Loved your video! 🎥 After going through your description, I recommend adding some impactful tags and a standout thumbnail for more reach.

Could you have possibly gotten worse video angles.

i always wonder why you dont need flo checks for multi zone on the pumps

Why is it backing up and 3 inches of standing water? Need a bigger basket or pump?

Yep, just had a 180e installed in 30X40' single story home. Looks like the inside of a Russian submarine ! Gives out hot water ! I have a two zone system. Former was an oil system in a crawl space (4 ' high) and the furnace area was dug down another 2 feet. And that's where all the water from rain storms collected. Can't count the number of times the sump pump failed due to this or that kicking out the furnace. Had gas lines installed in our town. Made the switch due to the 55 year old oil tank in the crawl space too. This is in the upstairs, so no more rain problems. Our company installed plastic pipes, they seem to replace every pipe to the baseboard heaters. Heating pipes are 55 years old too. My condensation pump is over the ceiling into my laundry sink. Yours is just went out the wall.

Did you AAV? I can’t tell from the video.

✊🤘🤙👍

Why use copper for the hot and cold?

i dont see why you replaced the old one, just looks like it needed a lil freon....

I have always had a serious problem with people not plumbing in the relief. its just lazy. Do the job right no the easy way.

Hi., just watch your video., im here in canada ., just had leaks on my navien heat exchanger ., wanna know the parts cost, please and thank you

What did you charge for this job?

Just blew my first one today. Thanks for sharing

👍👍

👍👍

first video i have seen that actually shows how to turn it on which is what I been wondering how to do… for some reason my contractor has the lever facing up instead of down and what does that bottom one do after you turned it on? thanks for any help you give

You don’t buy the manifold ready to go on that ? 🤔

This was an exact replacement for the old one that lasted about 10 years. ruclips.net/user/postUgkx7yWIKcrbA9KMHkGSfcgxW2lsjHT6B8Sh The top of my mitigation tube by my roofline was just a 90 elbow which allowed too much debris to fall down into the fan, eventually ruining it. Without this issue, I bet it would have kept running another 10 years. When I replaced this fan, I added an extra elbow joint so the top tube now it does a 180, which should solve that problem. The radon guys around here wanted to charge me a $300 diagnostic fee, then parts/labor (probably close to $600 total). I installed this all by myself in about an hour for the cost of the fan; it would probably be even easier/faster with two people. FYI the manufacturer's warranty greatly differs depending on whether you install it yourself (1 yr warranty) or have a licensed installer do it (10 yrs).

I have a samsung outdoor unit, Error E202 U C8....It is about 6 years old so all conncections are fine and it always worked fine. Do you have any suggestions as I am having a lot of trouble getting information from samsung?