Видео

That’s the biggest buildup of oil sludge in the engine bay, well I mean where the splash shield is located at. Doesn’t look like the previous owner cleaned the engine bay often.

A longer breaker bar with a ratcheting mechanism, makes this much easier. That big nut of the tool should be on the front. A few taps with a rubber mallet on the bearing to insure it's in straight.

Great tutorial. Thank you

Is there an explanation in schematic form? Good video, thank you.

Great video

How many sensors are there in total on the V8? And what is the camshaft phaser? I’ve heard to replace it there as well?

I get 11,50volts from solid brown? And 0 from red/brown.. How can it be "can" plus then..? Can you help me please?

I finally find the video that has my exact situation and can help me get this install done and the audio isn’t synced 😢

You can use a puller to extract the bearing race from the oil pan. The cv joint to the intermediate shaft should not wear. Its probably a bad cv joint or the intermediate shaft bearing is bad. Good luck buy no need to seal the shaft to the cv chalice no way any debris goes in there but hey if you think so....

This is so so helpful. I have a different android radio that has all the similar stuff but the instructions are bad or is for a newer Benz with plug in play. I have a 2003 e320. Your video has clear information of what each wire does and how to connect them in order for the android radio to successfully work. Again thank you

That hex bolt has a trq spec

BAD VIDEO BROTHER

Hi, Very good video, it made my impossible possible. Thank you very much.

Where do you find that decoder box all the ones I'm looking at don't have the green wires???

Mines is now on laying sound but Bluetooth connects and disconnects

Hi, does the steering wheel controls and the original car microphone also work with the fiber optic converter? Thanks a lot.

Are the cam position sensors in the location for cls 550

Great video. I just bought a 2016 cls 63 s amg. 53000 miles on it. That’s the first thing I am going to do. I have heard where people are unplugging the oil pump solenoid Have you done this. If so where is it and do you recommend it???? Thanks

Thank you very much for your video, very usefull. I m having a problem with the 3 Power wires. If i Connect the 3 Of them, radio works but all the car panel starts blinking. If I disconnect the on off wiring, blinking stops, but radio stop Working aswell. Any ideas?

My car did not even drop

You were very helpful. Thank you.

Great video for everyone who wants to learn from the master! 👏👏👏

From where you order them?

Did you get a clunk noise with these power stop pads?

I have a 2012 CLS550 and I'm having the same issue but can't find the parts, where did you get your parts from?

Was the bearing worn? I have humming noise and changed front differential wheel bearing

Did you fix that low speed noise? My 212 having the same mild roaring and slightly vibration at on 49-50 km/h.

What if I can’t find the green wires on my connection that goes to the big box but I can find them on the canbus decoder?

Guys, I have followed the instructions and wired the speaker cable to the existing car can bus, the new car can bus and the fibre optic converter but still cannot get stereo sound, absolutely nothing. Can any help with advise?

Where can I buy that Fiber optic Decoder with CAN wires ?

Hey man, thanks for the video! Keep it up 😎👌👏

You saved me $300 and educated me at the same time! You da man bro! 💪🏾🤜🏾🤛🏾

Schlecht video

Thank you so much for the inlightmen my challenge is I try to connect my aftermarket android system but finding it difficult the green and black connector

Thank u for a detailed video. Suler helpful. I am doing my stereo on 2008 cls and for some reason headunit does not power on. They only wire that i havent connected is wire from canbus box to cars can system. Also my decoder does not have 2 green wires. Only red wire labeled ACC. Do you think cars CAN system has to be connected ir order for unit to power on? Thank you for your time if you get a chance to answer.

I just bought a 2015 CLS 63S It had 53,000 miles.. I'll be watching your channel for all my future troubles

Mine check engine light came on , I went to AutoZone and they pointed out that camshaft sensor is bad I took all of them 3 were leaking, thanks for the video

Great video, thank you 🙏

Great finding. It’ll be nice to show step by step on how you got to remove the parts. I know it’s not as easy as it appears. I’ll love to do this on my CLS 63 as well.

Great job man. What made you change the axel?

'Promosm'

Well done

any drone？

I have w211 04 e320 is itabout same process 4matic.. love channel

Get to it already Jesus Christmas

Hey it’s finely nice to see the man behind the scenes 👌👏👏

I did the same on my E63 wagon but then had to go back and add in an H-pipe, like was inside the resonator, because without a crossover of some kind the exhaust pulses can't equalize and it made the exhaust (and car) shake too much for my liking. It made it feel like it had a misfire at idle. The H didn't really change the sound that much but an added benefit is it did get rid of some of the "fluttery" sound at idle. Either way, the exhaust sounds much better w/o the resonator.

Great video, but what is the exact name of the Optical Fiber Decoder Most Box for the car? Yours has 1 green and 1 black-green wire but all I can find almost everywhere have a black and a yellow and two jacks. Where did you get yours exactly?

Excellent thanks bro. I have a vibrations no noise and changed wheels tires, inner and outer tie rods torque arm sway links ball joints and still there. Gonna check my bearing

So you didn’t use the Powerbuilt tool right? Instead you use the Amazon brand ones correct