Видео

How much capacity in gear oil in a 30 HP obm

I've seen someone else remove that shift linkage cable without taking down the bracket. There's a u shaped metal clip that you gotta wiggle out of it's slot and then the linkage comes out. Not sure which is the easier method.

Will that even stick to straight chrome, longterm?

Oh man that’s easy

Looks good. I went with the Toyo 215s as well on Vox Montes and love the 15mm offset. What pressure are you running in yours? Factory pressure feels soft @ 33/32. But they max at 44 and that seems like too much.

What about the message?

Brilliant video, thanks

Thanks for the video, it was really informative. The subaru jackstand really came to the rescue in helping me remove the 17mm bolts and removing a stuck rotor, i just had to get creative with the angles and using the cars body.

I just got the same exact boat last week.mine is a 2011 lows with the same motor just curious when you run your motor with the muffs on in the driveway does the water coming out of the hole when it’s peeing out get hot? Mine pees out good but seems a little on the hot side. Thanks

Once its dry how long does it last?

where is the oil filter?

What the led fog light call

I replace my alternator, battery light and negative battery sensor/terminal and I have my battery light on. I suspect the tension for the serpentine belt is too loose. Do you have any recommendations on how to test this or how to tighten the tension?

so is there 2 belts? or just the one

Um you know those are your high beam lights. There is a volt reducer in the fender well that steps down the power making a day time light but goes full power when you hit the high beam switch… looks cool though👍🤔

What name brand is that where did you get it from

That’s horrible

HOw about alone on a real windy day and not like your building it in your living room?

there is an oil drain plug on the left side. if you drain it only by the plug on bottom that has the oil filter, a lot of of oil will remain in the engine

Awesome thank you.

This the old skool right here no drills and no rubber Malat lol.

So there’s only 5 spark plugs i got a 2016 legacy

What exhaust do you have in this video?

Nice work, no gasket goes between the lower unit when reinstalling? Just curious.

Thanks for the demonstration

Whats the parts number for the filter?

What did you use to clean the new rotors? I'm currently in the process of 1 more threaded screw out and then the new one goes on but I don't know what to use to clean the oil of the new rotor

Well done! Thanks! I appreciated your illumination with old shop light & incandescent bulb. Also good was not having to remove the leads to the colis! $400+ saved from dealer shop!

Is that a single cab or a crew cab

Looks like those sparkplugs were cross threaded last time they were replaced. I can see why...there is hardly any room to work here.

To those who said he forgot to “prime” the shocks…monotube shocks do NOT have to be primed before installation.

Thanks for making this video! Went on pretty easily! The hardest part was getting the clips off with just a flathead a CD driver, but I was determined to do it today. Works great, too! I would never have figured out the directions that came in that packed on my own. Even with help it doesn’t show or say much. So thanks again!

Would a swivel spark plug socket work? My car is due for the 60k mile service very soon

Great guide - just did mine. Getting a low-profile socket wrench is CRITICAL to this operation. Most socket wrenches are too thick to fit between the plug socket and the firewall on those back, hard to reach plugs. Also, definitely use a magnetic plug socket; not a rubber one. If the rubber comes off on the plug in that recess, you'll have a nightmare of a time getting the rubber grommet back off.

What if the belt acts like it doesn’t fit ?

how the hell did u get those bottom two bolts holding the battery case? my god mine are so tight its unreal

Can ypu use any key anytime? Or does it set the pins inside the lock for the first key?

I noticed you did not torque the spark plugs at the end when you put the spark plugs back in? Why is this. All my cars I have worked on I torque the spark plugs. Is this new?

whats the wrench size to take the passanger side box out i know you need an extension?

Where did you buy that wrap? Looks great.

Very good and clean video!! Thanks!

So you gotta take your hole dash apart?

Much needed for my project today. Great Video!

Do I need to replace the spark plug tube seals when I do this? Only have 60k on it

Whered you buy them from?

anyone have any idea how they do in the wind? We get some pretty good winds in western Utah

Excellent and very helpful video 👌🏾

your engine is similar to 2014 Forester, it was relatively easy compare to 2019 Forester with direct injection engine. much less room, I had to move some of the electrical wire connecting to engine computer unit. much less side room compare to 2014 model.

Pelican needs to do this at factory level

Did you wire to your trolling motor battery or starting battery?